Merge pull request #142 from dimitre/invalid

invalid

.gitmodules

@@ -10,3 +10,6 @@
 [submodule "libraries/lv_arduino"]
 	path = libraries/lv_arduino
 	url = https://github.com/btx000/lv_arduino.git
+[submodule "libraries/lv_maixduino"]
+	path = libraries/lv_maixduino
+	url = https://github.com/littlevgl/lv_maixduino.git

README.md

@@ -1,21 +1,76 @@
 Maixduino
 ========
 
-Arduino core for Maix Board (K210)
+# Arduino Core for K210 based devices
 
 
+
+## Supported devices
+
+### Sipeed Maix series
+  - [Amigo](https://dl.sipeed.com/MAIX/HDK/Sipeed-Amigo)
+  - [Cube](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maix-Cube)
+  - [Go](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maix-GO)
+  - [Maixduino](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maixduino)
+  - [Dock](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maix-Dock)
+  - [BiT](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maix-Bit)
+  - [Nano](https://dl.sipeed.com/MAIX/HDK/Sipeed-Maix-Nano)
+
+### M5Stack
+ * [M5StickV](https://m5stack.com/products/stickv)
+ * [M5UnitV](https://m5stack.com/collections/m5-unit/products/unitv-ai-camera)
+
+### Various custom boards
+ * [LAMLOEI AOIT DAAN](https://github.com/lamloei/AIoTDaaN/tree/master/hardware/20190505-R2/AIoTDaaN_R2/pdf)
+ * [IOXGD4](https://github.com/ioxgd/IOXGD-hardware/tree/master/IOXGD4/pdf)
+
 ## Docs
 
-Docs: [maixduino.sipeed.com](https://maixduino.sipeed.com/)
+Docs: [wiki.sipeed.com](https://wiki.sipeed.com/soft/maixduino/zh/index.html)
 
 ## Install
 
 Refer install doc: [Install](https://maixduino.sipeed.com/en/get_started/install.html)
 
+## Installing
 
-## Other SDK
+### From Board Manager
+
+ 1. [Download and install the Arduino IDE](https://www.arduino.cc/en/Main/Software) (at least version v1.9.8)
+ 2. Start the Arduino IDE
+ 3. Go into Preferences
+ 4. Add ```https://dl.sipeed.com/MAIX/Maixduino/package_Maixduino_k210_index.json``` as an "Additional Board Manager URL"
+ 5. Open the Boards Manager from the Tools -> Board menu and install "Maixduino(K210)"
+ 6. Select your K210 board from the Tools -> Board menu
+
+### From git
+
+ 1. Follow steps from Board Manager section above
+ 2. ```cd <SKETCHBOOK>```, where ```<SKETCHBOOK>``` is your Arduino Sketch folder:
+  * OS X: ```~/Documents/Arduino```
+  * Linux: ```~/Arduino```
+  * Windows: ```~/Documents/Arduino```
+ 3. Create a folder named ```hardware```, if it does not exist, and change directories to it
+ 4. Clone this repo: ```git clone https://github.com/Sipeed/Maixduino Maixduino/k210```
+ 5. Restart the Arduino IDE
+
+### Firmware flashing
+The firmware of the K210 devices is updated with a Python-based [kflash](https://github.com/sipeed/kflash.py) cross-platform tool.
+Follow ```kflash``` github page on installation instruction.
+
+
+###### Change board settings in Tools section on the top of Arduino IDE
+
+ 1. Board: The same as your dev board
+ 2. Burn Toolfirmware: leave default, for Maix Go Kit - ```open-ec```
+ 3. Burn Baudrate: Decrease it if download fails
+ 4. Port: Serial port, e.g. ```/dev/ttyUSB0```
+ 5. Programmer: ```k-flash```
+
+## Credits
+
+This core is based on and compatible with the [Sipeed Maixduino Core](https://github.com/sipeed/Maixduino)
 
-If you want to code by scripts, refer to our [MaixPy](https://maixpy.sipeed.com)
 
 
 

boards.txt

@@ -1,45 +1,278 @@
-menu.clksrc              = CPU Clock Frequency
-menu.burn_tool_firmware  = Burn Tool Firmware
-menu.burn_baudrate       = Burn Baud Rate
-menu.toolsloc            = Tool Install Location
+menu.clksrc=CPU Clock Frequency
+menu.burn_tool_firmware=Burn Tool Firmware
+menu.burn_baudrate=Burn Baud Rate
+menu.toolsloc=Tool Install Location
+
+##################################################
+############# Sipeed Maix Amigo ###############
+
+amigo.name=Sipeed Maix Amigo
+
+## Toolchain
+amigo.menu.toolsloc.default=Default
+amigo.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+amigo.menu.clksrc.400=400MHz CPU Clock Frequency
+amigo.menu.clksrc.500=500MHz CPU Clock Frequency
+amigo.menu.clksrc.600=600MHz CPU Clock Frequency
+amigo.menu.clksrc.400.build.f_cpu=400000000L
+amigo.menu.clksrc.500.build.f_cpu=500000000L
+amigo.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+amigo.menu.burn_baudrate.2000000=2 Mbps
+amigo.menu.burn_baudrate.4500000=4.5 Mbps (Must open-ec!)
+amigo.menu.burn_baudrate.1500000=1.5 Mbps
+amigo.menu.burn_baudrate.1000000=1 Mbps
+amigo.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+amigo.menu.burn_baudrate.4500000.build.burn_baudrate=4500000
+amigo.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+amigo.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+amigo.menu.burn_tool_firmware.amigo=open-ec
+amigo.menu.burn_tool_firmware.amigo.build.burn_tool_firmware=goE
+
+## Core settings
+amigo.build.variant=sipeed_maix_amigo
+amigo.build.core=arduino
+
+## This sets a define for use in the compiled code.
+amigo.build.board=MAIX_AMIGO
+
+## This selects the tool from "programmers.txt"
+amigo.program.tool=kflash
+amigo.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+amigo.upload.maximum_size=8388608
+amigo.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# Sipeed Maix Cube ###############
+
+cube.name=Sipeed Maix Cube
+
+## Toolchain
+cube.menu.toolsloc.default=Default
+cube.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+cube.menu.clksrc.400=400MHz CPU Clock Frequency
+cube.menu.clksrc.500=500MHz CPU Clock Frequency
+cube.menu.clksrc.600=600MHz CPU Clock Frequency
+cube.menu.clksrc.400.build.f_cpu=400000000L
+cube.menu.clksrc.500.build.f_cpu=500000000L
+cube.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+cube.menu.burn_baudrate.1500000=1.5 Mbps
+cube.menu.burn_baudrate.1000000=1 Mbps
+cube.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+cube.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+cube.menu.burn_tool_firmware.cube=open-ec
+cube.menu.burn_tool_firmware.cube.build.burn_tool_firmware=goE
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+cube.build.variant=sipeed_maix_cube
+
+## "The 'core' file directory for this board, in ./cores
+cube.build.core=arduino
+
+## This sets a define for use in the compiled code.
+cube.build.board=MAIX_CUBE
+cube.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+cube.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+cube.upload.maximum_size=8388608
+cube.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+####################################################
+############### Sipeed Maix Go Board ###############
+
+go.name=Sipeed Maix Go
+
+## Toolchain
+go.menu.toolsloc.default=Default
+go.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+go.menu.clksrc.400=400MHz CPU Clock Frequency
+go.menu.clksrc.500=500MHz CPU Clock Frequency
+go.menu.clksrc.600=600MHz CPU Clock Frequency
+go.menu.clksrc.400.build.f_cpu=400000000L
+go.menu.clksrc.500.build.f_cpu=500000000L
+go.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+go.menu.burn_baudrate.2000000=2 Mbps
+go.menu.burn_baudrate.4500000=4.5 Mbps (Must open-ec!)
+go.menu.burn_baudrate.1500000=1.5 Mbps
+go.menu.burn_baudrate.1000000=1 Mbps
+go.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+go.menu.burn_baudrate.4500000.build.burn_baudrate=4500000
+go.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+go.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+go.menu.burn_tool_firmware.goE=open-ec
+go.menu.burn_tool_firmware.goD=CMSIS-DAP
+go.menu.burn_tool_firmware.goE.build.burn_tool_firmware=goE
+go.menu.burn_tool_firmware.goD.build.burn_tool_firmware=goD
+
+## Core settings
+## Point to the file for ./variants/<variant>/pins_arduino.h
+go.build.variant=sipeed_maix_go
+
+## "The 'core' file directory for this board, in ./cores
+go.build.core=arduino
+
+## This sets a define for use in the compiled code.
+go.build.board=MAIX_GO
+
+## This selects the tool from "programmers.txt"
+go.program.tool=kflash
+go.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+go.upload.maximum_size=8388608
+go.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# Sipeed Maixduino Board ###############
+
+mduino.name=Sipeed Maixduino
+
+## Toolchain
+mduino.menu.toolsloc.default=Default
+mduino.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+mduino.menu.clksrc.400=400MHz CPU Clock Frequency
+mduino.menu.clksrc.500=500MHz CPU Clock Frequency
+mduino.menu.clksrc.600=600MHz CPU Clock Frequency
+mduino.menu.clksrc.400.build.f_cpu=400000000L
+mduino.menu.clksrc.500.build.f_cpu=500000000L
+mduino.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+mduino.menu.burn_baudrate.1500000=1.5 Mbps
+mduino.menu.burn_baudrate.1000000=1 Mbps
+mduino.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+mduino.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+mduino.menu.burn_tool_firmware.mduino=Default
+mduino.menu.burn_tool_firmware.mduino.build.burn_tool_firmware=maixduino
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+mduino.build.variant=sipeed_maixduino
+
+## "The 'core' file directory for this board, in ./cores
+mduino.build.core=arduino
+
+## This sets a define for use in the compiled code.
+mduino.build.board=MAIX_DUINO
+mduino.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+mduino.program.tool=kflash
+mduino.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+mduino.upload.maximum_size=8388608
+mduino.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# Sipeed M1W Dock Board ###############
+
+m1w.name=Sipeed Maix Dock M1W
+
+## Toolchain
+m1w.menu.toolsloc.default=Default
+m1w.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+m1w.menu.clksrc.400=400MHz CPU Clock Frequency
+m1w.menu.clksrc.500=500MHz CPU Clock Frequency
+m1w.menu.clksrc.600=600MHz CPU Clock Frequency
+m1w.menu.clksrc.400.build.f_cpu=400000000L
+m1w.menu.clksrc.500.build.f_cpu=500000000L
+m1w.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+m1w.menu.burn_baudrate.2000000=2 Mbps
+m1w.menu.burn_baudrate.1500000=1.5 Mbps
+m1w.menu.burn_baudrate.1000000=1 Mbps
+m1w.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+m1w.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+m1w.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+m1w.menu.burn_tool_firmware.dan=Default
+m1w.menu.burn_tool_firmware.dan.build.burn_tool_firmware=dan
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+m1w.build.variant=sipeed_maix_one_w_dock
+
+## "The 'core' file directory for this board, in ./cores
+m1w.build.core=arduino
+
+## This sets a define for use in the compiled code.
+m1w.build.board=MAIX_DOCK_M1W
+m1w.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+m1w.program.tool=kflash
+m1w.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+m1w.upload.maximum_size=8388608
+m1w.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
 
 ##################################################
 ############# Sipeed M1 Dock Board ###############
 
-m1.name = Sipeed "Maix One Dock"/"Maix Bit" Board
+m1.name=Sipeed Maix Dock M1
 
 ## Toolchain
 m1.menu.toolsloc.default=Default
 m1.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
 
 ## CPU Clock
-m1.menu.clksrc.400 = 400MHz CPU Clock Frequency
-m1.menu.clksrc.500 = 500MHz CPU Clock Frequency
-m1.menu.clksrc.600 = 600MHz CPU Clock Frequency
-m1.menu.clksrc.400.build.f_cpu = 400000000L
-m1.menu.clksrc.500.build.f_cpu = 500000000L
-m1.menu.clksrc.600.build.f_cpu = 600000000L
+m1.menu.clksrc.400=400MHz CPU Clock Frequency
+m1.menu.clksrc.500=500MHz CPU Clock Frequency
+m1.menu.clksrc.600=600MHz CPU Clock Frequency
+m1.menu.clksrc.400.build.f_cpu=400000000L
+m1.menu.clksrc.500.build.f_cpu=500000000L
+m1.menu.clksrc.600.build.f_cpu=600000000L
 
 ## Burn baud rate
-m1.menu.burn_baudrate.2000000 = 2 Mbps
-m1.menu.burn_baudrate.1500000 = 1.5 Mbps
-m1.menu.burn_baudrate.1000000 = 1 Mbps
-m1.menu.burn_baudrate.2000000.build.burn_baudrate = 2000000
-m1.menu.burn_baudrate.1500000.build.burn_baudrate = 1500000
-m1.menu.burn_baudrate.1000000.build.burn_baudrate = 1000000
+m1.menu.burn_baudrate.2000000=2 Mbps
+m1.menu.burn_baudrate.1500000=1.5 Mbps
+m1.menu.burn_baudrate.1000000=1 Mbps
+m1.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+m1.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+m1.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
 
 ## Burn tool firmware
-m1.menu.burn_tool_firmware.dan = Default
-m1.menu.burn_tool_firmware.dan.build.burn_tool_firmware = dan
+m1.menu.burn_tool_firmware.dan=Default
+m1.menu.burn_tool_firmware.dan.build.burn_tool_firmware=dan
 
 ## Point to the file for ./variants/<variant>/pins_arduino.h
-m1.build.variant=sipeed_maix_one
+m1.build.variant=sipeed_maix_one_dock
 
 ## "The 'core' file directory for this board, in ./cores
 m1.build.core=arduino
 
 ## This sets a define for use in the compiled code.
-m1.build.board = BOARD_SIPEED_MAIX_ONE_DOCK
+m1.build.board=MAIX_DOCK_M1
 m1.build.sdata.size=512
 
 ## This selects the tool from "programmers.txt"
@@ -48,56 +281,281 @@ m1.upload.tool=kflash
 
 ## Limit is the 16MB Flash. Assume half is used for something else.
 m1.upload.maximum_size=8388608
-m1.build.ldscript={runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld
+m1.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
 
+##################################################
+############# Sipeed Maix Bit Board ###############
 
-####################################################
-############### Sipeed Maix Go Board ###############
-
-go.name = Sipeed Maix Go Board
-
+bit.name=Sipeed Maix Bit
 
 ## Toolchain
-go.menu.toolsloc.default=Default
-go.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+bit.menu.toolsloc.default=Default
+bit.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
 
 ## CPU Clock
-go.menu.clksrc.400 = 400MHz CPU Clock Frequency
-go.menu.clksrc.500 = 500MHz CPU Clock Frequency
-go.menu.clksrc.600 = 600MHz CPU Clock Frequency
-go.menu.clksrc.400.build.f_cpu = 400000000L
-go.menu.clksrc.500.build.f_cpu = 500000000L
-go.menu.clksrc.600.build.f_cpu = 600000000L
+bit.menu.clksrc.400=400MHz CPU Clock Frequency
+bit.menu.clksrc.500=500MHz CPU Clock Frequency
+bit.menu.clksrc.600=600MHz CPU Clock Frequency
+bit.menu.clksrc.400.build.f_cpu=400000000L
+bit.menu.clksrc.500.build.f_cpu=500000000L
+bit.menu.clksrc.600.build.f_cpu=600000000L
 
 ## Burn baud rate
-go.menu.burn_baudrate.2000000 = 2 Mbps
-go.menu.burn_baudrate.4500000 = 4.5 Mbps (Must open-ec!)
-go.menu.burn_baudrate.1500000 = 1.5 Mbps
-go.menu.burn_baudrate.1000000 = 1 Mbps
-go.menu.burn_baudrate.2000000.build.burn_baudrate = 2000000
-go.menu.burn_baudrate.4500000.build.burn_baudrate = 4500000
-go.menu.burn_baudrate.1500000.build.burn_baudrate = 1500000
-go.menu.burn_baudrate.1000000.build.burn_baudrate = 1000000
+bit.menu.burn_baudrate.2000000=2 Mbps
+bit.menu.burn_baudrate.1500000=1.5 Mbps
+bit.menu.burn_baudrate.1000000=1 Mbps
+bit.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+bit.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+bit.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
 
 ## Burn tool firmware
-go.menu.burn_tool_firmware.goE = open-ec
-go.menu.burn_tool_firmware.goD = CMSIS-DAP
-go.menu.burn_tool_firmware.goE.build.burn_tool_firmware = goE
-go.menu.burn_tool_firmware.goD.build.burn_tool_firmware = goD
+bit.menu.burn_tool_firmware.dan=Default
+bit.menu.burn_tool_firmware.dan.build.burn_tool_firmware=dan
 
-## Core settings
-go.build.variant= sipeed_maix_go
-go.build.core   = arduino
+## Point to the file for ./variants/<variant>/pins_arduino.h
+bit.build.variant=sipeed_maix_bit
+
+## "The 'core' file directory for this board, in ./cores
+bit.build.core=arduino
 
 ## This sets a define for use in the compiled code.
-go.build.board  = BOARD_SIPEED_MAIX_GO
+bit.build.board=MAIX_BIT
+bit.build.sdata.size=512
 
 ## This selects the tool from "programmers.txt"
-go.program.tool = kflash
-go.upload.tool  = kflash
+bit.program.tool=kflash
+bit.upload.tool=kflash
 
 ## Limit is the 16MB Flash. Assume half is used for something else.
-go.upload.maximum_size=8388608
-go.build.ldscript={runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld
+bit.upload.maximum_size=8388608
+bit.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
 
 
+##################################################
+############# Sipeed Maix Bit with Mic Board ###############
+
+bitm.name=Sipeed Maix Bit-Mic
+
+## Toolchain
+bitm.menu.toolsloc.default=Default
+bitm.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+bitm.menu.clksrc.400=400MHz CPU Clock Frequency
+bitm.menu.clksrc.500=500MHz CPU Clock Frequency
+bitm.menu.clksrc.600=600MHz CPU Clock Frequency
+bitm.menu.clksrc.400.build.f_cpu=400000000L
+bitm.menu.clksrc.500.build.f_cpu=500000000L
+bitm.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+bitm.menu.burn_baudrate.1500000=1.5 Mbps
+bitm.menu.burn_baudrate.1000000=1 Mbps
+bitm.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+bitm.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+bitm.menu.burn_tool_firmware.bitm=Default
+bitm.menu.burn_tool_firmware.bitm.build.burn_tool_firmware=bit-mic
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+bitm.build.variant=sipeed_maix_bit_mic
+
+## "The 'core' file directory for this board, in ./cores
+bitm.build.core=arduino
+
+## This sets a define for use in the compiled code.
+bitm.build.board=MAIX_BIT_M
+bitm.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+bitm.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+bitm.upload.maximum_size=8388608
+bitm.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# M5Stack M5StickV Stick ###############
+
+stickv.name=M5Stack M5StickV Stick
+
+## Toolchain
+stickv.menu.toolsloc.default=Default
+stickv.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+stickv.menu.clksrc.400=400MHz CPU Clock Frequency
+stickv.menu.clksrc.500=500MHz CPU Clock Frequency
+stickv.menu.clksrc.600=600MHz CPU Clock Frequency
+stickv.menu.clksrc.400.build.f_cpu=400000000L
+stickv.menu.clksrc.500.build.f_cpu=500000000L
+stickv.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+stickv.menu.burn_baudrate.1500000=1.5 Mbps
+stickv.menu.burn_baudrate.1000000=1 Mbps
+stickv.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+stickv.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+stickv.menu.burn_tool_firmware.stick1=CH340
+stickv.menu.burn_tool_firmware.stick1.build.burn_tool_firmware=bit-mic
+
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+stickv.build.variant=m5stack_m5stick_v
+
+## "The 'core' file directory for this board, in ./cores
+stickv.build.core=arduino
+
+## This sets a define for use in the compiled code.
+stickv.build.board=M5STICK_V
+stickv.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+stickv.program.tool=kflash
+stickv.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+stickv.upload.maximum_size=8388608
+stickv.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# M5Stack M5UnitV Camera ###############
+
+unitv.name=M5Stack M5UnitV Camera
+
+## Toolchain
+unitv.menu.toolsloc.default=Default
+unitv.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+unitv.menu.clksrc.400=400MHz CPU Clock Frequency
+unitv.menu.clksrc.500=500MHz CPU Clock Frequency
+unitv.menu.clksrc.600=600MHz CPU Clock Frequency
+unitv.menu.clksrc.400.build.f_cpu=400000000L
+unitv.menu.clksrc.500.build.f_cpu=500000000L
+unitv.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+unitv.menu.burn_baudrate.1500000=1.5 Mbps
+unitv.menu.burn_baudrate.1000000=1 Mbps
+unitv.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+unitv.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+unitv.menu.burn_tool_firmware.unit1=CH340
+unitv.menu.burn_tool_firmware.unit1.build.burn_tool_firmware=bit-mic
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+unitv.build.variant=m5stack_m5unit_v
+
+## "The 'core' file directory for this board, in ./cores
+unitv.build.core=arduino
+
+## This sets a define for use in the compiled code.
+unitv.build.board=M5UNIT_V
+unitv.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+unitv.program.tool=kflash
+unitv.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+unitv.upload.maximum_size=8388608
+unitv.build.ldscript="{runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld"
+
+##################################################
+############# LamLoei AIoT DaaN Board ###############
+
+aiotdaan.name=LamLoei AIoT DaaN
+
+## Toolchain
+aiotdaan.menu.toolsloc.default=Default
+aiotdaan.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+aiotdaan.menu.clksrc.400=400MHz CPU Clock Frequency
+aiotdaan.menu.clksrc.500=500MHz CPU Clock Frequency
+aiotdaan.menu.clksrc.600=600MHz CPU Clock Frequency
+aiotdaan.menu.clksrc.400.build.f_cpu=400000000L
+aiotdaan.menu.clksrc.500.build.f_cpu=500000000L
+aiotdaan.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+aiotdaan.menu.burn_baudrate.2000000=2 Mbps
+aiotdaan.menu.burn_baudrate.1500000=1.5 Mbps
+aiotdaan.menu.burn_baudrate.1000000=1 Mbps
+aiotdaan.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+aiotdaan.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+aiotdaan.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+aiotdaan.menu.burn_tool_firmware.dan=Default
+aiotdaan.menu.burn_tool_firmware.dan.build.burn_tool_firmware=dan
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+aiotdaan.build.variant=lamloei_aiot_daan
+
+## "The 'core' file directory for this board, in ./cores
+aiotdaan.build.core=arduino
+
+## This sets a define for use in the compiled code.
+aiotdaan.build.board=MAIX_DOCK_M1
+aiotdaan.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+aiotdaan.program.tool=kflash
+aiotdaan.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+aiotdaan.upload.maximum_size=8388608
+aiotdaan.build.ldscript={runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld
+
+##################################################
+############# IOXGD4 ###############
+
+ioxgd4.name=IOXGD4
+
+## Toolchain
+ioxgd4.menu.toolsloc.default=Default
+ioxgd4.menu.toolsloc.default.compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
+
+## CPU Clock
+ioxgd4.menu.clksrc.400=400MHz CPU Clock Frequency
+ioxgd4.menu.clksrc.500=500MHz CPU Clock Frequency
+ioxgd4.menu.clksrc.600=600MHz CPU Clock Frequency
+ioxgd4.menu.clksrc.400.build.f_cpu=400000000L
+ioxgd4.menu.clksrc.500.build.f_cpu=500000000L
+ioxgd4.menu.clksrc.600.build.f_cpu=600000000L
+
+## Burn baud rate
+ioxgd4.menu.burn_baudrate.2000000=2 Mbps
+ioxgd4.menu.burn_baudrate.1500000=1.5 Mbps
+ioxgd4.menu.burn_baudrate.1000000=1 Mbps
+ioxgd4.menu.burn_baudrate.2000000.build.burn_baudrate=2000000
+ioxgd4.menu.burn_baudrate.1500000.build.burn_baudrate=1500000
+ioxgd4.menu.burn_baudrate.1000000.build.burn_baudrate=1000000
+
+## Burn tool firmware
+ioxgd4.menu.burn_tool_firmware.dan=Default
+ioxgd4.menu.burn_tool_firmware.dan.build.burn_tool_firmware=dan
+
+## Point to the file for ./variants/<variant>/pins_arduino.h
+ioxgd4.build.variant=ioxgd4
+
+## "The 'core' file directory for this board, in ./cores
+ioxgd4.build.core=arduino
+
+## This sets a define for use in the compiled code.
+ioxgd4.build.board=MAIX_DOCK_M1
+ioxgd4.build.sdata.size=512
+
+## This selects the tool from "programmers.txt"
+ioxgd4.program.tool=kflash
+ioxgd4.upload.tool=kflash
+
+## Limit is the 16MB Flash. Assume half is used for something else.
+ioxgd4.upload.maximum_size=8388608
+ioxgd4.build.ldscript={runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lds/kendryte.ld

cores/arduino/HardwareSerial.h

@@ -29,6 +29,7 @@ class HardwareSerial : public Stream
     virtual void begin(uint32_t) {};
     virtual void end() {};
     virtual int available(void) = 0;
+    virtual int availableForWrite(void) = 0;
     virtual int peek(void) = 0;
     virtual int read(void) = 0;
     virtual void flush(void) = 0;

cores/arduino/Print.cpp

@@ -28,13 +28,42 @@
 #include "Print.h"
 
 // Public Methods //////////////////////////////////////////////////////////////
+size_t Print::printf(const char *format, ...)
+{
+    char loc_buf[64];
+    char * temp = loc_buf;
+    va_list arg;
+    va_list copy;
+    va_start(arg, format);
+    va_copy(copy, arg);
+    size_t len = vsnprintf(NULL, 0, format, arg);
+    va_end(copy);
+    if(len >= sizeof(loc_buf)){
+        temp = new char[len+1];
+        if(temp == NULL) {
+            return 0;
+        }
+    }
+    len = vsnprintf(temp, len+1, format, arg);
+    size_t ret = write((uint8_t*)temp, len);
+    va_end(arg);
+    if(len >= sizeof(loc_buf)){
+        delete[] temp;
+    }
+    return ret;
+}
 
 /* default implementation: may be overridden */
 size_t Print::write(const uint8_t *buffer, size_t size)
 {
   size_t n = 0;
   while (size--) {
-    n += write(*buffer++);
+    size_t ret = write(*buffer++);
+    if (ret == 0) {
+        // Write of last byte didn't complete, abort additional processing
+        break;
+    }
+    n += ret;
   }
   return n;
 }

cores/arduino/Print.h

@@ -25,6 +25,9 @@ extern "C"{
 #endif // __cplusplus
 #include <inttypes.h>
 #include <stdio.h> // for size_t
+#include <stdint.h>
+#include <stddef.h>
+#include <stdarg.h>
 #ifdef __cplusplus
 } // extern "C"
 #endif // __cplusplus
@@ -61,6 +64,7 @@ class Print
       return write((const uint8_t *)buffer, size);
     }
     
+    size_t printf(const char * format, ...)  __attribute__ ((format (printf, 2, 3)));
     size_t print(const __FlashStringHelper *);
     size_t print(const String &);
     size_t print(const char[]);

cores/arduino/Tone.cpp

@@ -6,7 +6,7 @@ extern pwm_fpio_set_t pwm_pins[VARIANT_NUM_PWM];
 
 void tone(uint8_t pin, unsigned int frequency, unsigned long duration)
 {
-    int8_t _pin = k210FpioSet(pin);
+    int8_t _pin = k210FpioSet(MD_PIN_MAP(pin));
     if(_pin >= 0){
         if (duration > 0) {
             pwm_set_frequency(pwm_pins[_pin].device, pwm_pins[_pin].channel,(double)frequency,0.5);
@@ -24,7 +24,7 @@ void tone(uint8_t pin, unsigned int frequency, unsigned long duration)
 
 void noTone(uint8_t pin) 
 {
-    int8_t _pin = k210FpioSet(pin);
+    int8_t _pin = k210FpioSet(MD_PIN_MAP(pin));
     if(_pin >= 0){
         pwm_set_enable(pwm_pins[_pin].device, pwm_pins[_pin].channel,0);
     }

cores/arduino/UARTClass.cpp

@@ -21,7 +21,7 @@
 #include <string.h>
 #include "UARTClass.h"
 
-#include "pins_arduino.h"
+#include "Arduino.h"
 #include "uarths.h"
 #include "fpioa.h"
 #include "sysctl.h"
@@ -63,11 +63,17 @@ UARTClass::UARTClass(uart_device_number_t device_select)
   }
 }
 
+void 
+UARTClass::begin(uint32_t dwBaudRate)
+{
+  begin(dwBaudRate, RX1, TX1);
+}
+
 void
 UARTClass::begin(uint32_t dwBaudRate, uint8_t _rx, uint8_t _tx)
 {
-  fpioa_set_function((int)_rx, this->_rxfunc);
-  fpioa_set_function((int)_tx, this->_txfunc);
+  fpioa_set_function(_rx, this->_rxfunc);
+  fpioa_set_function(_tx, this->_txfunc);
   uart_init(this->_uart);
   uart_configure(this->_uart, dwBaudRate, UART_BITWIDTH_8BIT, UART_STOP_1, UART_PARITY_NONE);
   this->_buff = new RingBuffer();
@@ -122,7 +128,7 @@ UARTClass::write(const uint8_t c)
   while (uart[this->_uart]->LSR & (1u << 5))
         continue;
   uart[this->_uart]->THR = c;
-  return 0;
+  return 1;
 }
 
 static int 
@@ -141,11 +147,17 @@ UARTHSClass::UARTHSClass()
 
 }
 
+void 
+UARTHSClass::begin(uint32_t dwBaudRate)
+{
+  begin(dwBaudRate, RX0, TX0);
+}
+
 void 
 UARTHSClass::begin(uint32_t dwBaudRate, uint8_t _rx, uint8_t _tx)
 {
-  fpioa_set_function((int)_rx, FUNC_UARTHS_RX);
-  fpioa_set_function((int)_tx, FUNC_UARTHS_TX);
+  fpioa_set_function((int)MD_PIN_MAP(_rx), FUNC_UARTHS_RX);
+  fpioa_set_function((int)MD_PIN_MAP(_tx), FUNC_UARTHS_TX);
   uarths_init();
   uarths_config(dwBaudRate, UARTHS_STOP_1);
   this->_buff = new RingBuffer();
@@ -165,8 +177,11 @@ UARTHSClass::end()
 size_t
 UARTHSClass::write(const uint8_t uc_data)
 {
-  uarths_putchar(uc_data);
-  return (1);
+  if (uarths_putchar(uc_data) == uc_data) {
+    return 1;
+  }
+
+  return 0;
 }
 
 static int
@@ -174,9 +189,9 @@ uarths_rec_callback(void *ctx)
 {
   int data;
   auto &driver = *reinterpret_cast<UARTHSClass *>(ctx);
-  data = uarths_getc();
-  if(data != 0){
+  data = uarths_getchar();
+  if(data != EOF){
     driver._buff->store_char((char)data);
   }
   return 0;
-}
+}

cores/arduino/UARTClass.h

@@ -27,12 +27,15 @@
 #include "pins_arduino.h"
 #include "RingBuffer.h"
 
+
+
 class UARTClass : public HardwareSerial
 {
   public:
     UARTClass();
     UARTClass(uart_device_number_t device_select);
-    void begin(uint32_t dwBaudRate, uint8_t _rx = 6, uint8_t _tx = 7);
+    void begin(uint32_t dwBaudRate);
+    void begin(uint32_t dwBaudRate, uint8_t _rx, uint8_t _tx);
     void end(void);
     int available(void);
     int availableForWrite(void);
@@ -57,7 +60,8 @@ class UARTHSClass : public UARTClass
 {
   public:
     UARTHSClass();
-    void begin(uint32_t dwBaudRate, uint8_t _rx = 4, uint8_t _tx = 5);
+    void begin(uint32_t dwBaudRate);
+    void begin(uint32_t dwBaudRate, uint8_t _rx, uint8_t _tx);
     void end(void);
     size_t write(const uint8_t c);
     using Print::write;

cores/arduino/WInterrupts.c

@@ -5,7 +5,7 @@
 
 void attachInterrupt(uint8_t intnum, voidFuncPtr user_callback, uint8_t mode)
 {
-    int gpionum = getGpio(intnum);
+    int gpionum = get_gpio(MD_PIN_MAP(intnum));
     if(gpionum >= 0){
         fpioa_function_t function = FUNC_GPIOHS0 + gpionum;
         fpioa_set_function(intnum, function);
@@ -34,7 +34,7 @@ void attachInterrupt(uint8_t intnum, voidFuncPtr user_callback, uint8_t mode)
 
 void detachInterrupt(uint8_t intnum)
 {
-    int gpionum = getGpio(intnum);
+    int gpionum = get_gpio(MD_PIN_MAP(intnum));
     if(gpionum >= 0){
         gpiohs_irq_unregister((uint8_t)gpionum);
     }

cores/arduino/wiring_analog.c

@@ -52,7 +52,7 @@ void analogOutputInit(void)
 
 void analogWrite(uint8_t ucPin, uint32_t ulValue )
 {
-    int8_t _pin = k210FpioSet(ucPin);
+    int8_t _pin = k210FpioSet(MD_PIN_MAP(ucPin));
     double _duty;
     if(_pin >= 0){
         _duty = dValueToDuty(ulValue);

cores/arduino/wiring_constants.h

@@ -65,11 +65,11 @@ enum BitOrder {
 #endif // abs
 
 #ifndef min
-#define min(a,b) ((a)<(b)?(a):(b))
+#define min(a,b) (((a)<(b))?(a):(b))
 #endif // min
 
 #ifndef max
-#define max(a,b) ((a)>(b)?(a):(b))
+#define max(a,b) (((a)>(b))?(a):(b))
 #endif // max
 
 #define abs(x) ((x)>0?(x):-(x))

cores/arduino/wiring_digital.c

@@ -13,55 +13,45 @@
 extern "C"{
 #endif // __cplusplus
 
+static int8_t _fpio_to_gpio_table[48]={-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1,-1};
+
 void pinMode(uint8_t dwPin, uint8_t dwMode){ 
-    int gpionum = getGpio(dwPin);
+    int gpionum = get_gpio(MD_PIN_MAP(dwPin));
     if(gpionum >= 0){
         fpioa_function_t function = FUNC_GPIOHS0 + gpionum;
-        fpioa_set_function(dwPin, function);
+        fpioa_set_function(MD_PIN_MAP(dwPin), function);
         gpiohs_set_drive_mode((uint8_t)gpionum, (gpio_drive_mode_t)dwMode);
     }
     return ;
 }
 
 void digitalWrite(uint8_t dwPin, uint8_t dwVal){
-    int gpionum = getGpio_s(dwPin);
-    if(gpionum >= 0){
-        gpiohs_set_pin((uint8_t)gpionum, (gpio_pin_value_t)dwVal);
+    int8_t gpio_pin = _fpio_to_gpio_table[MD_PIN_MAP(dwPin)];
+    if( gpio_pin >= 0){
+        gpiohs_set_pin((uint8_t)gpio_pin, (gpio_pin_value_t)dwVal);
     }
     return ;
 }
 
 int digitalRead(uint8_t dwPin){
-    int gpionum = getGpio_s(dwPin);
-    if(gpionum >= 0){
-        return (int)gpiohs_get_pin((uint8_t)gpionum);
+    int8_t gpio_pin = _fpio_to_gpio_table[MD_PIN_MAP(dwPin)];
+    if(gpio_pin >= 0){
+        return (int)gpiohs_get_pin((uint8_t)gpio_pin);
     }
     return -1;
 }
 
-int getGpio(uint8_t fpioPin) //分配一个gpio给fpio 输入 fpio 返回 gpiohs号
+int get_gpio(uint8_t fpio_pin)
 {
-    fpioa_function_t function = fpioa_get_function_buy_io(fpioPin);
-    if(function <= FUNC_GPIOHS31 && function >= FUNC_GPIOHS0 )
-    {
-        return (int)(function - FUNC_GPIOHS0);
+    if(_fpio_to_gpio_table[fpio_pin] >= 0){
+        return (int)_fpio_to_gpio_table[fpio_pin];
     }else{
-        return find_unused_gpiohs_io();        
+        _fpio_to_gpio_table[fpio_pin] = (int8_t)find_unused_gpiohs_io();
+        return (int)_fpio_to_gpio_table[fpio_pin];        
     }
 }
 
-int getGpio_s(uint8_t fpioPin) 
-{
-    fpioa_function_t function = fpioa_get_function_buy_io(fpioPin);
-    if(function <= FUNC_GPIOHS31 && function >= FUNC_GPIOHS0 )
-    {
-        return (int)(function - FUNC_GPIOHS0);
-    }else{
-        return -1;        
-    }
-}
-
-fpioa_function_t fpioa_get_function_buy_io(uint8_t fpioPin)
+fpioa_function_t fpioa_get_function_by_io(uint8_t fpioPin)
 {
     return (fpioa_function_t)fpioa->io[fpioPin].ch_sel ;
 }
@@ -79,6 +69,11 @@ int find_unused_gpiohs_io(void) //返回一个未使用的gpio ，失败返回-1
     return -1;
 }
 
+int read_fpio_to_gpio_table(int number)
+{
+    return _fpio_to_gpio_table[number];
+}
+
 #ifdef __cplusplus
 } // extern "C"
 #endif // __cplusplus

cores/arduino/wiring_digital.h

@@ -53,10 +53,10 @@ extern void digitalWrite( uint8_t dwPin, uint8_t dwVal ) ;
  */
 extern int digitalRead( uint8_t dwPin ) ;
 
-int getGpio(uint8_t fpioPin) ;
-int getGpio_s(uint8_t fpioPin) ;
-fpioa_function_t fpioa_get_function_buy_io(uint8_t fpioPin) ;
+int get_gpio(uint8_t fpio_pin) ;
+fpioa_function_t fpioa_get_function_by_io(uint8_t fpioPin) ;
 int find_unused_gpiohs_io(void) ;
+int read_fpio_to_gpio_table(int number);
 
 #ifdef __cplusplus
 } // extern "C"

libraries/AXP173/AXP173.cpp

@@ -0,0 +1,115 @@
+#include "AXP173.h"
+
+AXP173::AXP173()
+{
+  
+}
+
+void AXP173::begin(bool isInited)
+{
+    if(!isInited){
+        Wire.begin((uint8_t) SDA, (uint8_t) SCL, 400000);
+    }
+#if defined (ARDUINO_MAIX_AMIGO)
+    Write1Byte(0x27, 0x20); //LDO4 - 0.8V (default 0x48 1.8V)
+    Write1Byte(0x28, 0x0C); //LDO2/3 - LDO2 1.8V / LDO3 3.0V
+#else   //ARDUINO_MAIX_CUBE
+    Write1Byte(0x46, 0xFF); //Clear interupts
+    Write1Byte(0x33, 0xC1); //Set Bat Charging Voltage to 4V2, Current to 190mA
+    Write1Byte(0x10, (Read8bit(0x10) & 0xFC)); //EXTEN & DC-DC2 control
+#endif    
+}
+
+void AXP173::Write1Byte( uint8_t Addr ,  uint8_t Data )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.write(Data);
+    Wire.endTransmission();
+}
+
+uint8_t AXP173::Read8bit( uint8_t Addr )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 1);
+    return Wire.read();
+}
+
+uint16_t AXP173::Read12Bit( uint8_t Addr)
+{
+    uint16_t Data = 0;
+    uint8_t buf[2];
+    ReadBuff(Addr,2,buf);
+    Data = ((buf[0] << 4) + buf[1]);
+    return Data;
+}
+
+uint16_t AXP173::Read13Bit( uint8_t Addr)
+{
+    uint16_t Data = 0;
+    uint8_t buf[2];
+    ReadBuff(Addr,2,buf);
+    Data = ((buf[0] << 5) + buf[1]);
+    return Data;
+}
+
+uint16_t AXP173::Read16bit( uint8_t Addr )
+{
+    uint16_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 2);
+    for( int i = 0 ; i < 2 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+uint32_t AXP173::Read24bit( uint8_t Addr )
+{
+    uint32_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 3);
+    for( int i = 0 ; i < 3 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+uint32_t AXP173::Read32bit( uint8_t Addr )
+{
+    uint32_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 4);
+    for( int i = 0 ; i < 4 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+void AXP173::ReadBuff( uint8_t Addr , uint8_t Size , uint8_t *Buff )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, (int)Size);
+    for (int i = 0; i < Size; i++)
+    {
+        *( Buff + i )  = Wire.read();
+    }
+}
+
+

libraries/AXP173/AXP173.h

@@ -0,0 +1,53 @@
+#ifndef __AXP173_H__
+#define __AXP173_H__
+
+#include <Wire.h>
+#include <Arduino.h>
+
+#define SLEEP_MSEC(us) (((uint64_t)us) * 1000L)
+#define SLEEP_SEC(us)  (((uint64_t)us) * 1000000L)
+#define SLEEP_MIN(us)  (((uint64_t)us) * 60L * 1000000L)
+#define SLEEP_HR(us)   (((uint64_t)us) * 60L * 60L * 1000000L)
+
+#define AXP_ADDR 0X34
+
+#define CURRENT_100MA  (0b0000)
+#define CURRENT_190MA  (0b0001)
+#define CURRENT_280MA  (0b0010)
+#define CURRENT_360MA  (0b0011)
+#define CURRENT_450MA  (0b0100)
+#define CURRENT_550MA  (0b0101)
+#define CURRENT_630MA  (0b0110)
+#define CURRENT_700MA  (0b0111)
+
+class AXP173 {
+public:
+
+    AXP173();
+    /**
+     * DCDC1: 3V3 Main rail. When not set the stick shuts down
+     * DCDC2: 0V9 K210 VCore
+     * DCDC3: 1V8 Use unknown
+     * LDO1: Don't set GPIO1 as LDO
+     * LDO2: 2V8 Display backlight
+     * LDO3: 1V5 Display Control
+     * GPIO0: LDO1 LCD_BL
+     * EXTEN:
+     */
+    void  begin(bool isInited = false);
+
+
+public:
+    
+private:
+    void Write1Byte( uint8_t Addr ,  uint8_t Data );
+    uint8_t Read8bit( uint8_t Addr );
+    uint16_t Read12Bit( uint8_t Addr);
+    uint16_t Read13Bit( uint8_t Addr);
+    uint16_t Read16bit( uint8_t Addr );
+    uint32_t Read24bit( uint8_t Addr );
+    uint32_t Read32bit( uint8_t Addr );
+    void ReadBuff( uint8_t Addr , uint8_t Size , uint8_t *Buff );
+}; 
+
+#endif

libraries/AXP192/AXP192.cpp

@@ -0,0 +1,428 @@
+#include "AXP192.h"
+
+AXP192::AXP192()
+{
+  
+}
+
+void AXP192::begin(bool isInited)
+{
+    if(!isInited){
+        Wire.begin((uint8_t) SDA, (uint8_t) SCL, 400000);
+    }
+
+    Write1Byte(0x46, 0xFF); //Clear interupts
+    Write1Byte(0x23, 0x08); //Set DC-DC2 (VCore) to 0V9
+    Write1Byte(0x33, 0xC0); //Set Bat Charging Voltage to 4V2, Current to 100mA
+    Write1Byte(0x36, 0x0C); //Set 128ms power on, 4s power off
+    Write1Byte(0x91, 0xF0); //Set GPIO0 (TFT_BL) (from 0x70 (min)) to 3V3 (max)
+    Write1Byte(0x90, 0x02); //Set GPIO0 to LDO mode
+    Write1Byte(0x28, 0xF0); //VDD2.8V net: LDO2 3.3V,  VDD 1.5V net: LDO3 1.8V
+    Write1Byte(0x27, 0x2C); //VDD1.8V net: DC-DC3 1.8V
+    Write1Byte(0x12, 0xFF); //Enble all LDO/DC_DC and EXTEN
+    Write1Byte(0x23, 0x08); //VDD 0.9v net: DC-DC2 0.9V
+    Write1Byte(0x32, 0x46); //Enable bat detection
+    Write1Byte(0x39, 0xFC); //Disable Temp Protection (Sensor doesn't exist!)
+    Write1Byte(0x31, (Read8bit(0x31) & 0xf8) | (1 << 2)); // Set Power off voltage 3V0
+
+    fpioa_set_function(INTL_INT, (fpioa_function_t)(FUNC_GPIOHS0 + 26));
+    gpiohs_set_drive_mode(26, GPIO_DM_OUTPUT);
+    gpiohs_set_pin(26, GPIO_PV_HIGH); //Disable VBUS As Input, BAT->5V Boost->VBUS->Charing Cycle
+
+    msleep(20);
+}
+
+void AXP192::Write1Byte( uint8_t Addr ,  uint8_t Data )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.write(Data);
+    Wire.endTransmission();
+}
+
+uint8_t AXP192::Read8bit( uint8_t Addr )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 1);
+    return Wire.read();
+}
+
+uint16_t AXP192::Read12Bit( uint8_t Addr)
+{
+    uint16_t Data = 0;
+    uint8_t buf[2];
+    ReadBuff(Addr,2,buf);
+    Data = ((buf[0] << 4) + buf[1]);
+    return Data;
+}
+
+uint16_t AXP192::Read13Bit( uint8_t Addr)
+{
+    uint16_t Data = 0;
+    uint8_t buf[2];
+    ReadBuff(Addr,2,buf);
+    Data = ((buf[0] << 5) + buf[1]);
+    return Data;
+}
+
+uint16_t AXP192::Read16bit( uint8_t Addr )
+{
+    uint16_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 2);
+    for( int i = 0 ; i < 2 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+uint32_t AXP192::Read24bit( uint8_t Addr )
+{
+    uint32_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 3);
+    for( int i = 0 ; i < 3 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+uint32_t AXP192::Read32bit( uint8_t Addr )
+{
+    uint32_t ReData = 0;
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 4);
+    for( int i = 0 ; i < 4 ; i++ )
+    {
+        ReData <<= 8;
+        ReData |= Wire.read();
+    }
+    return ReData;
+}
+
+void AXP192::ReadBuff( uint8_t Addr , uint8_t Size , uint8_t *Buff )
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(Addr);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, (int)Size);
+    for (int i = 0; i < Size; i++)
+    {
+        *( Buff + i )  = Wire.read();
+    }
+}
+
+void AXP192::ScreenBreath(uint8_t brightness)
+{
+    if (brightness > 12) 
+    {
+        brightness = 12;
+    }
+    uint8_t buf = Read8bit( 0x28 );
+    Write1Byte( 0x28 , ((buf & 0x0f) | (brightness << 4)) );
+}
+
+// Return True = Battery Exist
+bool AXP192::GetBatState()
+{
+    if( Read8bit(0x01) | 0x20 )
+        return true;
+    else
+        return false;
+}
+
+// Input Power Status 
+uint8_t AXP192::GetInputPowerStatus()
+{
+    return Read8bit(0x00);
+}
+
+// Battery Charging Status 
+uint8_t AXP192::GetBatteryChargingStatus()
+{
+    return Read8bit(0x01);
+}
+
+//---------coulombcounter_from_here---------
+//enable: void EnableCoulombcounter(void); 
+//disable: void DisableCOulombcounter(void);
+//stop: void StopCoulombcounter(void);
+//clear: void ClearCoulombcounter(void);
+//get charge data: uint32_t GetCoulombchargeData(void);
+//get discharge data: uint32_t GetCoulombdischargeData(void);
+//get coulomb val affter calculation: float GetCoulombData(void);
+//------------------------------------------
+void  AXP192::EnableCoulombcounter(void)
+{
+    Write1Byte( 0xB8 , 0x80 );
+}
+
+void  AXP192::DisableCoulombcounter(void)
+{
+    Write1Byte( 0xB8 , 0x00 );
+}
+
+void  AXP192::StopCoulombcounter(void)
+{
+    Write1Byte( 0xB8 , 0xC0 );
+}
+
+void  AXP192::ClearCoulombcounter(void)
+{
+    Write1Byte( 0xB8, Read8bit(0xB8) | 0x20);    // Only set the Clear Flag
+}
+
+uint32_t AXP192::GetCoulombchargeData(void)
+{
+    return Read32bit(0xB0);
+}
+
+uint32_t AXP192::GetCoulombdischargeData(void)
+{
+    return Read32bit(0xB4);
+}
+
+float AXP192::GetCoulombData(void)
+{
+    uint32_t coin = GetCoulombchargeData();
+    uint32_t coout = GetCoulombdischargeData();
+    uint32_t valueDifferent = 0;
+    bool bIsNegative = false;
+
+    if (coin > coout)
+    {    // Expected, in always more then out
+        valueDifferent = coin - coout;
+    }
+    else
+    {    // Warning: Out is more than In, the battery is not started at 0% 
+        // just Flip the output sign later
+        bIsNegative = true;
+        valueDifferent = coout - coin;
+    }
+    //c = 65536 * current_LSB * (coin - coout) / 3600 / ADC rate
+    //Adc rate can be read from 84H, change this variable if you change the ADC reate
+    float ccc = (65536 * 0.5 * valueDifferent) / 3600.0 / 200.0;  // Note the ADC has defaulted to be 200 Hz
+
+    if( bIsNegative )
+        ccc = 0.0 - ccc;    // Flip it back to negative
+    return ccc;
+}
+//----------coulomb_end_at_here----------
+
+uint8_t AXP192::GetWarningLeve(void)
+{
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(0x47);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 1);
+    uint8_t buf = Wire.read();
+    return (buf & 0x01);
+}
+
+void AXP192::SetSleep(void)
+{
+    Write1Byte(0x31 , Read8bit(0x31) | ( 1 << 3)); // Turn on short press to wake up
+    Write1Byte(0x90 , Read8bit(0x90) | 0x07); // GPIO1 floating
+    Write1Byte(0x82, 0x00); // Disable ADCs
+    Write1Byte(0x12, Read8bit(0x12) & 0xA1); // Disable all outputs but DCDC1
+}
+
+// Return 0 = not press, 0x01 = long press(1.5s), 0x02 = short press
+uint8_t AXP192::GetBtnPress()
+{
+    uint8_t state = Read8bit(0x46);  // IRQ 3 status.  
+    if(state) 
+    {
+        Write1Byte( 0x46 , 0x03 );   // Write 1 back to clear IRQ
+    }
+    return state;
+}
+
+// Low Volt Level 1, when APS Volt Output < 3.4496 V
+// Low Volt Level 2, when APS Volt Output < 3.3992 V, then this flag is SET (0x01)
+// Flag will reset once battery volt is charged above Low Volt Level 1
+// Note: now AXP192 have the Shutdown Voltage of 3.0V (B100) Def in REG 31H
+uint8_t AXP192::GetWarningLevel(void)
+{
+    return Read8bit(0x47) & 0x01;
+}
+
+float AXP192::GetBatVoltage()
+{
+    float ADCLSB = 1.1 / 1000.0;
+    uint16_t ReData = Read12Bit( 0x78 );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetBatCurrent()
+{
+    float ADCLSB = 0.5;
+    uint16_t CurrentIn = Read13Bit( 0x7A );
+    uint16_t CurrentOut = Read13Bit( 0x7C );
+    return ( CurrentIn - CurrentOut ) * ADCLSB;
+}
+
+float AXP192::GetVinVoltage()
+{
+    float ADCLSB = 1.7 / 1000.0;
+    uint16_t ReData = Read12Bit( 0x56 );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetVinCurrent()
+{
+    float ADCLSB = 0.625;
+    uint16_t ReData = Read12Bit( 0x58 );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetVBusVoltage()
+{
+    float ADCLSB = 1.7 / 1000.0;
+    uint16_t ReData = Read12Bit( 0x5A );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetVBusCurrent()
+{
+    float ADCLSB = 0.375;
+    uint16_t ReData = Read12Bit( 0x5C );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetTempInAXP192()
+{
+    float ADCLSB = 0.1;
+    const float OFFSET_DEG_C = -144.7;
+    uint16_t ReData = Read12Bit( 0x5E );
+    return OFFSET_DEG_C + ReData * ADCLSB;
+}
+
+float AXP192::GetBatPower()
+{
+    float VoltageLSB = 1.1;
+    float CurrentLCS = 0.5;
+    uint32_t ReData = Read24bit( 0x70 );
+    return  VoltageLSB * CurrentLCS * ReData/ 1000.0;
+}
+
+float AXP192::GetBatChargeCurrent()
+{
+    float ADCLSB = 0.5;
+    uint16_t ReData = Read13Bit( 0x7A );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetAPSVoltage()
+{
+    float ADCLSB = 1.4  / 1000.0;
+    uint16_t ReData = Read12Bit( 0x7E );
+    return ReData * ADCLSB;
+}
+
+float AXP192::GetBatCoulombInput()
+{
+    uint32_t ReData = Read32bit( 0xB0 );
+    return ReData * 65536 * 0.5 / 3600 /25.0;
+}
+
+float AXP192::GetBatCoulombOut()
+{
+    uint32_t ReData = Read32bit( 0xB4 );
+    return ReData * 65536 * 0.5 / 3600 /25.0;
+}
+
+// Can turn LCD Backlight OFF for power saving
+void AXP192::SetLDO2( bool State )
+{
+    uint8_t buf = Read8bit(0x12);
+    if( State == true )
+    {
+        buf = (1<<2) | buf;
+    }
+    else
+    {
+        buf = ~(1<<2) & buf;
+    }
+    Write1Byte( 0x12 , buf );
+}
+
+void AXP192::SetLDO3(bool State)
+{
+    uint8_t buf = Read8bit(0x12);
+    if( State == true )
+    {
+        buf = (1<<3) | buf;
+    }
+    else
+    {
+        buf = ~(1<<3) & buf;
+    }
+    Write1Byte( 0x12 , buf );
+}
+
+// Not recommend to set charge current > 100mA, since Battery is only 80mAh.
+// more then 1C charge-rate may shorten battery life-span.
+void AXP192::SetChargeCurrent(uint8_t current)
+{
+    uint8_t buf = Read8bit(0x33);
+    buf = (buf & 0xf0) | (current & 0x07);
+    Write1Byte(0x33, buf);
+}
+
+// Cut all power, except for LDO1 (RTC)
+void AXP192::PowerOff()
+{
+    Write1Byte(0x32, Read8bit(0x32) | 0x80);     // MSB for Power Off
+}
+
+void AXP192::SetAdcState(bool state)
+{
+    Write1Byte(0x82, state ? 0xff : 0x00);  // Enable / Disable all ADCs
+}
+
+// AXP192 have a 6 byte storage, when the power is still valid, the data will not be lost
+void AXP192::Read6BytesStorage( uint8_t *bufPtr )
+{
+    // Address from 0x06 - 0x0B
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(0x06);
+    Wire.endTransmission();
+    Wire.requestFrom(AXP_ADDR, 6);
+    for( int i = 0; i < 6; ++i )
+    {
+        bufPtr[i] = Wire.read();
+    }
+}
+
+// AXP192 have a 6 byte storage, when the power is still valid, the data will not be lost
+void AXP192::Write6BytesStorage( uint8_t *bufPtr )
+{
+    // Address from 0x06 - 0x0B
+    Wire.beginTransmission(AXP_ADDR);
+    Wire.write(0x06);
+    Wire.write(bufPtr[0]);
+    Wire.write(0x07);
+    Wire.write(bufPtr[1]);
+    Wire.write(0x08);
+    Wire.write(bufPtr[2]);
+    Wire.write(0x09);
+    Wire.write(bufPtr[3]);
+    Wire.write(0x0A);
+    Wire.write(bufPtr[4]);
+    Wire.write(0x0B);
+    Wire.write(bufPtr[5]);
+    Wire.endTransmission();
+}

libraries/AXP192/AXP192.h

@@ -0,0 +1,94 @@
+#ifndef __AXP192_H__
+#define __AXP192_H__
+
+#include <Wire.h>
+#include <Arduino.h>
+
+#define SLEEP_MSEC(us) (((uint64_t)us) * 1000L)
+#define SLEEP_SEC(us)  (((uint64_t)us) * 1000000L)
+#define SLEEP_MIN(us)  (((uint64_t)us) * 60L * 1000000L)
+#define SLEEP_HR(us)   (((uint64_t)us) * 60L * 60L * 1000000L)
+
+#define AXP_ADDR 0X34
+
+#define CURRENT_100MA  (0b0000)
+#define CURRENT_190MA  (0b0001)
+#define CURRENT_280MA  (0b0010)
+#define CURRENT_360MA  (0b0011)
+#define CURRENT_450MA  (0b0100)
+#define CURRENT_550MA  (0b0101)
+#define CURRENT_630MA  (0b0110)
+#define CURRENT_700MA  (0b0111)
+
+class AXP192 {
+public:
+
+    AXP192();
+    /**
+     * DCDC1: 3V3 Main rail. When not set the stick shuts down
+     * DCDC2: 0V9 K210 VCore
+     * DCDC3: 1V8 Use unknown
+     * LDO1: Don't set GPIO1 as LDO
+     * LDO2: 2V8 Display backlight
+     * LDO3: 1V5 Display Control
+     * GPIO0: LDO1 LCD_BL
+     * EXTEN:
+     */
+    void  begin(bool isInited = false);
+    void  ScreenBreath(uint8_t brightness);
+    bool  GetBatState();
+  
+    uint8_t GetInputPowerStatus();
+    uint8_t GetBatteryChargingStatus();
+
+    void  EnableCoulombcounter(void);
+    void  DisableCoulombcounter(void);
+    void  StopCoulombcounter(void);
+    void  ClearCoulombcounter(void);
+    uint32_t GetCoulombchargeData(void);        // Raw Data for Charge
+    uint32_t GetCoulombdischargeData(void);     // Raw Data for Discharge
+    float GetCoulombData(void);                 // total in - total out and calc
+    uint8_t GetBtnPress(void);
+    void SetSleep(void);
+    uint8_t GetWarningLeve(void);
+
+public:
+    // void SetChargeVoltage( uint8_t );
+    void  SetChargeCurrent( uint8_t );
+    float GetBatVoltage();
+    float GetBatCurrent();
+    float GetVinVoltage();
+    float GetVinCurrent();
+    float GetVBusVoltage();
+    float GetVBusCurrent();
+    float GetTempInAXP192();
+    float GetBatPower();
+    float GetBatChargeCurrent();
+    float GetAPSVoltage();
+    float GetBatCoulombInput();
+    float GetBatCoulombOut();
+    uint8_t GetWarningLevel(void);    
+    void SetLDO2( bool State );     // Can turn LCD Backlight OFF for power saving
+    void SetLDO3( bool State );
+    void SetAdcState(bool State);
+    
+    // -- Power Off
+    void PowerOff();
+
+    // Power Maintained Storage
+    void Read6BytesStorage( uint8_t *bufPtr );
+    void Write6BytesStorage( uint8_t *bufPtr );
+
+    
+private:
+    void Write1Byte( uint8_t Addr ,  uint8_t Data );
+    uint8_t Read8bit( uint8_t Addr );
+    uint16_t Read12Bit( uint8_t Addr);
+    uint16_t Read13Bit( uint8_t Addr);
+    uint16_t Read16bit( uint8_t Addr );
+    uint32_t Read24bit( uint8_t Addr );
+    uint32_t Read32bit( uint8_t Addr );
+    void ReadBuff( uint8_t Addr , uint8_t Size , uint8_t *Buff );
+}; 
+
+#endif

libraries/Camera/keywords.txt

@@ -19,7 +19,7 @@ id                   KEYWORD2
 snapshot             KEYWORD2
 getRGB565            KEYWORD2
 getRGB888            KEYWORD2
-setRotaion           KEYWORD2
+setRotation          KEYWORD2
 setInver             KEYWORD2
 width                KEYWORD2
 height               KEYWORD2

libraries/Camera/src/Camera.h

@@ -5,7 +5,7 @@
 #include <stdbool.h>
 
 typedef enum {
-    PIXFORMAT_INVLAID = 0,
+    PIXFORMAT_INVALID = 0,
     PIXFORMAT_BAYER,     // RAW
     PIXFORMAT_RGB565,    // RGB565
     PIXFORMAT_YUV422,    // YUV422
@@ -76,8 +76,9 @@ public:
      *                                    e.g. two RED pixel: {0xFF, 0xFF, 0x00, 0x00, 0x00, 0x00}
      */
     virtual uint8_t* getRGB888(){ return nullptr; };
-    virtual void setRotaion(uint8_t rotation) = 0;
+    virtual void setRotation(uint8_t rotation) = 0;
     virtual void setInvert(bool invert) = 0;
+    virtual void flip(bool horiz, bool vert);
 
 
     virtual int width(){ return _width; }

libraries/MSA300/examples/msa_basic/msa_basic.ino

@@ -1,27 +1,39 @@
 #include <MSA300.h>
 #include <Wire.h>
 
+// This is the length of the string that will be created
+// included minus and decimal point
+const signed char formattedStringLength = 11;
+
+//  The number of digits after the deimal point to print
+const unsigned char numVarsAfterDecimal = 6;
+
 acc_t data;
 MSA300 msa;
 
-void setup() {
-  // put your setup code here, to run once:
+static char outstr[formattedStringLength];
+
+char * formatValue(float value)
+{
+  dtostrf(value, formattedStringLength, numVarsAfterDecimal, outstr);
+  return outstr;
+}
+
+void setup()
+{
   Serial.begin(9600);
   Wire.begin();
   msa.begin();
-
-  
-  
 }
 
-void loop() {
-  // put your main code here, to run repeatedly:
+void loop()
+{
   data = msa.getAcceleration();
-  Serial.print("Xa:");
-  Serial.print(data.x);
-  Serial.print("Ya:");
-  Serial.print(data.y);
-  Serial.print("Za:");
-  Serial.println(data.z);
+
+  Serial.printf("Xa:%s ", formatValue(data.x));
+  Serial.printf("Ya:%s ", formatValue(data.y));
+  Serial.printf("Za:%s", formatValue(data.z));
+  Serial.println();
+
   delay(100);
 }

libraries/Maix_Speech_Recognition/examples/get_voice_model/get_voice_model.ino

@@ -0,0 +1,20 @@
+#include "Maix_Speech_Recognition.h"
+
+SpeechRecognizer rec;
+
+void setup()
+{ 
+    rec.begin();
+    Serial.begin(115200);
+    Serial.println("start rec...");
+    if( rec.record(0, 0) == 0) //keyword_num, model_num 
+    {    
+      rec.print_model(0, 0);
+    }
+    else 
+        Serial.println("rec failed");
+}
+
+void loop()
+{
+}

libraries/Maix_Speech_Recognition/examples/voice_control_led_en/voice_control_led_en.ino

@@ -0,0 +1,71 @@
+#include "Maix_Speech_Recognition.h"
+#include "voice_model.h"
+
+SpeechRecognizer rec;
+
+void setup()
+{
+    pinMode(LED_RED, OUTPUT);
+    pinMode(LED_BLUE, OUTPUT);
+    pinMode(LED_GREEN, OUTPUT);
+    rec.begin();
+    Serial.begin(115200);
+    Serial.println("init model...");
+    rec.addVoiceModel(0, 0, red_0, fram_num_red_0); 
+    rec.addVoiceModel(0, 1, red_1, fram_num_red_1); 
+    rec.addVoiceModel(0, 2, red_2, fram_num_red_2); 
+    rec.addVoiceModel(0, 3, red_3, fram_num_red_3); 
+    rec.addVoiceModel(1, 0, green_0, fram_num_green_0);     
+    rec.addVoiceModel(1, 1, green_1, fram_num_green_1);     
+    rec.addVoiceModel(1, 2, green_2, fram_num_green_2);     
+    rec.addVoiceModel(1, 3, green_3, fram_num_green_3);     
+    rec.addVoiceModel(2, 0, blue_0, fram_num_blue_0);   
+    rec.addVoiceModel(2, 1, blue_1, fram_num_blue_1);   
+    rec.addVoiceModel(2, 2, blue_2, fram_num_blue_2);   
+    rec.addVoiceModel(2, 3, blue_3, fram_num_blue_3);   
+    rec.addVoiceModel(3, 0, turnoff_0, fram_num_turnoff_0);  
+    rec.addVoiceModel(3, 1, turnoff_1, fram_num_turnoff_1);  
+    rec.addVoiceModel(3, 2, turnoff_2, fram_num_turnoff_2);  
+    rec.addVoiceModel(3, 3, turnoff_3, fram_num_turnoff_3);  
+    Serial.println("init model ok!");
+}
+void loop()
+{
+    int res;
+    res = rec.recognize();
+    Serial.printf("res : %d ", res);
+    if (res > 0){
+        switch (res)
+        {
+        case 1:
+            digitalWrite(LED_RED, LOW); //power on red led
+            digitalWrite(LED_GREEN, HIGH);
+            digitalWrite(LED_BLUE, HIGH);
+            Serial.println("rec : red ");
+            break;
+        case 2:
+            digitalWrite(LED_GREEN, LOW); //power on green led
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_BLUE, HIGH);
+            Serial.println("rec : green ");
+            break;
+        case 3:
+            digitalWrite(LED_BLUE, LOW); //power on blue led
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_GREEN, HIGH);
+            Serial.println("rec : blue ");
+            break;
+        case 4:
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_GREEN, HIGH);
+            digitalWrite(LED_BLUE, HIGH);   //power off all leds
+            Serial.println("rec : turnoff ");
+        default:
+            break;
+        }
+    }else
+    {
+        Serial.println("recognize failed.");
+    }
+    delay(1000);
+}

libraries/Maix_Speech_Recognition/examples/voice_control_led_zh/voice_control_led_zh.ino

@@ -0,0 +1,71 @@
+#include "Maix_Speech_Recognition.h"
+#include "voice_model.h"
+
+SpeechRecognizer rec;
+
+void setup()
+{
+    pinMode(LED_RED, OUTPUT);
+    pinMode(LED_BLUE, OUTPUT);
+    pinMode(LED_GREEN, OUTPUT);
+    rec.begin();
+    Serial.begin(115200);
+    Serial.println("init model...");
+    rec.addVoiceModel(0, 0, hongse_0, fram_num_hongse_0); //36
+    rec.addVoiceModel(0, 1, hongse_1, fram_num_hongse_1); //20
+    rec.addVoiceModel(0, 2, hongse_2, fram_num_hongse_2); //23
+    rec.addVoiceModel(0, 3, hongse_3, fram_num_hongse_3); //21
+    rec.addVoiceModel(1, 0, lvse_0, fram_num_lvse_0);     //20
+    rec.addVoiceModel(1, 1, lvse_1, fram_num_lvse_1);     //37
+    rec.addVoiceModel(1, 2, lvse_2, fram_num_lvse_2);     //19
+    rec.addVoiceModel(1, 3, lvse_3, fram_num_lvse_3);     //26
+    rec.addVoiceModel(2, 0, lanse_0, fram_num_lanse_0);   //19
+    rec.addVoiceModel(2, 1, lanse_1, fram_num_lanse_1);   //21
+    rec.addVoiceModel(2, 2, lanse_2, fram_num_lanse_2);   //28
+    rec.addVoiceModel(2, 3, lanse_3, fram_num_lanse_3);   //22
+    rec.addVoiceModel(3, 0, guandeng_0, fram_num_guandeng_0);  //26
+    rec.addVoiceModel(3, 1, guandeng_1, fram_num_guandeng_1);  //29
+    rec.addVoiceModel(3, 2, guandeng_2, fram_num_guandeng_2);  //33
+    rec.addVoiceModel(3, 3, guandeng_3, fram_num_guandeng_3);  //29
+    Serial.println("init model ok!");
+}
+void loop()
+{
+    int res;
+    res = rec.recognize();
+    Serial.printf("res : %d ", res);
+    if (res > 0){
+        switch (res)
+        {
+        case 1:
+            digitalWrite(LED_RED, LOW); //power on red led
+            digitalWrite(LED_GREEN, HIGH);
+            digitalWrite(LED_BLUE, HIGH);
+            Serial.println("rec : hongse ");
+            break;
+        case 2:
+            digitalWrite(LED_GREEN, LOW); //power on green led
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_BLUE, HIGH);
+            Serial.println("rec : lvse ");
+            break;
+        case 3:
+            digitalWrite(LED_BLUE, LOW); //power on blue led
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_GREEN, HIGH);
+            Serial.println("rec : lanse ");
+            break;
+        case 4:
+            digitalWrite(LED_RED, HIGH);
+            digitalWrite(LED_GREEN, HIGH);
+            digitalWrite(LED_BLUE, HIGH);   //power off all leds
+            Serial.println("rec : guandeng ");
+        default:
+            break;
+        }
+    }else
+    {
+        Serial.println("recognize failed.");
+    }
+    delay(1000);
+}

libraries/Maix_Speech_Recognition/library.properties

@@ -0,0 +1,9 @@
+name=Maix_Speech_Recognition
+version=1.0
+author=BigBits
+maintainer=BigBits<bigbits@hackx.cc>
+sentence=Maix Boards Speech Recognition Lib
+paragraph=Maix Boards Speech Recognition Lib
+category=Uncategorized
+url=
+architectures=k210

libraries/Maix_Speech_Recognition/src/Maix_Speech_Recognition.cpp

@@ -0,0 +1,383 @@
+#include "Maix_Speech_Recognition.h"
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+#include "sysctl.h"
+#include "plic.h"
+#include "uarths.h"
+#include "util/g_def.h"
+#include "i2s.h"
+#include "fpioa.h"
+
+#include "util/VAD.h"
+#include "util/MFCC.h"
+#include "util/DTW.h"
+#include "util/flash.h"
+#include "util/ADC.h"
+
+#define USART1_printf Serial.printf
+
+uint16_t VcBuf[atap_len];
+atap_tag    atap_arg;
+valid_tag   valid_voice[max_vc_con];
+v_ftr_tag   ftr;
+v_ftr_tag   ftr_temp;
+v_ftr_tag   ftr_mdl_temp[10];
+v_ftr_tag   *pftr_mdl_temp[10];
+
+#define save_ok     0
+#define VAD_fail    1
+#define MFCC_fail   2
+#define Flash_fail  3
+
+#define FFT_N 512
+
+uint16_t rx_buf[FRAME_LEN];
+uint32_t g_rx_dma_buf[FRAME_LEN * 2];
+uint64_t fft_out_data[FFT_N / 2];
+
+volatile uint32_t g_index;
+volatile uint8_t uart_rec_flag;
+volatile uint32_t receive_char;
+volatile uint8_t i2s_rec_flag;
+volatile uint8_t i2s_start_flag = 0;
+
+int i2s_dma_irq(void *ctx)
+{
+    uint32_t i;
+    if(i2s_start_flag)
+    {
+        int16_t s_tmp;
+        if(g_index)
+        {
+            i2s_receive_data_dma(I2S_DEVICE_0, &g_rx_dma_buf[g_index], frame_mov * 2, DMAC_CHANNEL3);
+            g_index = 0;
+            for(i = 0; i < frame_mov; i++)
+            {
+                s_tmp = (int16_t)(g_rx_dma_buf[2 * i] & 0xffff); //g_rx_dma_buf[2 * i + 1] Low left
+                rx_buf[i] = s_tmp + 32768;
+            }
+            i2s_rec_flag = 1;
+        }
+        else
+        {
+            i2s_receive_data_dma(I2S_DEVICE_0, &g_rx_dma_buf[0], frame_mov * 2, DMAC_CHANNEL3);
+            g_index = frame_mov * 2;
+            for(i = frame_mov; i < frame_mov * 2; i++)
+            {
+                s_tmp = (int16_t)(g_rx_dma_buf[2 * i] & 0xffff);//g_rx_dma_buf[2 * i + 1] Low left
+                rx_buf[i] = s_tmp + 32768;
+            }
+            i2s_rec_flag = 2;
+        }
+    }
+    else
+    {
+        i2s_receive_data_dma(I2S_DEVICE_0, &g_rx_dma_buf[0], frame_mov * 2, DMAC_CHANNEL3);
+        g_index = frame_mov * 2;
+    }
+    return 0;
+}
+
+
+SpeechRecognizer::SpeechRecognizer(){
+
+}
+
+SpeechRecognizer::~SpeechRecognizer(){
+    
+}
+
+int
+SpeechRecognizer::begin()
+{
+    //io_mux_init
+    fpioa_set_function(20, FUNC_I2S0_IN_D0);
+    fpioa_set_function(18, FUNC_I2S0_SCLK);
+    fpioa_set_function(19, FUNC_I2S0_WS);
+
+    //i2s init
+    i2s_init(I2S_DEVICE_0, I2S_RECEIVER, 0x3);
+
+    i2s_rx_channel_config(I2S_DEVICE_0, I2S_CHANNEL_0,
+            RESOLUTION_16_BIT, SCLK_CYCLES_32,
+            TRIGGER_LEVEL_4, STANDARD_MODE);
+
+    i2s_set_sample_rate(I2S_DEVICE_0, 8000);
+
+    dmac_init();
+    dmac_set_irq(DMAC_CHANNEL3, i2s_dma_irq, NULL, 3);
+    i2s_receive_data_dma(I2S_DEVICE_0, &g_rx_dma_buf[0], frame_mov * 2, DMAC_CHANNEL3);
+
+    /* Enable the machine interrupt */
+    sysctl_enable_irq();
+    return 0;
+}
+
+int
+SpeechRecognizer::record(uint8_t keyword_num, uint8_t model_num)
+{
+    if (keyword_num > 10) return -1;
+    if (model_num > 4)    return -2;
+    
+    comm = keyword_num;
+    uint8_t prc_count = model_num;
+    uint32_t addr = 0;
+
+    g_index = 0;
+    i2s_rec_flag = 0;
+    i2s_start_flag = 1;
+    
+    addr = ftr_start_addr + comm * size_per_comm + prc_count * size_per_ftr;
+
+    if (save_mdl(VcBuf, addr) == save_ok) {
+        return 0;
+    }else{
+        return -3;
+    }
+
+}
+
+int
+SpeechRecognizer::recognize()
+{
+    u8 res;
+    u32 dis;
+
+    g_index = 0;
+    i2s_rec_flag = 0;
+    i2s_start_flag = 1;
+
+    res = spch_recg(VcBuf, &dis);
+    if(dis != dis_err) 
+        return res;
+    else
+        return -1;
+}
+
+int
+SpeechRecognizer::addVoiceModel(uint8_t keyword_num, uint8_t model_num, const int16_t *voice_model, uint16_t frame_num)
+{
+    ftr_save[keyword_num * 4 + model_num].save_sign = save_mask;
+    ftr_save[keyword_num * 4 + model_num].frm_num = frame_num;
+
+    for (int i = 0; i < (vv_frm_max * mfcc_num); i++)
+        ftr_save[keyword_num * 4 + model_num].mfcc_dat[i] = voice_model[i];
+    return 0;
+}
+    
+int
+SpeechRecognizer::print_model(uint8_t keyword_num, uint8_t model_num)
+{
+    Serial.printf("frm_num=%d\n", ftr_save[keyword_num*4 + model_num].frm_num);
+    for (int i = 0; i < (vv_frm_max * mfcc_num); i++) {
+        if (((i + 1) % 35) == 0)
+            Serial.printf("%d,\n", ftr_save[keyword_num*4 + model_num].mfcc_dat[i]);
+        else
+            Serial.printf("%d, ", ftr_save[keyword_num*4 + model_num].mfcc_dat[i]);
+    }
+    Serial.printf("\nprint model ok!\n");
+    return 0;
+}
+
+uint8_t SpeechRecognizer::save_mdl(uint16_t *v_dat, uint32_t addr)
+{
+    u16 i, num;
+    u16 frame_index;
+get_noise1:
+    frame_index = 0;
+    num = atap_len / frame_mov;
+    //wait for finish
+    while (1) {
+        while (i2s_rec_flag == 0)
+            continue;
+        if (i2s_rec_flag == 1) {
+            for (i = 0; i < frame_mov; i++)
+                v_dat[frame_mov * frame_index + i] = rx_buf[i];
+        } else {
+            for (i = 0; i < frame_mov; i++)
+                v_dat[frame_mov * frame_index + i] = rx_buf[i + frame_mov];
+        }
+        i2s_rec_flag = 0;
+        frame_index++;
+        if (frame_index >= num)
+            break;
+    }
+//  for(i = 0; i < atap_len; i++)
+//      Serial.printf("noise: %d\n", v_dat[i]);
+    noise_atap(v_dat, atap_len, &atap_arg);
+    if (atap_arg.s_thl > 10000) {
+        Serial.printf("get noise again...\n");
+        goto get_noise1;
+    }
+    Serial.printf("speeking...\n");
+//wait for finish
+    while (i2s_rec_flag == 0)
+        continue;
+    if (i2s_rec_flag == 1) {
+        for (i = 0; i < frame_mov; i++)
+            v_dat[i + frame_mov] = rx_buf[i];
+    } else {
+        for (i = 0; i < frame_mov; i++)
+            v_dat[i + frame_mov] = rx_buf[i + frame_mov];
+    }
+    i2s_rec_flag = 0;
+    while (1) {
+        while (i2s_rec_flag == 0)
+            continue;
+        if (i2s_rec_flag == 1) {
+            for (i = 0; i < frame_mov; i++) {
+                v_dat[i] = v_dat[i + frame_mov];
+                v_dat[i + frame_mov] = rx_buf[i];
+            }
+        } else {
+            for (i = 0; i < frame_mov; i++) {
+                v_dat[i] = v_dat[i + frame_mov];
+                v_dat[i + frame_mov] = rx_buf[i + frame_mov];
+            }
+        }
+        i2s_rec_flag = 0;
+        if (VAD2(v_dat, valid_voice, &atap_arg) == 1)
+            break;
+        if (receive_char == 's')
+            return MFCC_fail;
+    }
+//  if (valid_voice[0].end == ((void *)0)) {
+//      Serial.printf("VAD_fail\n");
+//      return VAD_fail;
+//  }
+
+    get_mfcc(&(valid_voice[0]), &ftr, &atap_arg);
+    if (ftr.frm_num == 0) {
+        //Serial.printf("MFCC_fail\n");
+        return MFCC_fail;
+    }
+//  ftr.word_num = valid_voice[0].word_num;
+    return save_ftr_mdl(&ftr, addr);
+//  ftr_mdl_temp[addr] = ftr;
+//  return save_ok;
+}
+
+uint8_t SpeechRecognizer::spch_recg(uint16_t *v_dat, uint32_t *mtch_dis)
+{
+        u16 i;
+    u32 ftr_addr;
+    u32 min_dis;
+    u16 min_comm;
+    u32 cur_dis;
+    v_ftr_tag *ftr_mdl;
+    u16 num;
+    u16 frame_index;
+    uint32_t cycle0, cycle1;
+
+get_noise2:
+    frame_index = 0;
+    num = atap_len / frame_mov;
+    //wait for finish
+    i2s_rec_flag = 0;
+    while (1) {
+        while (i2s_rec_flag == 0)
+            continue;
+        if (i2s_rec_flag == 1) {
+            for (i = 0; i < frame_mov; i++)
+                v_dat[frame_mov * frame_index + i] = rx_buf[i];
+        } else {
+            for (i = 0; i < frame_mov; i++)
+                v_dat[frame_mov * frame_index + i] = rx_buf[i + frame_mov];
+        }
+        i2s_rec_flag = 0;
+        frame_index++;
+        if (frame_index >= num)
+            break;
+    }
+    noise_atap(v_dat, atap_len, &atap_arg);
+    if (atap_arg.s_thl > 10000) {
+        Serial.printf("get noise again...\n");
+        goto get_noise2;
+    }
+
+    Serial.printf("speeking...\n");
+
+    //wait for finish
+    while (i2s_rec_flag == 0)
+        continue;
+    if (i2s_rec_flag == 1) {
+        for (i = 0; i < frame_mov; i++)
+            v_dat[i + frame_mov] = rx_buf[i];
+    } else {
+        for (i = 0; i < frame_mov; i++)
+            v_dat[i + frame_mov] = rx_buf[i + frame_mov];
+    }
+    i2s_rec_flag = 0;
+    while (1) {
+        while (i2s_rec_flag == 0)
+            continue;
+        if (i2s_rec_flag == 1) {
+            for (i = 0; i < frame_mov; i++) {
+                v_dat[i] = v_dat[i + frame_mov];
+                v_dat[i + frame_mov] = rx_buf[i];
+            }
+        } else {
+            for (i = 0; i < frame_mov; i++) {
+                v_dat[i] = v_dat[i + frame_mov];
+                v_dat[i + frame_mov] = rx_buf[i + frame_mov];
+            }
+        }
+        i2s_rec_flag = 0;
+        if (VAD2(v_dat, valid_voice, &atap_arg) == 1)
+            break;
+        if (receive_char == 's') {
+            *mtch_dis = dis_err;
+            Serial.printf("send 'c' to start\n");
+            return 0;
+        }
+    }
+    Serial.printf("vad ok\n");
+//  if (valid_voice[0].end == ((void *)0)) {
+//      *mtch_dis=dis_err;
+//      USART1_printf("VAD fail ");
+//      return (void *)0;
+//  }
+
+    get_mfcc(&(valid_voice[0]), &ftr, &atap_arg);
+    if (ftr.frm_num == 0) {
+        *mtch_dis = dis_err;
+        Serial.printf("MFCC fail ");
+        return 0;
+    }
+//  for (i = 0; i < ftr.frm_num * mfcc_num; i++) {
+//      if (i % 12 == 0)
+//          Serial.printf("\n");
+//      Serial.printf("%d ", ftr.mfcc_dat[i]);
+//  }
+//  ftr.word_num = valid_voice[0].word_num;
+    Serial.printf("mfcc ok\n");
+    i = 0;
+    min_comm = 0;
+    min_dis = dis_max;
+    cycle0 = read_csr(mcycle);
+    for (ftr_addr = ftr_start_addr; ftr_addr < ftr_end_addr; ftr_addr += size_per_ftr)  {
+    //  ftr_mdl=(v_ftr_tag*)ftr_addr;
+        ftr_mdl = (v_ftr_tag *)(&ftr_save[ftr_addr / size_per_ftr]);
+        cur_dis = ((ftr_mdl->save_sign) == save_mask) ? dtw(ftr_mdl, &ftr) : dis_err;
+        if ((ftr_mdl->save_sign) == save_mask) {
+            Serial.printf("no. %d, frm_num = %d, save_mask=%d", i + 1, ftr_mdl->frm_num, ftr_mdl->save_sign);
+            Serial.printf("cur_dis=%d\n", cur_dis);
+        }
+        if (cur_dis < min_dis) {
+            min_dis = cur_dis;
+            min_comm = i + 1;
+        }
+        i++;
+    }
+    cycle1 = read_csr(mcycle) - cycle0;
+    Serial.printf("[INFO] recg cycle = 0x%08x\n", cycle1);
+    if (min_comm % 4)
+        min_comm = min_comm / ftr_per_comm + 1;
+    else
+        min_comm = min_comm / ftr_per_comm;
+    //USART1_printf("recg end ");
+    *mtch_dis = min_dis;
+    return (u8)min_comm;//(commstr[min_comm].str);
+}

libraries/Maix_Speech_Recognition/src/Maix_Speech_Recognition.h

@@ -0,0 +1,43 @@
+#ifndef __MAIX_SPEECH_RECOGNITION_H
+#define __MAIX_SPEECH_RECOGNITION_H
+
+#include "Arduino.h"
+
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+
+#include "sysctl.h"
+#include "plic.h"
+#include "uarths.h"
+#include "util/g_def.h"
+#include "i2s.h"
+
+#include "util/VAD.h"
+#include "util/MFCC.h"
+#include "util/DTW.h"
+#include "util/flash.h"
+#include "util/ADC.h"
+
+
+class SpeechRecognizer{
+public:
+    SpeechRecognizer();
+    ~SpeechRecognizer();
+    int begin();    //初始化i2s
+    int record(uint8_t keyword_num, uint8_t model_num);  //记录关键词 
+    int recognize();  //识别，返回关键词号
+    int addVoiceModel(uint8_t keyword_num, uint8_t model_num, const int16_t *voice_model, uint16_t frame_num);
+    int print_model(uint8_t keyword_num, uint8_t model_num);
+private:
+    uint8_t save_mdl(uint16_t *v_dat, uint32_t addr);
+    uint8_t spch_recg(uint16_t *v_dat, uint32_t *mtch_dis);
+
+private:
+    uint8_t comm; //关键词号
+    
+
+};
+
+#endif

libraries/Maix_Speech_Recognition/src/util/ADC.h

@@ -0,0 +1,22 @@
+#ifndef _ADC_H
+#define _ADC_H
+
+
+#define fs			8000					//ADC采样率 Hz 8000
+#define	voice_len	3000					//录音时间长度 单位ms
+#define	VcBuf_Len	((fs/1000)*voice_len)	//语音缓存区长度 单位点数 每个采样点16位
+#define atap_len_t	300						//背景噪音自适应时间长度 ms
+#define atap_len	((fs/1000)*atap_len_t)	//背景噪音自适应长度
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+void ADC_DMA_Init(void);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+

libraries/Maix_Speech_Recognition/src/util/DTW.c

@@ -0,0 +1,434 @@
+/*******       DTW.C         ********/
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <math.h>
+#include "g_def.h"
+#include "ADC.h"
+#include "VAD.h"
+#include "MFCC.h"
+#include "DTW.h"
+
+/*
+ *	DTW算法 通过局部优化的方法实现加权距离总和最小
+
+	时间规整函数：
+	C={c(1),c(2),…,c(N)}
+	N为路径长度，c(n)=(i(n),j(n))表示第n个匹配点是有参考模板的
+第i(n)个特征矢量与待测模板的第j(n)个特征矢量构成的匹配点对，两
+者之间的距离d(x(i(n)),y(j(n)))称为匹配距离。
+	时间规整函数满足一下约束：
+	1.单调性，规整函数单调增加。
+	2.起点终点约束，起点对起点，终点对终点。
+	3.连续性，不允许跳过任何一点。
+	4.最大规整量不超过某一极限值。|i(n)-j(n)|<M,M为窗宽。规整
+函数所处的区域位于平行四边形内。局部路径约束，用于限制当第n步
+为(i(n),j(n))时，前几步存在几种可能的路径。
+
+	DTW步骤：
+	1.初始化。令i(0)=j(0)=0,i(N)=in_frm_num,j(N)=mdl_frm_num.
+确定一个平行四边形，有两个位于(0,0)和(in_frm_num,mdl_frm_num)的顶点，相邻斜边斜
+率分别是2和1/2.规整函数不可超出此平行四边形。
+	2.递推求累计距离。
+
+	若输入特征与特征模板的帧数差别过大，直接将匹配距离设为最大
+	frm_in_num<(frm_mdl_num/2)||frm_in_num>(frm_mdl_num*2)
+*/
+int64_t avr_in[mfcc_num];
+int64_t avr_mdl[mfcc_num];
+
+int64_t standard_in[mfcc_num];
+int64_t standard_mdl[mfcc_num];
+int dtw_data[vv_frm_max*vv_frm_max];
+
+struct pointOritation//节点方向，用来回溯每个W点
+{
+	int frontI, frontJ;
+};
+int g[vv_frm_max][vv_frm_max];
+struct pointOritation pOritation[vv_frm_max][vv_frm_max];//用来存放
+
+void gArray(int *p, int n, int m, int *g, struct pointOritation *pr)
+{
+	int i = 0, j = 0;
+
+	*g = (*p) * 2;//起始点（最左上角的点）
+	for (i = 1; i < m; i++) {//最上面一横
+		*(g + i) =  *(g + i - 1) + *(p + i);
+		(pr + i)->frontI = 0;
+		(pr + i)->frontJ = i - 1;
+	}
+
+	for (i = 1; i < n; i++) {//最左边的一竖
+		*(g+i*m+0) =  *(g+(i-1)*m+0)+(*(p+i*m+0));
+		(pr+i*m+0)->frontI = i-1;
+		(pr+i*m+0)->frontJ = 0;
+	}
+
+    //计算剩余网格的G值
+	for (i = 1; i < n; i++) {
+		for (j = 1; j < m; j++) {
+			int left, up, incline;
+
+			left = *(g + i*m+j-1) + *(p + i * m + j);
+			up = *(g + (i - 1) * m + j) + *(p + i * m + j);
+			incline = *(g + (i - 1) * m + j - 1) + (*(p + i * m + j)) * 2;
+
+	    //从左、上、斜三个方向选出最小的
+			int min = left;
+
+			*(g + i * m + j) = min;
+			(pr + i * m + j)->frontI = i;
+			(pr + i * m + j)->frontJ = j - 1;
+
+			if (min > up) {
+				min = up;
+				*(g + i * m + j) = min;
+				(pr + i * m + j)->frontI = i - 1;
+				(pr + i * m + j)->frontJ = j;
+			}
+			if (min > incline) {
+				min = incline;
+				*(g + i * m + j) = min;
+				(pr + i * m + j)->frontI = i - 1;
+				(pr + i * m + j)->frontJ = j - 1;
+			}
+		}
+	}
+#if 0
+    //输出G数组
+	for (i = 0; i < n; i++) {
+		for (j = 0; j < m; j++)
+			printf("%d, ", *(g+i*m+j));
+		printf("\n");
+	}
+	//输出方向数组
+	for (i = 0; i < n; i++) {
+		for (j = 0; j < m; j++)
+			printf("(%d,%d), ", (pr+i*m+j)->frontI, (pr+i*m+j)->frontJ);
+		printf("\n");
+	}
+   #endif
+}
+int printPath(struct pointOritation *po, int n, int m, int *g)
+{
+    //从最后一个点向前输出路径节点
+	int i = n-1, j = m - 1;
+	int step = 0;
+
+	while (1) {
+		int ii = (po + i * m + j)->frontI, jj = (po + i * m + j)->frontJ;
+
+		if (i == 0 && j == 0)
+			break;
+ //       printf("(%d,%d):%d\n",i,j,*(g+i*m+j));
+		i = ii;
+		j = jj;
+		step++;
+	}
+ //   printf("distance1 = %d\n", *(g+(n-1)*m + m -1) / step);
+	return step;
+	//printf("distance = %d\n", *(g+(n-1)*m + m -1) / step);
+}
+
+/*
+ *	获取两个特征矢量之间的距离
+	参数
+	frm_ftr1	特征矢量1
+	frm_ftr2	特征矢量2
+	返回值
+	dis			矢量距离
+*/
+u32 get_dis(s16 *frm_ftr1, s16 *frm_ftr2)
+{
+	u8	i;
+
+#if 0
+	#if 1
+	u32	dis;
+	s32 dif;	//两矢量相同维度上的差值
+
+	dis = 0;
+	for (i = 0; i < mfcc_num; i++) {
+		//USART1_printf("dis=%d ",dis);
+		dif = frm_ftr1[i]-frm_ftr2[i];
+		dis += (dif*dif);
+	}
+	//USART1_printf("dis=%d ",dis);
+	dis = sqrtf(dis);
+	//USART1_printf("%d\r\n",dis);
+	return dis;
+	#else
+	u32	dis;
+	s32 dif;
+	s32 avr;
+
+	dis = 0;
+	for (i = 0; i < mfcc_num; i++) {
+		//USART1_printf("dis=%d ",dis);
+		avr = (frm_ftr1[i]+frm_ftr2[i]) / 2;
+		dif = sqrtf((frm_ftr1[i] - avr) * (frm_ftr1[i] - avr) + (frm_ftr2[i] - avr) * (frm_ftr2[i] - avr));
+
+		dif = (frm_ftr1[i]-frm_ftr2[i]) * 100 / dif;
+
+		dis += (dif*dif);
+	}
+	//USART1_printf("dis=%d ",dis);
+	dis = sqrtf(dis);
+	//USART1_printf("%d\r\n",dis);
+	return dis;
+	#endif
+#else
+	#if 1
+	int64_t dif = 0;
+	int64_t dif_a = 0;
+	int64_t dif_b = 0;
+	int32_t dif_r = 0;
+
+	for (i = 0; i < mfcc_num; i++) {
+		dif += (frm_ftr1[i]*frm_ftr2[i]);
+
+		dif_a += (frm_ftr1[i] * frm_ftr1[i]);
+		dif_b += (frm_ftr2[i] * frm_ftr2[i]);
+	}
+	dif_r = 1000 - (dif * 1000 / sqrt(dif_a * dif_b));
+
+	return dif_r;
+	#else
+	int64_t dif = 0;
+	int64_t dif_a = 0;
+	int64_t dif_b = 0;
+	int32_t dif_r = 0;
+
+	for (i = 0; i < mfcc_num; i++) {
+		dif += ((frm_ftr1[i] - avr_mdl[i]) * (frm_ftr2[i] - avr_in[i]));
+		dif_a += ((frm_ftr1[i] - avr_mdl[i]) * (frm_ftr1[i] - avr_mdl[i]));
+		dif_b += ((frm_ftr2[i] - avr_in[i]) * (frm_ftr2[i] - avr_in[i]));
+	}
+	dif_r = 1000 - (dif * 1000 / (sqrt(dif_a * dif_b)));
+
+	return dif_r;
+	#endif
+
+#endif
+}
+
+//平行四边形两外两顶点 X坐标值
+static u16	X1;			//上边交点
+static u16	X2;			//下边交点
+static int	in_frm_num;	//输入特征帧数
+static int	mdl_frm_num;//特征模板帧数
+
+#define ins		0
+#define outs	1
+
+/*
+ *	范围控制
+
+*/
+u8 dtw_limit(u16 x, u16 y)
+{
+	if (x < X1) {
+		if (y >= ((2*x)+2))
+			return outs;
+	} else {
+		if ((2*y+in_frm_num-2*mdl_frm_num) >= (x+4))
+			return outs;
+	}
+
+	if (x < X2) {
+		if ((2*y+2) <= x)
+			return outs;
+	} else {
+		if ((y+4) <= (2*x+mdl_frm_num-2*in_frm_num))
+			return outs;
+	}
+
+	return ins;
+}
+
+/*
+ *	DTW 动态时间规整
+	参数
+	ftr_in	:输入特征值
+	ftr_mdl	:特征模版
+	返回值
+	dis		:累计匹配距离
+*/
+
+u32 dtw(v_ftr_tag *ftr_in, v_ftr_tag *frt_mdl)
+{
+	u32 dis;
+//	u16 x, y;
+	u16 step;
+	s16 *in;
+	s16 *mdl;
+//	u32 d_right_up, right, right_up; //up,
+//	u32 min;
+	int i, j;
+
+	in_frm_num = ftr_in->frm_num;
+	mdl_frm_num = frt_mdl->frm_num;
+
+	if ((in_frm_num > (mdl_frm_num*3)) || ((3*in_frm_num) < mdl_frm_num)) {
+		//USART1_printf("in_frm_num=%d mdl_frm_num=%d\r\n", in_frm_num,mdl_frm_num);
+		return dis_err;
+	} else {
+		// 计算约束平行四边形顶点值
+		X1 = (2*mdl_frm_num-in_frm_num)/3;
+		X2 = (4*in_frm_num-2*mdl_frm_num)/3;
+		in = ftr_in->mfcc_dat;
+		mdl = frt_mdl->mfcc_dat;
+#if 0
+		for (j = 0; j < mfcc_num; j++) {
+			avr_in[j] = 0;
+			avr_mdl[j] = 0;
+		}
+
+		for (j = 0; j < mfcc_num; j++)
+			for (i = 0; i < in_frm_num; i++)
+				avr_in[j] += in[mfcc_num * i + j];
+		for (j = 0; j < mfcc_num; j++)
+			avr_in[j] = avr_in[j] / in_frm_num;
+//
+		for (j = 0; j < mfcc_num; j++)
+			for (i = 0; i < mdl_frm_num; i++)
+				avr_mdl[j] += mdl[mfcc_num * i + j];
+		for (j = 0; j < mfcc_num; j++)
+			avr_mdl[j] = avr_mdl[j] / mdl_frm_num;
+
+		dis = get_dis(in, mdl);
+		x = 1;
+		y = 1;
+		step = 1;
+#endif
+#if 0
+		for (i = 0; i < in_frm_num; i++) {
+			for (j = 0; j < mdl_frm_num; j++) {
+				printf("%d,", get_dis(mdl, in));
+				mdl += mfcc_num;
+			}
+			mdl = frt_mdl->mfcc_dat;
+			in += mfcc_num;
+			printf("\n");
+		}
+		in = ftr_in->mfcc_dat;
+		mdl = frt_mdl->mfcc_dat;
+#endif
+		for (i = 0; i < in_frm_num; i++) {
+			for (j = 0; j < mdl_frm_num; j++) {
+				//dtw_data[i][j] = get_dis(in + (i * mfcc_num), mdl + (j * mfcc_num));
+				//dtw_data[i][j] = get_dis(in, mdl);
+				*(dtw_data+i*mdl_frm_num+j) = get_dis(in, mdl);
+			//	printf("%d,", dtw_data[i*mdl_frm_num+j]);
+				mdl += mfcc_num;
+			}
+			//printf("\n");
+			mdl = frt_mdl->mfcc_dat;
+			in += mfcc_num;
+		}
+		gArray(dtw_data, in_frm_num, mdl_frm_num, *g, *pOritation);
+		step = printPath(*pOritation, in_frm_num, mdl_frm_num, *g);
+		//printf("step=%d\r\n",step);
+		dis = *((int *)g+(in_frm_num-1)*mdl_frm_num + mdl_frm_num - 1);
+//		printf("dis=%d step=%d dis/step=%d\r\n",dis,step,dis/step);
+		}
+	return (dis/step); //步长归一化
+}
+
+
+void get_mean(s16 *frm_ftr1, s16 *frm_ftr2, s16 *mean)
+{
+	u8	i;
+
+	for (i = 0; i < mfcc_num; i++) {
+		mean[i] = (frm_ftr1[i]+frm_ftr2[i])/2;
+	//	printf("x=%d y=%d ", frm_ftr1[i], frm_ftr2[i]);
+	//	printf("mean=%d\r\n", mean[i]);
+	}
+}
+
+/*
+ *	从两特征矢量获取特征模板
+	参数
+	ftr_in1	:输入特征值
+	ftr_in2	:输入特征值
+	ftr_mdl	:特征模版
+	返回值
+	dis		:累计匹配距离
+*/
+
+u32 get_mdl(v_ftr_tag *ftr_in1, v_ftr_tag *ftr_in2, v_ftr_tag *ftr_mdl)
+{
+	u32 dis;
+	u16 x, y;
+	u16 step;
+	s16 *in1;
+	s16 *in2;
+	s16 *mdl;
+	u32 right, right_up, d_right_up;//up,
+	u32 min;
+
+	in_frm_num = ftr_in1->frm_num;
+	mdl_frm_num = ftr_in2->frm_num;
+
+	if ((in_frm_num > (mdl_frm_num*2)) || ((2*in_frm_num) < mdl_frm_num)) {
+		printf("in_frm_num= %d, mdl_frm_num= %d\n", in_frm_num, mdl_frm_num);
+		return dis_err;
+	} else {
+		// 计算约束平行四边形顶点值
+		X1 = (2*mdl_frm_num-in_frm_num)/3;
+		X2 = (4*in_frm_num-2*mdl_frm_num)/3;
+		in1 = ftr_in1->mfcc_dat;
+		in2 = ftr_in2->mfcc_dat;
+		mdl = ftr_mdl->mfcc_dat;
+
+		dis = get_dis(in1, in2);
+		get_mean(in1, in2, mdl);
+		x = 1;
+		y = 1;
+		step = 1;
+		do {
+			//up = (dtw_limit(x, y+1) == ins)?get_dis(in2+mfcc_num, in1):dis_err;
+			d_right_up = (dtw_limit(x+1, y+2) == ins)?get_dis(in2+mfcc_num+mfcc_num, in1+mfcc_num):dis_err;
+			right = (dtw_limit(x+1, y) == ins)?get_dis(in2, in1+mfcc_num):dis_err;
+			right_up = (dtw_limit(x+1, y+1) == ins)?get_dis(in2+mfcc_num, in1+mfcc_num):dis_err;
+
+			min = right_up;
+			if (min > right)
+				min = right;
+
+			if (min > d_right_up)
+				min = d_right_up;
+
+			dis += min;
+
+			if (min == right_up) {
+				in1 += mfcc_num;
+				x++;
+				in2 += mfcc_num;
+				y++;
+			} else if (min == d_right_up) {
+				//in2 += mfcc_num;
+				//y++;
+				in2 = in2 + mfcc_num + mfcc_num;
+				y += 2;
+				in1 += mfcc_num;
+				x++;
+			} else {
+				in1 += mfcc_num;
+				x++;
+			}
+			step++;
+
+			mdl += mfcc_num;
+			get_mean(in1, in2, mdl);
+
+		//	printf("x=%d y=%d\r\n", x, y);
+		} while ((x < in_frm_num) && (y < mdl_frm_num));
+		printf("step=%d\r\n", step);
+		ftr_mdl->frm_num = step;
+	}
+	return (dis/step); //步长归一化
+}
+

libraries/Maix_Speech_Recognition/src/util/DTW.h

@@ -0,0 +1,20 @@
+#ifndef _DTW_H
+#define _DTW_H
+#include "g_def.h"
+
+#define dis_err	0xFFFFFFFF
+#define dis_max	0xFFFFFFFF
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+u32 dtw(v_ftr_tag *ftr_in, v_ftr_tag *frt_mdl);
+u32 get_mdl(v_ftr_tag *ftr_in1, v_ftr_tag *ftr_in2, v_ftr_tag *ftr_mdl);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/Maix_Speech_Recognition/src/util/FIR.c

@@ -0,0 +1,37 @@
+#include <stdio.h>
+#include "FIR.h"
+
+const double Gains[39] = {
+-0.01152483856464,  -0.0225638929287, -0.002300804134165,  0.01259363093284,
+-0.0003113695305127, -0.01591961043518, 0.005297252625722,  0.01846679452201,
+-0.01074864266549, -0.02187510941784,   0.0192688121099,  0.02485021814652,
+-0.03198920030056, -0.02754770718169,  0.05351978821001,   0.0296026126381,
+-0.09977798297944, -0.03089664322888,   0.3161729116138,   0.5313543998522,
+0.3161729116138, -0.03089664322888, -0.09977798297944,   0.0296026126381,
+0.05351978821001, -0.02754770718169, -0.03198920030056,  0.02485021814652,
+0.0192688121099, -0.02187510941784, -0.01074864266549,  0.01846679452201,
+0.005297252625722, -0.01591961043518, -0.0003113695305127,  0.01259363093284,
+-0.002300804134165,  -0.0225638929287, -0.01152483856464
+};
+#define ORDER        38                       //阶数
+
+double Buffer[ORDER + 1];        //采样历史数据
+
+double Fir(double Input)
+{
+	double Output = 0.0;        //数据输出
+	int Index;                //下标索引
+
+	//采样数据移位
+	for (Index = ORDER; Index > 0; Index--)
+		Buffer[Index] = Buffer[Index-1];
+
+	Buffer[0] = Input;
+
+	//计算输出
+	for (Index = 0; Index < ORDER+1; Index++)
+		Output += Gains[Index]*Buffer[Index];
+
+	return Output;
+}
+

libraries/Maix_Speech_Recognition/src/util/FIR.h

@@ -0,0 +1,15 @@
+#ifndef _FIR_H_
+#define _FIR_H_
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+double Fir(double Input);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/Maix_Speech_Recognition/src/util/MFCC.c

@@ -0,0 +1,273 @@
+/*******   MFCC.C    *******/
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+#include "g_def.h"
+#include <math.h>
+#include "ADC.h"
+#include "VAD.h"
+#include "MFCC.h"
+#include "MFCC_Arg.h"
+#include <float.h>
+#include "sysctl.h"
+#include "dmac.h"
+#include "fft.h"
+#include "FIR.h"
+
+void cr4_fft_1024_stm32(void *pssOUT, void *pssIN, u16 Nbin);
+void normalize(s16 *mfcc_p, u16 frm_num);
+
+u32 fft_out[mfcc_fft_point];
+s16 fft_in[mfcc_fft_point];
+
+extern uint64_t fft_out_data[512 / 2];
+extern void fft_dma_init(void);
+extern volatile fft_t *const fft;
+
+void fft_input_intdata(int16_t *data, uint8_t point)
+{
+    uint16_t point_num = 0;
+    uint16_t i;
+    fft_data_t input_data;
+
+    if (point == 0)
+        point_num = 512;
+    else if (point == 1)
+        point_num = 256;
+    else if (point == 2)
+        point_num = 128;
+    else if (point == 3)
+        point_num = 64;
+    point_num = point_num / 2;  // one time send two data
+
+    for (i = 0; i < point_num; i++) {
+        input_data.R1 = data[2 * i];
+        input_data.I1 = 0;
+        input_data.R2 = data[2 * i + 1];
+        input_data.I2 = 0;
+
+        fft->fft_input_fifo.fft_input_fifo = *(uint64_t *)&input_data;
+    }
+}
+
+void fft_sync_data(int16_t *data, uint8_t point, fft_data_t *fft_data)
+{
+    uint16_t point_num = 0;
+    uint16_t i;
+
+    if (point == 0)
+        point_num = 512;
+    else if (point == 1)
+        point_num = 256;
+    else if (point == 2)
+        point_num = 128;
+    else if (point == 3)
+        point_num = 64;
+    point_num = point_num / 2;  // one time send two data
+
+    for (i = 0; i < point_num; i++) {
+        (fft_data + i)->R1 = data[2 * i];
+        (fft_data + i)->I1 = 0;
+        (fft_data + i)->R2 = data[2 * i + 1];
+        (fft_data + i)->I2 = 0;
+    }
+}
+
+
+/*
+ *  cr4_fft_1024_stm32输入参数是有符号数
+ *
+ *  cr4_fft_1024_stm32输入参数包括实数和虚数
+    但语音数据只包括实数部分 虚数用0填充
+    fft点数超出输入数据长度时 超过部分用0填充
+
+    cr4_fft_1024_stm32输出数据包括实数和虚数
+    应该取其绝对值 即平方和的根
+ */
+
+u32 *mfcc_fft(s16 *dat_buf, u16 buf_len)
+{
+    u16 i;
+    s32 real, imag;
+    fft_data_t output_data;
+
+    if (buf_len > mfcc_fft_point)
+        return (void *)0;
+
+    for (i = 0; i < buf_len; i++) {
+        fft_in[i] =  *(dat_buf+i);//虚部高位 实部低位
+    }
+    for (; i < mfcc_fft_point; i++)
+        fft_in[i] = 0;//超出部分用0填充
+
+    fft_data_t fft_in_buf[512];
+    memset(fft_in_buf, 0 , sizeof(fft_in_buf));
+    fft_sync_data(fft_in, FFT_512, fft_in_buf);
+    fft_complex_uint16_dma(DMAC_CHANNEL0, DMAC_CHANNEL1, 0x1ff, FFT_DIR_FORWARD, (uint64_t *)fft_in_buf, 512, fft_out_data);
+
+    for (i = 0; i < frq_max / 2; i++) {
+        output_data = *(fft_data_t *)&fft_out_data[i];
+        imag = (s16)output_data.I1;
+        real = (s16)output_data.R1;
+        real = real*real+imag*imag;
+        fft_out[2 * i] = sqrtf((float)real)*10;
+
+        imag = (s16)output_data.I2;
+        real = (s16)output_data.R2;
+
+        real = real*real+imag*imag;
+        fft_out[2 * i + 1] = sqrtf((float)real)*10;
+    }
+    return fft_out;
+}
+
+/*  MFCC：Mel频率倒谱系数
+ *
+    参数：
+    valid   有效语音段起点终点
+
+    返回值：
+    v_ftr   MFCC值，帧数
+
+    Mel=2595*lg(1+f/700)
+    1000Hz以下按线性刻度 1000Hz以上按对数刻度
+    三角型滤波器中心频率 在Mel频率刻度上等间距排列
+    预加重:6dB/倍频程 一阶高通滤波器  H(z)=1-uz^(-1) y(n)=x(n)-ux(n-1) u=0.94~0.97
+
+    MFCC 步骤：
+    1.对语音信号预加重、分帧、加汉明窗处理，然后进行短时傅里叶变换，得出频谱
+    2.取频谱平方，得能量谱。并用24个Mel带通滤波器进行滤波，输出Mel功率谱
+    3.对每个滤波器的输出值取对数，得到相应频带的对数功率谱。然后对24个对数功率进行
+      反离散余弦变换得到12个MFCC系数
+*/
+
+void get_mfcc(valid_tag *valid, v_ftr_tag *v_ftr, atap_tag *atap_arg)
+{
+    u16 *vc_dat;
+    u16 h, i;
+    u32 *frq_spct;          //频谱
+    s16 vc_temp[FRAME_LEN]; //语音暂存区
+    s32 temp;
+
+    u32 pow_spct[tri_num];  //三角滤波器输出对数功率谱
+    u16 frm_con;
+    s16 *mfcc_p;
+    s8  *dct_p;
+    s32 mid;
+    u16 v_frm_num;
+
+    //USART1_printf("start=%d end=%d",(u32)(valid->start),(u32)(valid->end));
+    v_frm_num = (((u32)(valid->end)-(u32)(valid->start))/2-FRAME_LEN)/(FRAME_LEN-frame_mov)+1;
+    if (v_frm_num > vv_frm_max) {
+        printf("frm_num=%d ", v_frm_num);
+        v_ftr->frm_num = 0;
+    } else {
+        mid = (s32)atap_arg->mid_val;
+        mfcc_p = v_ftr->mfcc_dat;
+        frm_con = 0;
+        //low pass filter
+    //  for (vc_dat = (u16 *)(valid->start); vc_dat <= ((u16 *)(valid->end-FRAME_LEN)); vc_dat += 1) {
+    //      *vc_dat = (u16)(Fir(*vc_dat));
+
+    //  }
+        for (vc_dat = (u16 *)(valid->start); vc_dat <= ((u16 *)(valid->end-FRAME_LEN)); vc_dat += (FRAME_LEN-frame_mov)) {
+            for (i = 0; i < FRAME_LEN; i++) {
+                //预加重
+            //  printf("vc_dat[%d]=%d ",i,((s32)(*(vc_dat+i))-mid));
+                temp = ((s32)(*(vc_dat+i))-mid) - hp_ratio(((s32)(*(vc_dat+i-1))-mid));
+            //  printf("vc_hp[%d]=%d ",i,temp);
+                //加汉明窗 并放大10倍
+                vc_temp[i] = (s16)(temp*hamm[i]/(hamm_top/10));
+            //  printf("vc_hm[%d]=%d\r\n",i,vc_temp[i]);
+            }
+
+            frq_spct = mfcc_fft(vc_temp, FRAME_LEN);
+
+            for (i = 0; i < frq_max; i++) {
+                //printf("frq_spct[%d]=%d ",i,frq_spct[i]);
+                frq_spct[i] *= frq_spct[i];//能量谱
+                //printf("E_spct[%d]=%d\r\n",i,frq_spct[i]);
+            }
+
+            //加三角滤波器
+            pow_spct[0] = 0;
+            for (i = 0; i < tri_cen[1]; i++)
+                pow_spct[0] += (frq_spct[i]*tri_even[i]/(tri_top/10));
+            for (h = 2; h < tri_num; h += 2) {
+                pow_spct[h] = 0;
+                for (i = tri_cen[h-1]; i < tri_cen[h+1]; i++)
+                    pow_spct[h] += (frq_spct[i]*tri_even[i]/(tri_top/10));
+            }
+
+            for (h = 1; h < (tri_num-2); h += 2) {
+                pow_spct[h] = 0;
+                for (i = tri_cen[h-1]; i < tri_cen[h+1]; i++)
+                    pow_spct[h] += (frq_spct[i]*tri_odd[i]/(tri_top/10));
+            }
+            pow_spct[tri_num-1] = 0;
+            for (i = tri_cen[tri_num-2]; i < (mfcc_fft_point/2); i++)
+                pow_spct[tri_num-1] += (frq_spct[i]*tri_odd[i]/(tri_top/10));
+
+            //三角滤波器输出取对数
+            for (h = 0; h < tri_num; h++) {
+                //USART1_printf("pow_spct[%d]=%d ",h,pow_spct[h]);
+                pow_spct[h] = (u32)(log(pow_spct[h])*100);//取对数后 乘100 提升数据有效位数
+                //USART1_printf("%d\r\n",pow_spct[h]);
+            }
+
+            //反离散余弦变换
+            dct_p = (s8 *)dct_arg;
+            for (h = 0; h < mfcc_num; h++) {
+                mfcc_p[h] = 0;
+                for (i = 0; i < tri_num; i++)
+                    mfcc_p[h] += (((s32)pow_spct[i])*((s32)dct_p[i])/100);
+                //printf("%d,",mfcc_p[h]);
+                dct_p += tri_num;
+            }
+            //USART1_printf("\r\n");
+            mfcc_p += mfcc_num;
+            frm_con++;
+        }
+        mfcc_p = v_ftr->mfcc_dat;
+        normalize(mfcc_p, frm_con);
+        v_ftr->frm_num = frm_con;
+    }
+}
+
+s16 avg(s16 *mfcc_p, u16 frm_num)
+{
+    int i, j;
+    double sum = 0.0f;
+
+    printf("frm_num = %d, mfcc_num = %d\n", frm_num, mfcc_num);
+    for (i = 0; i < frm_num; i++)
+        for (j = 0; j < mfcc_num; j++) {
+            sum += mfcc_p[i * mfcc_num + j];
+//          printf("[%d, %d]%f %f ", i, j, sum, mfcc_p[i * mfcc_num + j]);
+        }
+    return (s16)(sum / (frm_num * mfcc_num));
+}
+
+s16 stdev(s16 *mfcc_p, s16 avg1, u16 frm_num)
+{
+    int i, j;
+    double sum = 0.0f;
+
+    for (i = 0; i < frm_num; i++)
+        for (j = 0; j < mfcc_num; j++)
+            sum += (mfcc_p[i * mfcc_num + j] - avg1) * (mfcc_p[i * mfcc_num + j] - avg1);
+    return (s16)(sqrt(sum / (frm_num * mfcc_num)));
+}
+
+void normalize(s16 *mfcc_p, u16 frm_num)
+{
+    int i, j;
+    s16 avg1 = avg(mfcc_p, frm_num);
+    s16 stdev1 = stdev(mfcc_p, avg1, frm_num);
+
+    printf("avg1 = %d, stdev1 = %d\n", avg1, stdev1);
+    for (i = 0; i < frm_num; i++)
+        for (j = 0; j < mfcc_num; j++)
+            mfcc_p[i * mfcc_num + j] = (mfcc_p[i * mfcc_num + j] - avg1) * 100 / stdev1;
+}

libraries/Maix_Speech_Recognition/src/util/MFCC.h

@@ -0,0 +1,39 @@
+#ifndef _MFCC_H
+#define _MFCC_H
+#include "VAD.h"
+#include "g_def.h"
+
+#define hp_ratio(x)	(x*95/100)//预加重系数 0.95
+#define mfcc_fft_point	512			//FFT点数
+#define frq_max		(mfcc_fft_point/2)	//最大频率
+#define hamm_top	10000			//汉明窗最大值
+#define	tri_top		1000			//三角滤波器顶点值
+#define tri_num		24				//三角滤波器个数
+//#define tri_num		17				//三角滤波器个数
+#define mfcc_num	12				//MFCC阶数
+
+#define vv_tim_max	2200	//单段有效语音最长时间 ms
+#define vv_frm_max	((vv_tim_max-frame_time)/(frame_time-frame_mov_t)+1)	//单段有效语音最长帧数
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+//#pragma pack(4)
+typedef struct {
+	u16 save_sign;						//存储标记 用于判断flash中特征模板是否有效
+	u16 frm_num;						//帧数
+//	u8 word_num;
+	s16 mfcc_dat[vv_frm_max*mfcc_num];	//MFCC转换结果
+//	float mfcc_dat[vv_frm_max*mfcc_num];
+} v_ftr_tag;								//语音特征结构体
+//#pragma pack()
+
+void get_mfcc(valid_tag *valid, v_ftr_tag *v_ftr, atap_tag *atap_arg);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/Maix_Speech_Recognition/src/util/MFCC_Arg.h

@@ -0,0 +1,135 @@
+#ifndef	MFCC_Arg
+#define	MFCC_Arg
+#include "g_def.h"
+
+//汉明窗 窗长160
+const u16 hamm[] = {
+
+800, 804, 814, 832, 857, 889, 929, 975, 1028, 1088, 1155, 1228, 1308, 1394, 1486, 1585, 1689, 1800, 1915, 2037,
+2163, 2295, 2432, 2573, 2718, 2868, 3022, 3179, 3340, 3504, 3671, 3841, 4013, 4187, 4364, 4542, 4721, 4901, 5082,
+5264, 5445, 5627, 5808, 5989, 6169, 6348, 6525, 6700, 6873, 7044, 7213, 7378, 7541, 7700, 7856, 8007, 8155, 8298,
+8437, 8571, 8701, 8825, 8943, 9056, 9164, 9265, 9361, 9450, 9533, 9610, 9680, 9743, 9799, 9849, 9892, 9927, 9956,
+9978, 9992, 9999, 9999, 9992, 9978, 9956, 9927, 9892, 9849, 9799, 9743, 9680, 9610, 9533, 9450, 9361, 9265, 9164,
+9056, 8943, 8825, 8701, 8571, 8437, 8298, 8155, 8007, 7856, 7700, 7541, 7378, 7213, 7044, 6873, 6700, 6525, 6348,
+6169, 5989, 5808, 5627, 5445, 5264, 5082, 4901, 4721, 4542, 4364, 4187, 4013, 3841, 3671, 3504, 3340, 3179, 3022,
+2868, 2718, 2573, 2432, 2295, 2163, 2037, 1915, 1800, 1689, 1585, 1486, 1394, 1308, 1228, 1155, 1088, 1028, 975,
+929, 889, 857, 832, 814, 804, 800
+};
+
+#if 0  //1024 point fft
+//三角滤波器中心频率点
+const u16 tri_cen[] = {
+
+11, 22, 33, 44, 55, 66, 77, 88, 99, 110, 121, 134, 152, 171, 191, 214, 237, 263, 291, 321, 354, 389, 427, 468
+};
+
+//奇数三角滤波器首尾相连的折线
+const u16 tri_odd[] = {
+
+0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545,
+455, 364, 273, 182, 91, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455,
+364, 273, 182, 91, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364,
+273, 182, 91, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273,
+182, 91, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182,
+91, 0, 77, 154, 231, 308, 385, 462, 538, 615, 692, 769, 846, 923, 1000, 944, 889, 833, 778, 722, 667, 611, 556,
+500, 444, 389, 333, 278, 222, 167, 111, 56, 0, 53, 105, 158, 211, 263, 316, 368, 421, 474, 526, 579, 632, 684,
+737, 789, 842, 895, 947, 1000, 950, 900, 850, 800, 750, 700, 650, 600, 550, 500, 450, 400, 350, 300, 250, 200,
+150, 100, 50, 0, 43, 87, 130, 174, 217, 261, 304, 348, 391, 435, 478, 522, 565, 609, 652, 696, 739, 783, 826,
+870, 913, 957, 1000, 957, 913, 870, 826, 783, 739, 696, 652, 609, 565, 522, 478, 435, 391, 348, 304, 261, 217,
+174, 130, 87, 43, 0, 38, 77, 115, 154, 192, 231, 269, 308, 346, 385, 423, 462, 500, 538, 577, 615, 654, 692,
+731, 769, 808, 846, 885, 923, 962, 1000, 964, 929, 893, 857, 821, 786, 750, 714, 679, 643, 607, 571, 536, 500,
+464, 429, 393, 357, 321, 286, 250, 214, 179, 143, 107, 71, 36, 0, 33, 67, 100, 133, 167, 200, 233, 267, 300,
+333, 367, 400, 433, 467, 500, 533, 567, 600, 633, 667, 700, 733, 767, 800, 833, 867, 900, 933, 967, 1000, 970,
+939, 909, 879, 848, 818, 788, 758, 727, 697, 667, 636, 606, 576, 545, 515, 485, 455, 424, 394, 364, 333, 303,
+273, 242, 212, 182, 152, 121, 91, 61, 30, 0, 29, 57, 86, 114, 143, 171, 200, 229, 257, 286, 314, 343, 371, 400,
+429, 457, 486, 514, 543, 571, 600, 629, 657, 686, 714, 743, 771, 800, 829, 857, 886, 914, 943, 971, 1000, 974,
+947, 921, 895, 868, 842, 816, 789, 763, 737, 711, 684, 658, 632, 605, 579, 553, 526, 500, 474, 447, 421, 395,
+368, 342, 316, 289, 263, 237, 211, 184, 158, 132, 105, 79, 53, 26, 0, 24, 49, 73, 98, 122, 146, 171, 195, 220,
+244, 268, 293, 317, 341, 366, 390, 415, 439, 463, 488, 512, 537, 561, 585, 610, 634, 659, 683, 707, 732, 756,
+780, 805, 829, 854, 878, 902, 927, 951, 976, 1000, 977, 955, 932, 909, 886, 864, 841, 818, 795, 773, 750, 727,
+705, 682, 659, 636, 614, 591, 568, 545, 523, 500, 477, 455, 432, 409, 386, 364, 341, 318, 295, 273, 250, 227,
+205, 182, 159, 136, 114, 91, 68, 45, 23, 0
+};
+
+//偶数三角滤波器首尾相连的折线
+const u16 tri_even[] = {
+
+91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 91,
+182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 91, 182,
+273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 91, 182, 273,
+364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 91, 182, 273, 364,
+455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 91, 182, 273, 364, 455,
+545, 636, 727, 818, 909, 1000, 923, 846, 769, 692, 615, 538, 462, 385, 308, 231, 154, 77, 0, 56, 111, 167, 222,
+278, 333, 389, 444, 500, 556, 611, 667, 722, 778, 833, 889, 944, 1000, 947, 895, 842, 789, 737, 684, 632, 579,
+526, 474, 421, 368, 316, 263, 211, 158, 105, 53, 0, 50, 100, 150, 200, 250, 300, 350, 400, 450, 500, 550, 600,
+650, 700, 750, 800, 850, 900, 950, 1000, 957, 913, 870, 826, 783, 739, 696, 652, 609, 565, 522, 478, 435, 391,
+348, 304, 261, 217, 174, 130, 87, 43, 0, 43, 87, 130, 174, 217, 261, 304, 348, 391, 435, 478, 522, 565, 609, 652,
+696, 739, 783, 826, 870, 913, 957, 1000, 962, 923, 885, 846, 808, 769, 731, 692, 654, 615, 577, 538, 500, 462,
+423, 385, 346, 308, 269, 231, 192, 154, 115, 77, 38, 0, 36, 71, 107, 143, 179, 214, 250, 286, 321, 357, 393, 429,
+464, 500, 536, 571, 607, 643, 679, 714, 750, 786, 821, 857, 893, 929, 964, 1000, 967, 933, 900, 867, 833, 800, 767,
+733, 700, 667, 633, 600, 567, 533, 500, 467, 433, 400, 367, 333, 300, 267, 233, 200, 167, 133, 100, 67, 33, 0, 30,
+61, 91, 121, 152, 182, 212, 242, 273, 303, 333, 364, 394, 424, 455, 485, 515, 545, 576, 606, 636, 667, 697, 727,
+758, 788, 818, 848, 879, 909, 939, 970, 1000, 971, 943, 914, 886, 857, 829, 800, 771, 743, 714, 686, 657, 629, 600,
+571, 543, 514, 486, 457, 429, 400, 371, 343, 314, 286, 257, 229, 200, 171, 143, 114, 86, 57, 29, 0, 26, 53, 79,
+105, 132, 158, 184, 211, 237, 263, 289, 316, 342, 368, 395, 421, 447, 474, 500, 526, 553, 579, 605, 632, 658, 684,
+711, 737, 763, 789, 816, 842, 868, 895, 921, 947, 974, 1000, 976, 951, 927, 902, 878, 854, 829, 805, 780, 756, 732,
+707, 683, 659, 634, 610, 585, 561, 537, 512, 488, 463, 439, 415, 390, 366, 341, 317, 293, 268, 244, 220, 195, 171,
+146, 122, 98, 73, 49, 24, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
+0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
+};
+#endif
+
+#if 1  //512 point fft
+//三角滤波器中心频率点
+const u16 tri_cen[] = {
+	4, 7, 12, 16, 21, 26, 32, 38, 44, 51, 59, 67, 76, 85, 96, 107, 119, 132, 146, 161, 177, 195, 213, 234
+};
+
+//奇数三角滤波器首尾相连的折线
+const u16 tri_odd[] = {
+
+0, 0, 0, 0, 333, 667, 1000, 800, 600, 400, 200, 0, 250, 500, 750, 1000, 800, 600, 400, 200, 0, 200, 400, 600, 800, 1000, 833, 667, 500, 333,
+167, 0, 167, 333, 500, 667, 833, 1000, 833, 667, 500, 333, 167, 0, 143, 286, 429, 571, 714, 857, 1000, 875, 750, 625, 500, 375, 250, 125, 0,
+125, 250, 375, 500, 625, 750, 875, 1000, 889, 778, 667, 556, 444, 333, 222, 111, 0, 111, 222, 333, 444, 556, 667, 778, 889, 1000, 909, 818,
+727, 636, 545, 455, 364, 273, 182, 91, 0, 91, 182, 273, 364, 455, 545, 636, 727, 818, 909, 1000, 917, 833, 750, 667, 583, 500, 417, 333, 250,
+167, 83, 0, 77, 154, 231, 308, 385, 462, 538, 615, 692, 769, 846, 923, 1000, 929, 857, 786, 714, 643, 571, 500, 429, 357, 286, 214, 143, 71, 0,
+67, 133, 200, 267, 333, 400, 467, 533, 600, 667, 733, 800, 867, 933, 1000, 938, 875, 813, 750, 688, 625, 563, 500, 438, 375, 313, 250, 188,
+125, 63, 0, 56, 111, 167, 222, 278, 333, 389, 444, 500, 556, 611, 667, 722, 778, 833, 889, 944, 1000, 944, 889, 833, 778, 722, 667, 611, 556,
+500, 444, 389, 333, 278, 222, 167, 111, 56, 0, 48, 95, 143, 190, 238, 286, 333, 381, 429, 476, 524, 571, 619, 667, 714, 762, 810, 857, 905, 952,
+1000, 955, 909, 864, 818, 773, 727, 682, 636, 591, 545, 500, 455, 409, 364, 318, 273, 227, 182, 136, 91, 45, 0
+};
+
+//偶数三角滤波器首尾相连的折线
+const u16 tri_even[] = {
+
+250, 500, 750, 1000, 667, 334, 0, 200, 400, 600, 800, 1000, 750, 500, 250, 0, 200, 400, 600, 800, 1000, 800, 600, 400, 200, 0, 167, 333, 500,
+667, 833, 1000, 833, 667, 500, 333, 167, 0, 167, 333, 500, 667, 833, 1000, 857, 714, 571, 429, 286, 143, 0, 125, 250, 375, 500, 625, 750, 875,
+1000, 875, 750, 625, 500, 375, 250, 125, 0, 111, 222, 333, 444, 556, 667, 778, 889, 1000, 889, 778, 667, 556, 444, 333, 222, 111, 0, 91, 182,
+273, 364, 455, 545, 636, 727, 818, 909, 1000, 909, 818, 727, 636, 545, 455, 364, 273, 182, 91, 0, 83, 167, 250, 333, 417, 500, 583, 667, 750,
+833, 917, 1000, 923, 846, 769, 692, 615, 538, 462, 385, 308, 231, 154, 77, 0, 71, 143, 214, 286, 357, 429, 500, 571, 643, 714, 786, 857, 929,
+1000, 933, 867, 800, 733, 667, 600, 533, 467, 400, 333, 267, 200, 133, 67, 0, 63, 125, 188, 250, 313, 375, 438, 500, 563, 625, 688, 750, 813,
+875, 938, 1000, 944, 889, 833, 778, 722, 667, 611, 556, 500, 444, 389, 333, 278, 222, 167, 111, 56, 0, 56, 111, 167, 222, 278, 333, 389, 444,
+500, 556, 611, 667, 722, 778, 833, 889, 944, 1000, 952, 905, 857, 810, 762, 714, 667, 619, 571, 524, 476, 429, 381, 333, 286, 238, 190, 143,
+95, 48, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
+};
+#endif
+
+// 反离散余弦变换 余弦表 24*12
+const s8 dct_arg[] = {
+
+	100, 98, 95, 90, 83, 75, 66, 56, 44, 32, 20, 7, -7, -20, -32, -44, -56, -66, -75, -83, -90, -95, -98, -100,
+	99, 92, 79, 61, 38, 13, -13, -38, -61, -79, -92, -99, -99, -92, -79, -61, -38, -13, 13, 38, 61, 79, 92, 99,
+	98, 83, 56, 20, -20, -56, -83, -98, -98, -83, -56, -20, 20, 56, 83, 98, 98, 83, 56, 20, -20, -56, -83, -98,
+	97, 71, 26, -26, -71, -97, -97, -71, -26, 26, 71, 97, 97, 71, 26, -26, -71, -97, -97, -71, -26, 26, 71, 97,
+	95, 56, -7, -66, -98, -90, -44, 20, 75, 100, 83, 32, -32, -83, -100, -75, -20, 44, 90, 98, 66, 7, -56, -95,
+	92, 38, -38, -92, -92, -38, 38, 92, 92, 38, -38, -92, -92, -38, 38, 92, 92, 38, -38, -92, -92, -38, 38, 92,
+	90, 20, -66, -100, -56, 32, 95, 83, 7, -75, -98, -44, 44, 98, 75, -7, -83, -95, -32, 56, 100, 66, -20, -90,
+	87, 0, -87, -87, 0, 87, 87, 0, -87, -87, 0, 87, 87, 0, -87, -87, 0, 87, 87, 0, -87, -87, 0, 87,
+	83, -20, -98, -56, 56, 98, 20, -83, -83, 20, 98, 56, -56, -98, -20, 83, 83, -20, -98, -56, 56, 98, 20, -83,
+	79, -38, -99, -13, 92, 61, -61, -92, 13, 99, 38, -79, -79, 38, 99, 13, -92, -61, 61, 92, -13, -99, -38, 79,
+	75, -56, -90, 32, 98, -7, -100, -20, 95, 44, -83, -66, 66, 83, -44, -95, 20, 100, 7, -98, -32, 90, 56, -75,
+	71, -71, -71, 71, 71, -71, -71, 71, 71, -71, -71, 71, 71, -71, -71, 71, 71, -71, -71, 71, 71, -71, -71, 71,
+};
+
+#endif
+

libraries/Maix_Speech_Recognition/src/util/VAD.c

@@ -0,0 +1,333 @@
+/********     VAD.C       *******/
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include "g_def.h"
+#include "ADC.h"
+#include "VAD.h"
+
+#define n_thl_ratio	1		//噪声门限系数 n_thl=n_max_mean*n_thl_ratio
+#define s_thl_ratio(x)	(x*30/10)	//短时幅度判决门限系数 s_thl=sum_mean*s_thl_ratio
+#define z_thl_ratio(x)	(x*2/160)	//短时过零率 判决门限系数 常数
+
+
+#define atap_frm_t		30						//背景噪音自适应时间帧长度 ms
+#define atap_frm_len	((fs/1000)*atap_frm_t)	//背景噪音自适应帧长度
+
+u16 vad_data[VcBuf_Len];
+u32 frm_n;
+
+/*	求取自适应参数
+ *	noise	：噪声起始点
+	n_len	：噪声长度
+	atap	；自适应参数
+*/
+void noise_atap(const u16 *noise, u16 n_len, atap_tag *atap)
+{
+	u32 h, i;
+	u32	n_max;
+	u32 max_sum;//每一帧噪声最大值 累加取平均 求噪声阈值
+	u32	n_sum;	//所有数值之和 求平均值 确定零(中)值
+	u32 mid;	//中值
+	u32 abs;	//绝对值
+	u32 abs_sum;//绝对值和
+	u32 frm_num;
+
+	if ((n_len%atap_frm_len) != 0)	//参数检查
+		return;
+	frm_num = n_len/atap_frm_len;
+
+	n_sum = 0;
+	max_sum = 0;
+	for (i = 0; i < n_len; i++)
+		n_sum +=  *(noise+i);
+	mid = n_sum/i;
+
+	abs_sum = 0;
+	for (i = 0; i < n_len; i += atap_frm_len) {
+		n_max = 0;
+		for (h = 0; h < atap_frm_len; h++) {
+			abs = (*(noise+i+h) > mid)?(*(noise+i+h)-mid):(mid-*(noise+i+h));
+			if (abs > n_max)	////取每帧最大绝对值
+				n_max = abs;
+			abs_sum += abs;
+		}
+		max_sum += n_max;
+		//USART1_printf("n_max=%d ", n_max);
+		//USART1_printf("max_sum=%d\r\n", max_sum);
+	}
+
+	abs_sum /= (n_len/FRAME_LEN);
+	max_sum /= frm_num;
+	atap->mid_val = mid;
+	atap->n_thl = max_sum*n_thl_ratio;
+	atap->s_thl = s_thl_ratio(abs_sum);
+	atap->z_thl = z_thl_ratio(FRAME_LEN)/n_thl_ratio;
+	printf("VAD sum=%d ", atap->s_thl);
+	printf("VAD zero=%d\n", atap->z_thl);
+}
+#define	v_durmin_t	200	//有效语音最短时间门限 ms
+#define	v_durmin_f	v_durmin_t/(frame_time-frame_mov_t)	//有效语音最短帧数
+#define	s_durmax_t	210	//无声段最长时间门限 ms
+#define	s_durmax_f	s_durmax_t/(frame_time-frame_mov_t)//无声段最长帧数
+
+/*******
+ *	VAD	(Voice activity detection) 语音活动检测
+	检测出一段声音中的有效语音 起始点和长度 最多3段语音
+
+	短时幅度 短时过零率求取：
+	短时幅度直接累加
+	短时过零率改进为过门限率，设置正负两个绝对值相等的门限。
+	构成门限带，穿过门限带计作过零
+
+	端点判决：
+	1.判断语音起始点，要求能够滤除突发性噪声
+	突发性噪声可以引起短时能量或过零率的数值很高，但是往往不能维持足够长的时间，
+	如门窗的开关，物体的碰撞等引起的噪声，这些都可以通过设定最短时间门限来判别。
+	超过两门限之一或全部，并且持续时间超过有效语音最短时间门限，
+	返回最开始超过门限的时间点，将其标记为有效语音起始点。
+
+	2.判断语音结束点，要求不能丢弃连词中间短暂的有可能被噪声淹没的“寂静段”
+	同时低于两门限，并且持续时间超过无声最长时间门限，
+	返回最开始低于门限的时间点，将其标记为有效语音结束点。
+*********/
+void VAD(const u16 *vc, u16 buf_len, valid_tag *valid_voice, atap_tag *atap_arg)
+{
+	u8	last_sig = 0;	// 上次跃出门限带的状态 1:门限带以下；2:门限带以上
+	u8	cur_stus = 0;	// 当前语音段状态 0无声段  1前端过渡段  2语音段  3后端过渡段
+	u16 front_duration = 0;//前端过渡段超过门限值持续帧数
+	u16 back_duration = 0;//后端过渡段低于门限值持续帧数
+	u32 h, i;
+	u32 frm_sum;	// 短时绝对值和
+	u32 frm_zero;	// 短时过零(门限)率
+	u32 a_thl;	// 上门限值
+	u32 b_thl;	// 下门限值
+
+	u8	valid_con = 0;//语音段计数 最大max_vc_con
+	u32 frm_con = 0;	//帧计数
+
+	a_thl = atap_arg->mid_val+atap_arg->n_thl;
+	b_thl = atap_arg->mid_val-atap_arg->n_thl;
+
+	for (i = 0; i < max_vc_con; i++) {
+		((valid_tag *)(valid_voice+i))->start = (void *)0;
+		((valid_tag *)(valid_voice+i))->end = (void *)0;
+	}
+
+	for (i = 0; i < (buf_len-FRAME_LEN); i += (FRAME_LEN-frame_mov)) {
+		frm_con++;
+
+		frm_sum = 0;
+		for (h = 0; h < FRAME_LEN; h++)//短时绝对值和
+			frm_sum += (*(vc+i+h) > (atap_arg->mid_val))?(*(vc+i+h)-(atap_arg->mid_val)):((atap_arg->mid_val)-*(vc+i+h));
+
+		frm_zero = 0;
+		for (h = 0; h < (FRAME_LEN-1); h++) {//短时过门限率
+			if (*(vc+i+h) >= a_thl)			//大于上门限值
+				last_sig = 2;
+			else if (*(vc+i+h) < b_thl)	//小于下门限值
+				last_sig = 1;
+
+			if (*(vc+i+h+1) >= a_thl) {
+				if (last_sig == 1)
+					frm_zero++;
+			} else if (*(vc+i+h+1) < b_thl) {
+				if (last_sig == 2)
+					frm_zero++;
+			}
+		}
+		//USART1_printf("frm_con=%d ",frm_con);
+		//USART1_printf("frm_sum=%d ",frm_sum);
+		//USART1_printf("frm_zero=%d\r\n",frm_zero);
+
+		if ((frm_sum > (atap_arg->s_thl)) || (frm_zero > (atap_arg->z_thl))) {
+		//至少有一个参数超过其门限值
+		//	if(frm_sum>(atap_arg->s_thl))
+		//		printf("frm_sum ok\n");
+		//	else
+		//		printf("frm_zero ok\n");
+			if (cur_stus == 0) {//如果当前是无声段
+				cur_stus = 1; //进入前端过渡段
+				front_duration = 1; //前端过渡段持续帧数置1 第一帧
+			} else if (cur_stus == 1) {//当前是前端过渡段
+				front_duration++;
+				if (front_duration >= v_durmin_f) { //前端过渡段帧数超过最短有效语音帧数
+					cur_stus = 2; //进入语音段
+					((valid_tag *)(valid_voice+valid_con))->start = (u16 *)vc+i-((v_durmin_f-1)*(FRAME_LEN-frame_mov));//记录起始帧位置
+					front_duration = 0; //前端过渡段持续帧数置0
+				}
+			} else if (cur_stus == 3) { //如果当前是后端过渡段 两参数都回升到门限值以上
+				back_duration = 0;
+				cur_stus = 2; //记为语音段
+			}
+		} else {//两参数都在门限值以下
+		//	printf("frm not ok\n");
+			if (cur_stus == 2) {//当前是语音段
+				cur_stus = 3;//设为后端过渡段
+				back_duration = 1; //前端过渡段持续帧数置1 第一帧
+			} else if (cur_stus == 3) {//当前是后端过渡段
+				back_duration++;
+				if (back_duration >= s_durmax_f) { //后端过渡段帧数超过最长无声帧数
+					cur_stus = 0; //进入无声段
+					((valid_tag *)(valid_voice+valid_con))->end = (u16 *)vc+i-(s_durmax_f*(FRAME_LEN-frame_mov))+FRAME_LEN;//记录结束帧位置
+					valid_con++;
+					if (valid_con == max_vc_con)
+						return;
+					back_duration = 0;
+				}
+			} else if (cur_stus == 1) {//当前是前端过渡段 两参数都回落到门限值以下
+								//持续时间低于语音最短时间门限 视为短时噪声
+				front_duration = 0;
+				cur_stus = 0; //记为无声段
+			}
+		}
+	}
+}
+
+u8 VAD2(const u16 *vc, valid_tag *valid_voice, atap_tag *atap_arg)
+{
+	u8	last_sig = 0;	// 上次跃出门限带的状态 1:门限带以下；2:门限带以上
+	static u8	cur_stus;	// 当前语音段状态 0无声段  1前端过渡段  2语音段  3后端过渡段
+	static u16 front_duration;//前端过渡段超过门限值持续帧数
+	static u16 back_duration;//后端过渡段低于门限值持续帧数
+	static u8 word_num_tmp;
+	u32 h, i;
+	u32 frm_sum;	// 短时绝对值和
+	u32 frm_zero;	// 短时过零(门限)率
+	u32 a_thl;	// 上门限值
+	u32 b_thl;	// 下门限值
+
+	a_thl = atap_arg->mid_val+atap_arg->n_thl;
+	b_thl = atap_arg->mid_val-atap_arg->n_thl;
+
+	frm_sum = 0;
+	for (h = 0; h < FRAME_LEN; h++)//短时绝对值和
+		frm_sum += (*(vc+h) > (atap_arg->mid_val))?(*(vc+h)-(atap_arg->mid_val)):((atap_arg->mid_val)-*(vc+h));
+
+	frm_zero = 0;
+	for (h = 0; h < (FRAME_LEN-1); h++) {//短时过门限率
+		if (*(vc+h) >= a_thl)			//大于上门限值
+			last_sig = 2;
+		else if (*(vc+h) < b_thl)	//小于下门限值
+			last_sig = 1;
+
+		if (*(vc+h+1) >= a_thl) {
+			if (last_sig == 1)
+				frm_zero++;
+		} else if (*(vc+h+1) < b_thl) {
+			if (last_sig == 2)
+				frm_zero++;
+		}
+	}
+
+//	printf("frm_sum=%d\n",frm_sum);
+//	printf("frm_zero=%d ",frm_zero);
+
+	if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len - (FRAME_LEN - frame_mov)) {//over frame length
+		cur_stus = 0; //进入无声段
+		frm_n = 0;
+		printf("I am here\n");
+		return 0;
+	}
+	if ((frm_sum > (atap_arg->s_thl)) || (frm_zero > (atap_arg->z_thl))) {
+	//至少有一个参数超过其门限值
+		if (frm_sum > (atap_arg->s_thl))
+			printf("frm_sum ok\n");
+		else
+			printf("frm_zero ok\n");
+		if (cur_stus == 0) {//如果当前是无声段
+			cur_stus = 1; //进入前端过渡段
+			front_duration = 1; //前端过渡段持续帧数置1 第一帧
+			frm_n = 0;
+			word_num_tmp = 1;
+			for (i = 0; i < FRAME_LEN; i++) //copy the valid data
+				vad_data[i] = vc[i];
+		} else if (cur_stus == 1) { //当前是前端过渡段
+			front_duration++;
+			if (front_duration >= v_durmin_f) {//前端过渡段帧数超过最短有效语音帧数
+				cur_stus = 2; //进入语音段
+				front_duration = 0; //前端过渡段持续帧数置0
+				valid_voice[0].start = (u16 *)vad_data;
+			}
+			for (i = 0; i < FRAME_LEN - frame_mov; i++)//copy the valid data
+				vad_data[FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n + i] = vc[i + frame_mov];
+			frm_n++;
+			if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len + frame_mov - FRAME_LEN) {
+				cur_stus = 0; //进入无声段
+				valid_voice[0].end = (u16 *)vad_data + VcBuf_Len;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+		} else if (cur_stus == 3) { //如果当前是后端过渡段 两参数都回升到门限值以上
+			if (back_duration > 5)
+				word_num_tmp++;
+		//	printf("back_duration = %d\n", back_duration);
+			back_duration = 0;
+			cur_stus = 2; //记为语音段
+			for (i = 0; i < FRAME_LEN - frame_mov; i++)//copy the valid data
+				vad_data[FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n + i] = vc[i + frame_mov];
+			frm_n++;
+			if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len + frame_mov - FRAME_LEN) {
+				cur_stus = 0; //进入无声段
+				valid_voice[0].end = (u16 *)vad_data + VcBuf_Len;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+		} else if (cur_stus == 2) {
+			for (i = 0; i < FRAME_LEN - frame_mov; i++)//copy the valid data
+				vad_data[FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n + i] = vc[i + frame_mov];
+			frm_n++;
+			if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len + frame_mov - FRAME_LEN) {
+				cur_stus = 0; //进入无声段
+				valid_voice[0].end = (u16 *)vad_data + VcBuf_Len;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+
+		}
+	} else {//两参数都在门限值以下
+//		printf("frm error\n");
+		if (cur_stus == 2) {//当前是语音段
+			cur_stus = 3;//设为后端过渡段
+			back_duration = 1; //前端过渡段持续帧数置1 第一帧
+			#if 0
+			for (i = 0; i < FRAME_LEN - frame_mov; i++)//copy the valid data
+				vad_data[FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n + i] = vc[i + frame_mov];
+			frm_n++;
+			if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len + frame_mov - FRAME_LEN) {
+				cur_stus = 0; //进入无声段
+				valid_voice[0].end = (u16 *)vad_data + VcBuf_Len;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+			#endif
+		} else if (cur_stus == 3) {//当前是后端过渡段
+			back_duration++;
+			#if 0
+			for (i = 0; i < FRAME_LEN - frame_mov; i++)//copy the valid data
+				vad_data[FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n + i] = vc[i + frame_mov];
+			frm_n++;
+			if (FRAME_LEN + (FRAME_LEN-frame_mov) * frm_n > VcBuf_Len + frame_mov - FRAME_LEN) {
+				cur_stus = 0; //进入无声段
+				valid_voice[0].end = (u16 *)vad_data + VcBuf_Len;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+#endif
+			if (back_duration >= s_durmax_f) {//后端过渡段帧数超过最长无声帧数
+				cur_stus = 0; //进入无声段
+				back_duration = 0;
+				frm_n = frm_n - s_durmax_f;
+				valid_voice[0].end = (u16 *)vad_data+frm_n*(FRAME_LEN-frame_mov)+FRAME_LEN;//记录结束帧位置
+//				valid_voice[0].word_num = word_num_tmp;
+				return 1;
+			}
+		} else if (cur_stus == 1) {//当前是前端过渡段 两参数都回落到门限值以下
+							//持续时间低于语音最短时间门限 视为短时噪声
+			front_duration = 0;
+			cur_stus = 0; //记为无声段
+			frm_n = 0;
+		}
+	}
+	return 0;
+}

libraries/Maix_Speech_Recognition/src/util/VAD.h

@@ -0,0 +1,42 @@
+#ifndef _VAD_H
+#define _VAD_H
+
+#include "g_def.h"
+
+#define	max_vc_con	3	//VAD最多检测的语音段数
+#define frame_time	20						// 每帧时间长度 单位ms
+#define frame_mov_t	10						// 帧移
+#define FRAME_LEN	(frame_time*fs/1000)	// 帧长
+#define frame_mov	(frame_mov_t *fs/1000)	// 帧移，相邻帧交叠部分
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+#pragma pack(1)
+typedef struct {
+	u32 mid_val;	//语音段中值 相当于有符号的0值 用于短时过零率计算
+	u16	n_thl;		//噪声阈值，用于短时过零率计算
+	u16 z_thl;		//短时过零率阈值，超过此阈值，视为进入过渡段。
+	u32 s_thl;		//短时累加和阈值，超过此阈值，视为进入过渡段。
+} atap_tag;			//自适应参数
+#pragma pack()
+
+//#pragma pack(4)
+typedef struct {
+	u16 *start;	//起始点
+	u16 *end;	//结束点
+//	u8 word_num;
+} valid_tag;	//有效语音段
+//#pragma pack()
+
+void noise_atap(const u16 *noise, u16 n_len, atap_tag *atap);
+void VAD(const u16 *vc, u16 buf_len, valid_tag *valid_voice, atap_tag *atap_arg);
+u8 VAD2(const u16 *vc, valid_tag *valid_voice, atap_tag *atap_arg);
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif

libraries/Maix_Speech_Recognition/src/util/flash.c

@@ -0,0 +1,105 @@
+/*	适用于STM32F103VE
+ *	全部falsh 512KB 256页 每页2KB
+
+	每个语音特征模板占用4KB 采用冗余模板 每个语音指令4个特征模板
+	初步设计设定20个语音指令 共占用320KB
+
+	flash最后320KB用于存储语音特征模板
+	编译器需设置 以免存储区被代码占用
+	烧写程序时也不能擦除存储区 选擦除需要的页
+*/
+#include <stdint.h>
+#include <stdlib.h>
+#include <stdio.h>
+#include <string.h>
+#include "g_def.h"
+#include "flash.h"
+#include "uarths.h"
+#include "MFCC.h"
+//#include "voice_modle.h"
+
+v_ftr_tag ftr_save[20 * 4];
+
+u8 save_ftr_mdl(v_ftr_tag *ftr, u32 addr)
+{
+//	u32 ftr_size;
+
+	addr = addr / size_per_ftr;
+
+	if (addr > 40) {
+		printf("flash addr error");
+		return Flash_Fail;
+	}
+	ftr->save_sign = save_mask;
+	ftr_save[addr] = *ftr;
+
+//	ftr_size=2*mfcc_num*ftr->frm_num;
+
+	return Flash_Success;
+}
+#if 0
+void init_voice_mdl(void)
+{
+	uint16_t i, j, comm;
+
+	for (comm = 0; comm < 4; comm++) {
+		for (j = 0; j < 4; j++) {
+			ftr_save[comm*4+j].save_sign = save_mask;
+			ftr_save[comm*4+j].frm_num = mdl_fram_num[comm*4+j];
+//			ftr_save[comm*4+j].word_num = 2;
+		}
+	}
+//
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[0].mfcc_dat[i] = start1[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[1].mfcc_dat[i] = start2[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[2].mfcc_dat[i] = start3[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[3].mfcc_dat[i] = start4[i];
+
+
+//
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[4].mfcc_dat[i] = pause1[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[5].mfcc_dat[i] = pause2[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[6].mfcc_dat[i] = pause3[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[7].mfcc_dat[i] = pause4[i];
+
+//
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[8].mfcc_dat[i] = cancle1[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[9].mfcc_dat[i] = cancle2[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[10].mfcc_dat[i] = cancle3[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[11].mfcc_dat[i] = cancle4[i];
+
+//
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[12].mfcc_dat[i] = confirm1[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[13].mfcc_dat[i] = confirm2[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[14].mfcc_dat[i] = confirm3[i];
+
+	for (i = 0; i < (vv_frm_max * mfcc_num); i++)
+		ftr_save[15].mfcc_dat[i] = confirm4[i];
+}
+#endif

libraries/Maix_Speech_Recognition/src/util/flash.h

@@ -0,0 +1,39 @@
+#ifndef __FLASH_H
+#define __FLASH_H
+
+#include "g_def.h"
+#include "MFCC.h"
+
+#define FLASH_PAGE_SIZE			2048
+
+#define Flash_Fail		3
+#define Flash_Success	0
+
+#define save_mask		12345
+
+#define size_per_ftr	(4*1024)
+#define page_per_ftr	(size_per_ftr/FLASH_PAGE_SIZE)
+#define ftr_per_comm	4
+#define size_per_comm	(ftr_per_comm*size_per_ftr)
+#define comm_num		10
+#define ftr_total_size	(size_per_comm*comm_num)
+//#define ftr_end_addr	0x8080000
+#define ftr_end_addr (size_per_ftr * ftr_per_comm * comm_num)
+#define ftr_start_addr	0 //(ftr_end_addr-ftr_total_size)
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+
+u8 save_ftr_mdl(v_ftr_tag *ftr, u32 addr);
+
+//void init_voice_mdl(void);
+extern v_ftr_tag ftr_save[20 * 4];
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif
+

libraries/Maix_Speech_Recognition/src/util/g_def.h

@@ -0,0 +1,13 @@
+#ifndef _G_DEF_H_
+#define _G_DEF_H_
+
+typedef uint32_t  u32;
+typedef uint16_t u16;
+typedef uint8_t  u8;
+
+typedef int32_t  s32;
+typedef int16_t s16;
+typedef int8_t  s8;
+
+#endif
+

libraries/NS2009/examples/drawline/drawline.ino

@@ -20,7 +20,7 @@ void setup()
     pinMode(key, INPUT);  
     lcd.begin(15000000, COLOR_RED);    
     touchscreen.begin();
-    touchscreen.calibrate(320,240);
+    touchscreen.calibrate(320, 240);
 }
 
 void loop()
@@ -29,20 +29,16 @@ void loop()
     touchscreen_status = touchscreen.getStatus();
     touchscreen_x = touchscreen.getX();
     touchscreen_y = touchscreen.getY();
-    if(draw){
+    if (draw) {
         lcd.writeLine(x_last,y_last,touchscreen_x,touchscreen_y,COLOR_WHITE);
     }
-    if(status_last!=touchscreen_status){
-        if (touchscreen_status == TOUCH_BEGIN || touchscreen_status == TOUCH_MOVE)
-            draw = true;
-        else
-            draw = false;
-        status_last=touchscreen_status;
+    if (status_last != touchscreen_status) {
+        draw = (touchscreen_status == TOUCH_BEGIN || touchscreen_status == TOUCH_MOVE);
+        status_last = touchscreen_status;
     }
     x_last = touchscreen_x;
     y_last = touchscreen_y;
-    if(digitalRead(key) == LOW)
-    {
+    if (digitalRead(key) == LOW) {
         lcd.fillScreen(COLOR_BLACK);
     }
 }

libraries/SD/library.properties

@@ -1,4 +1,4 @@
-name=SD(k210)
+name=SD
 version=1.2.4
 author=Arduino, SparkFun, Neucrack
 maintainer=Sipeed <support@sipeed.com>

libraries/SD/src/utility/Sd2Card.cpp

@@ -20,6 +20,9 @@
 #define USE_SPI_LIB
 #include <Arduino.h>
 #include "Sd2Card.h"
+#include "fpioa.h"
+#include "gpio.h"
+#include "wiring_digital.h"
 //------------------------------------------------------------------------------
 #ifndef SOFTWARE_SPI
 #ifdef USE_SPI_LIB
@@ -251,6 +254,7 @@ uint8_t Sd2Card::init(uint8_t sckRateID, uint8_t chipSelectPin) {
   // set pin modes
   pinMode(chipSelectPin_, OUTPUT);
   digitalWrite(chipSelectPin_, HIGH);
+
 #ifndef USE_SPI_LIB
   pinMode(SPI_MISO_PIN, INPUT);
   pinMode(SPI_MOSI_PIN, OUTPUT);

libraries/Sipeed_GC0328/examples/sipeed_gc0328.ino

@@ -0,0 +1,26 @@
+#include <Sipeed_GC0328.h>
+#include <Sipeed_ST7789.h>
+
+SPIClass spi_(SPI0); // MUST be SPI0 for Maix series on board LCD
+Sipeed_ST7789 lcd(320, 240, spi_);
+Sipeed_GC0328 camera(FRAMESIZE_QVGA, PIXFORMAT_RGB565, &Wire);
+
+void setup()
+{
+  Serial.begin(115200);
+  lcd.begin(15000000, COLOR_RED);
+  if(!camera.begin())
+    Serial.printf("camera init fail\n");
+  else
+    Serial.printf("camera init success\n");
+  camera.run(true);
+}
+
+void loop()
+{
+  uint8_t*img = camera.snapshot();
+  if(img == nullptr || img==0)
+    Serial.printf("snap fail\r\n");
+  else
+    lcd.drawImage(0, 0, camera.width(), camera.height(), (uint16_t*)img);
+}

libraries/Sipeed_GC0328/examples/sipeed_gc0328_binocular.ino

@@ -0,0 +1,35 @@
+#include <Sipeed_GC0328.h>
+#include <Sipeed_ST7789.h>
+
+SPIClass spi_(SPI0); // MUST be SPI0 for Maix series on board LCD
+Sipeed_ST7789 lcd(320, 240, spi_);
+Sipeed_GC0328 camera(FRAMESIZE_QVGA, PIXFORMAT_RGB565, &Wire);
+
+// Use left camera if true, right camera when true
+bool leftCamera = true;
+
+void setup()
+{
+  Serial.begin(115200);
+  lcd.begin(15000000, COLOR_RED);
+  
+  // Start camera in binocular mode
+  if(!camera.begin(true))
+    Serial.printf("camera init fail\n");
+  else
+    Serial.printf("camera init success\n");
+  camera.run(true);
+}
+
+void loop()
+{
+  // Switch left/right cameras
+  camera.shutdown(leftCamera);
+  leftCamera = !leftCamera;
+  
+  uint8_t*img = camera.snapshot();
+  if(img == nullptr || img==0)
+    Serial.printf("snap fail\r\n");
+  else
+    lcd.drawImage(0, 0, camera.width(), camera.height(), (uint16_t*)img);
+}

libraries/Sipeed_GC0328/keywords.txt

@@ -0,0 +1,29 @@
+#######################################
+# Syntax Coloring Map 
+#######################################
+
+#######################################
+# Datatypes (KEYWORD1)
+#######################################
+
+
+#######################################
+# Methods and Functions (KEYWORD2)
+#######################################
+begin                KEYWORD2
+end                  KEYWORD2
+reset                KEYWORD2
+setPixFormat         KEYWORD2
+setFrameSize         KEYWORD2
+run                  KEYWORD2
+id                   KEYWORD2
+snapshot             KEYWORD2
+setRotation          KEYWORD2
+setInvert            KEYWORD2
+
+#######################################
+# Constants (LITERAL1)
+#######################################
+
+
+

libraries/Sipeed_GC0328/library.properties

@@ -0,0 +1,9 @@
+name=Sipeed_GC0328
+version=1.0
+author=vamoosebbf
+maintainer=vamoosebbf<vamoosebbf@Sipeed.com>
+sentence=Camera Sipeed_GC0328 driver
+paragraph=Camera Sipeed_GC0328 driver
+category=Sensors
+url=
+architectures=k210

libraries/Sipeed_GC0328/src/Sipeed_GC0328.h

@@ -0,0 +1,107 @@
+#ifndef __SIPEED_GC0328_H
+#define __SIPEED_GC0328_H
+
+#include "Camera.h"
+#include "Wire.h"
+
+#define GC0328_ID       (0x9d)
+#define GC0328_ADDR     (0x21)
+
+typedef enum {
+    GAINCEILING_2X,
+    GAINCEILING_4X,
+    GAINCEILING_8X,
+    GAINCEILING_16X,
+    GAINCEILING_32X,
+    GAINCEILING_64X,
+    GAINCEILING_128X,
+} gainceiling_t;
+
+typedef enum {
+    FRAMERATE_2FPS =0x9F,
+    FRAMERATE_8FPS =0x87,
+    FRAMERATE_15FPS=0x83,
+    FRAMERATE_30FPS=0x81,
+    FRAMERATE_60FPS=0x80,
+} framerate_t;
+
+
+class Sipeed_GC0328 : public Camera{
+
+public:
+    Sipeed_GC0328(framesize_t frameSize = FRAMESIZE_QVGA, pixformat_t pixFormat = PIXFORMAT_RGB565, TwoWire *i2c = &Wire);
+    Sipeed_GC0328(uint16_t width, uint16_t height, pixformat_t pixFormat = PIXFORMAT_RGB565, TwoWire *i2c = &Wire);
+    ~Sipeed_GC0328();
+    
+    virtual bool begin();
+    bool begin(bool binocular);
+    virtual void end();
+    bool reset(bool binocular = false);
+    void debug(bool enable);
+    bool setPixFormat(pixformat_t pixFormat);
+    bool setFrameSize(framesize_t frameSize);
+    virtual bool run(bool run);
+    virtual int id();
+    /**
+     * @return pixels 
+     *         If pixels format is RGB565: return RGB565 pixels with every uint16_t one pixel, e.g. RED: 0xF800
+     */
+    virtual uint8_t* snapshot();
+    virtual uint16_t* getRGB565(){ return (uint16_t*)_dataBuffer; };
+    virtual uint8_t* getRGB888(){ return _aiBuffer; };
+    virtual void setRotation(uint8_t rotation);
+    virtual void setInvert(bool invert);
+    virtual void shutdown(bool enable);
+    void setFlip(bool flip);
+
+private:
+    uint8_t* _dataBuffer;    // put RGB565 data
+    uint8_t* _aiBuffer;      // put RGB888 data
+    uint8_t  _resetPolarity; // reset polarity flag
+    uint8_t  _pwdnPolarity;  // PWDN polarity flag
+    uint8_t  _slaveAddr;     // camera address
+    uint8_t  _id;
+    uint32_t _freq;
+    TwoWire *_i2c; // replace sccb
+    bool _vflip;
+    bool _hmirror;
+    bool _debug;
+
+    int dvpInit(uint32_t freq = 14000000);
+    int dvpInitIrq();
+
+    int cambus_scan();
+    int cambus_read_id(uint8_t addr,uint16_t *manuf_id, uint16_t *device_id);
+    int cambus_scan_gc0328(void);
+    int cambus_readb(uint8_t slv_addr, uint8_t reg_addr, uint8_t *reg_data);
+    int cambus_writeb(uint8_t slv_addr, uint8_t reg_addr, uint8_t reg_data);
+
+    int sensor_gc_detect();
+
+    int gc0328_reset();
+    int gc0328_read_reg(uint8_t reg_addr);
+    int gc0328_write_reg(uint8_t reg_addr, uint8_t reg_data);
+
+    int gc0328_set_pixformat(pixformat_t pixformat);
+    int gc0328_set_framesize(framesize_t framesize);
+    int gc0328_set_framerate(framerate_t framerate);
+    int gc0328_set_contrast(int level);
+    int gc0328_set_brightness(int level);
+    int gc0328_set_saturation(int level);
+    int gc0328_set_gainceiling( gainceiling_t gainceiling);
+    int gc0328_set_quality(int qs);
+    int gc0328_set_colorbar(int enable);
+    int gc0328_set_auto_gain(int enable, float gain_db, float gain_db_ceiling);
+    int gc0328_get_gain_db(float *gain_db);
+    int gc0328_set_auto_exposure(int enable, int exposure_us);
+    int gc0328_get_exposure_us(int *exposure_us);
+    int gc0328_set_auto_whitebal(int enable, float r_gain_db, float g_gain_db, float b_gain_db);
+    int gc0328_get_rgb_gain_db(float *r_gain_db, float *g_gain_db, float *b_gain_db);
+    int gc0328_set_hmirror(int enable);
+    int gc0328_set_vflip(int enable);
+    int sensor_snapshot( );
+    int reverse_u32pixel(uint32_t* addr,uint32_t length);
+
+};
+
+#endif

libraries/Sipeed_OV2640/examples/selfie/selfie.ino

@@ -1,6 +1,5 @@
 #include <Sipeed_OV2640.h>
 #include <Sipeed_ST7789.h>
-#include <stdio.h>
 
 SPIClass spi_(SPI0); // MUST be SPI0 for Maix series on board LCD
 Sipeed_ST7789 lcd(320, 240, spi_);
@@ -10,11 +9,12 @@ Sipeed_OV2640 camera(FRAMESIZE_QVGA, PIXFORMAT_RGB565);
 
 void setup()
 {
+    Serial.begin(115200);
     lcd.begin(15000000, COLOR_RED);
     if(!camera.begin())
-      printf("camera init fail\n");
+      Serial.printf("camera init fail\n");
     else
-      printf("camera init success\n");
+      Serial.printf("camera init success\n");
     camera.run(true);
 }
 
@@ -22,7 +22,7 @@ void loop()
 {
   uint8_t*img = camera.snapshot();
   if(img == nullptr || img==0)
-    printf("snap fail\n");
+    Serial.printf("snap fail\n");
   else
     lcd.drawImage(0, 0, camera.width(), camera.height(), (uint16_t*)img);
 }

libraries/Sipeed_OV2640/keywords.txt

@@ -18,7 +18,7 @@ setFrameSize         KEYWORD2
 run                  KEYWORD2
 id                   KEYWORD2
 snapshot             KEYWORD2
-setRotaion           KEYWORD2
+setRotation          KEYWORD2
 setInvert            KEYWORD2
 
 #######################################

libraries/Sipeed_OV2640/src/Sipeed_OV2640.cpp

@@ -599,7 +599,7 @@ static const uint8_t saturation_regs[NUM_SATURATION_LEVELS + 1][5] = {
 Sipeed_OV2640::Sipeed_OV2640( framesize_t frameSize, pixformat_t pixFormat)
 :Camera(frameSize, pixFormat),
 _dataBuffer(NULL), _aiBuffer(NULL),
-_resetPoliraty(ACTIVE_HIGH), _pwdnPoliraty(ACTIVE_HIGH),
+_resetPolarity(ACTIVE_HIGH), _pwdnPolarity(ACTIVE_HIGH),
 _slaveAddr(0x00),
 _id(0)
 {
@@ -611,7 +611,7 @@ _id(0)
 Sipeed_OV2640::Sipeed_OV2640(uint16_t width, uint16_t height, pixformat_t pixFormat)
 :Camera(width, height, pixFormat),
 _dataBuffer(NULL), _aiBuffer(NULL),
-_resetPoliraty(ACTIVE_HIGH), _pwdnPoliraty(ACTIVE_HIGH),
+_resetPolarity(ACTIVE_HIGH), _pwdnPolarity(ACTIVE_HIGH),
 _slaveAddr(0x00),
 _id(0)
 {
@@ -721,21 +721,24 @@ uint8_t* Sipeed_OV2640::snapshot()
     return _dataBuffer;
 }
 
-void Sipeed_OV2640::setRotaion(uint8_t rotation)
+void Sipeed_OV2640::setRotation(uint8_t rotation)
 {
-
+    //FIXME
 }
 
 void Sipeed_OV2640::setInvert(bool invert)
 {
-
+    //FIXME
+    ov2640_set_hmirror(!invert); 
+    //ov2640_set_vflip(1);
+    return;
 }
 
 
 
 int Sipeed_OV2640::dvpInit(uint32_t freq)
 {
-    // just support RGB565 and YUV442 on k210
+    // just support RGB565 and YUV422 on k210
     configASSERT(_pixFormat==PIXFORMAT_RGB565 || _pixFormat==PIXFORMAT_YUV422);
     _freq  = freq;
 
@@ -775,7 +778,7 @@ int Sipeed_OV2640::dvpInit(uint32_t freq)
     if(0 == sensor_ov_detect()){//find ov sensor
         // printf("find ov sensor\n");
     }
-    else if(0 == sensro_gc_detect()){//find gc0328 sensor
+    else if(0 == sensor_gc_detect()){//find gc0328 sensor
         // printf("find gc3028\n");
     }
 
@@ -874,7 +877,7 @@ int Sipeed_OV2640::sensor_ov_detect()
     if (_slaveAddr == 0) {
         /* Sensor has been held in reset,
            so the reset line is active low */
-        _resetPoliraty = ACTIVE_LOW;
+        _resetPolarity = ACTIVE_LOW;
 
         /* Pull the sensor out of the reset state,systick_sleep() */
         DCMI_RESET_HIGH();
@@ -883,14 +886,14 @@ int Sipeed_OV2640::sensor_ov_detect()
         /* Probe again to set the slave addr */
         _slaveAddr = cambus_scan();
         if (_slaveAddr == 0) {
-            _pwdnPoliraty = ACTIVE_LOW;
+            _pwdnPolarity = ACTIVE_LOW;
 
             DCMI_PWDN_HIGH();
             msleep(10);
 
             _slaveAddr = cambus_scan();
             if (_slaveAddr == 0) {
-                _resetPoliraty = ACTIVE_HIGH;
+                _resetPolarity = ACTIVE_HIGH;
 
                 DCMI_RESET_LOW();
                 msleep(10);
@@ -944,7 +947,7 @@ int Sipeed_OV2640::sensor_ov_detect()
     return 0;
 }
 
-int Sipeed_OV2640::sensro_gc_detect()
+int Sipeed_OV2640::sensor_gc_detect()
 {
     DCMI_PWDN_HIGH();//enable gc0328 要恢复 normal 工作模式，需将 PWDN pin 接入低电平即可，同时写入初始化寄存器即可
     DCMI_RESET_LOW();//reset gc3028
@@ -1485,6 +1488,38 @@ int Sipeed_OV2640::ov2640_set_vflip(int enable)
     return ret;
 }
 
+
+int Sipeed_OV2640::ov2640_set_flip(bool horiz, bool vert) 
+{
+	uint8_t reg;
+	int ret = cambus_readb(_slaveAddr, BANK_SEL, &reg);
+	ret |= cambus_writeb(_slaveAddr, BANK_SEL, reg | BANK_SEL_SENSOR);
+	ret |= cambus_readb(_slaveAddr, REG04, &reg);
+
+	if (horiz) {
+		reg |= REG04_HFLIP_IMG;
+		reg |= REG04_HREF_EN;
+	} 
+	else {
+		reg &= ~REG04_HFLIP_IMG;
+		reg &= ~REG04_HREF_EN;
+	}
+
+	if (vert) {
+		reg |= REG04_VFLIP_IMG;
+		reg |= REG04_VREF_EN;
+	} 
+	else {
+		reg &= ~REG04_VFLIP_IMG;
+		reg &= ~REG04_VREF_EN;
+	}
+
+	ret |= cambus_writeb(_slaveAddr, REG04, reg);
+
+	return ret;
+}
+
+
 int Sipeed_OV2640::reverse_u32pixel(uint32_t* addr,uint32_t length)
 {
   if(NULL == addr)
@@ -1519,3 +1554,6 @@ int Sipeed_OV2640::sensor_snapshot( )
     return 0;
 }
 
+int Sipeed_OV2640::flip( bool horiz, bool vert ) {
+	return ov2640_set_flip(horiz, vert);
+}

libraries/Sipeed_OV2640/src/Sipeed_OV2640.h

@@ -54,14 +54,16 @@ public:
     virtual uint8_t* snapshot();
     virtual uint16_t* getRGB565(){ return (uint16_t*)_dataBuffer; };
     virtual uint8_t* getRGB888(){ return _aiBuffer; };
-    virtual void setRotaion(uint8_t rotation);
+    virtual void setRotation(uint8_t rotation);
     virtual void setInvert(bool invert);
+    void flip(bool horiz, bool vert);
+
 
 private:
     uint8_t* _dataBuffer;    // put RGB565 data
     uint8_t* _aiBuffer;      // put RGB888 data
-    uint8_t  _resetPoliraty; // reset poliraty flag
-    uint8_t  _pwdnPoliraty;  // PWDN poliraty flag
+    uint8_t  _resetPolarity; // reset polarity flag
+    uint8_t  _pwdnPolarity;  // PWDN polarity flag
     uint8_t  _slaveAddr;     // camera address
     uint8_t  _id;
     uint32_t _freq;
@@ -80,7 +82,7 @@ private:
     int cambus_writew2(uint8_t slv_addr, uint16_t reg_addr, uint16_t reg_data);
 
     int sensor_ov_detect();
-    int sensro_gc_detect();
+    int sensor_gc_detect();
 
     int ov2640_reset();
     int ov2640_read_reg(uint8_t reg_addr);
@@ -103,6 +105,8 @@ private:
     int ov2640_get_rgb_gain_db(float *r_gain_db, float *g_gain_db, float *b_gain_db);
     int ov2640_set_hmirror(int enable);
     int ov2640_set_vflip(int enable);
+    int ov2640_set_flip(bool horiz, bool vert);
+
     int sensor_snapshot( );
     int reverse_u32pixel(uint32_t* addr,uint32_t length);
 

libraries/Ticker/keywords.txt

@@ -10,8 +10,10 @@ Ticker	KEYWORD1
 
 attach	KEYWORD2
 attach_ms	KEYWORD2
+attach_us	KEYWORD2
 once	KEYWORD2
 once_ms KEYWORD2
+once_us KEYWORD2
 detach	KEYWORD2
 
 #######################################	

libraries/Ticker/src/Ticker.cpp

@@ -25,6 +25,17 @@ Ticker::_attach_ms(uint32_t milliseconds, bool repeat, callback_with_arg_t callb
     sysctl_enable_irq();
 }
 
+void
+Ticker::_attach_us(uint32_t microseconds, bool repeat, callback_with_arg_t callback, size_t arg)
+{
+    user_callback = callback;
+    _arg = arg;
+    timer_set_interval(timer_device_number_t(timer_id), TIMER_CHANNEL_0, microseconds * 1000);
+    timer_irq_register(timer_device_number_t(timer_id), TIMER_CHANNEL_0, !repeat, 4, timer_callback, this);
+    timer_set_enable(timer_device_number_t(timer_id), TIMER_CHANNEL_0, 1);
+    sysctl_enable_irq();
+}
+
 void 
 Ticker::detach()
 {

libraries/Ticker/src/Ticker.h

@@ -32,6 +32,11 @@ public:
         _attach_ms(milliseconds, true, reinterpret_cast<callback_with_arg_t>(callback), 0);
     }
 
+    void attach_us(uint32_t microseconds, callback_t callback)
+    {
+        _attach_us(microseconds, true, reinterpret_cast<callback_with_arg_t>(callback), 0);
+    }
+
     template<typename TArg>
     void attach(float seconds, void (*callback)(TArg), TArg arg)
     {
@@ -48,6 +53,14 @@ public:
         _attach_ms(milliseconds, true, reinterpret_cast<callback_with_arg_t>(callback), arg32);
     }
 
+    template<typename TArg>
+    void attach_us(uint32_t microseconds, void (*callback)(TArg), TArg arg)
+    {
+        configASSERT(sizeof(TArg) <= sizeof(size_t));
+        size_t arg32 = (size_t)arg;
+        _attach_us(microseconds, true, reinterpret_cast<callback_with_arg_t>(callback), arg32);
+    }
+
     void once(float seconds, callback_t callback)
     {
         _attach_ms(seconds * 1000, false, reinterpret_cast<callback_with_arg_t>(callback), 0);
@@ -58,6 +71,11 @@ public:
         _attach_ms(milliseconds, false, reinterpret_cast<callback_with_arg_t>(callback), 0);	
     }
 
+    void once_us(uint32_t microseconds, callback_t callback)
+    {
+        _attach_us(microseconds, false, reinterpret_cast<callback_with_arg_t>(callback), 0);	
+    }
+
     template<typename TArg>
     void once(float seconds, void (*callback)(TArg), TArg arg)
     {
@@ -74,6 +92,14 @@ public:
         _attach_ms(milliseconds, false, reinterpret_cast<callback_with_arg_t>(callback), arg32);
     }
 
+    template<typename TArg>
+    void once_us(uint32_t microseconds, void (*callback)(TArg), TArg arg)
+    {
+        configASSERT(sizeof(TArg) <= sizeof(size_t));
+        size_t arg32 = (size_t)(arg);
+        _attach_us(microseconds, false, reinterpret_cast<callback_with_arg_t>(callback), arg32);
+    }
+
     void detach();
     bool active();
 
@@ -82,6 +108,7 @@ public:
 
 protected:
     void _attach_ms(uint32_t milliseconds, bool repeat, callback_with_arg_t callback, size_t arg);
+    void _attach_us(uint32_t microseconds, bool repeat, callback_with_arg_t callback, size_t arg);
 
 private:
     timer_id_t timer_id;

libraries/Wire/src/Wire.cpp

@@ -9,6 +9,9 @@ static int maix_i2c_slave_irq(void *userdata);
 
 TwoWire::TwoWire(i2c_device_number_t i2c_device)
 {
+    i2c_tx_buff = 0;
+    i2c_rx_buff = 0;
+
     _i2c_num = i2c_device;
     switch(i2c_device)
     {
@@ -38,44 +41,27 @@ TwoWire::~TwoWire()
 void 
 TwoWire::begin(uint8_t sda, uint8_t scl, uint32_t frequency)
 {
-    i2c_clk = frequency;
     fpioa_set_function(sda, sda_func);
     fpioa_set_function(scl, scl_func);
-    volatile i2c_t *i2c_adapter = i2c[_i2c_num];
-    uint8_t speed_mode = I2C_CON_SPEED_STANDARD;
-    //i2c_clk_init
+
     sysctl_clock_enable((sysctl_clock_t)(SYSCTL_CLOCK_I2C0 + _i2c_num));
     sysctl_clock_set_threshold((sysctl_threshold_t)(SYSCTL_THRESHOLD_I2C0 + _i2c_num), 3);
 
-    uint32_t v_i2c_freq = sysctl_clock_get_freq((sysctl_clock_t)(SYSCTL_CLOCK_I2C0 + _i2c_num));
-    uint16_t v_period_clk_cnt = floor( (v_i2c_freq*1.0 / i2c_clk / 2) + 0.5 );
-    
-
-    if(v_period_clk_cnt <= 6)
-        v_period_clk_cnt = 6;
-    if(v_period_clk_cnt >= 65525)//65535-10
-        v_period_clk_cnt = 65525;
-    if((i2c_clk>100000) && (i2c_clk<=1000000))
-        speed_mode = I2C_CON_SPEED_FAST;
-    else
-        speed_mode = I2C_CON_SPEED_HIGH;
+    volatile i2c_t *i2c_adapter = i2c[_i2c_num];
     i2c_adapter->enable = 0;
-    i2c_adapter->con = I2C_CON_MASTER_MODE | I2C_CON_SLAVE_DISABLE | I2C_CON_RESTART_EN |
-                       (address_width == 10 ? I2C_CON_10BITADDR_SLAVE : 0) | I2C_CON_SPEED(speed_mode);
-    i2c_adapter->ss_scl_hcnt = I2C_SS_SCL_HCNT_COUNT(v_period_clk_cnt);
-    i2c_adapter->ss_scl_lcnt = I2C_SS_SCL_LCNT_COUNT(v_period_clk_cnt);
-
     i2c_adapter->intr_mask = 0;
     i2c_adapter->dma_cr = 0x3;
     i2c_adapter->dma_rdlr = 0;
     i2c_adapter->dma_tdlr = 4;
-    i2c_adapter->enable = I2C_ENABLE_ENABLE;
+    
     is_master_mode = true;
     
+    delete i2c_tx_buff;
+    delete i2c_rx_buff;
     i2c_tx_buff = new RingBuffer();
     i2c_rx_buff = new RingBuffer();
 
-
+    setClock(frequency);
 }
     
 void 
@@ -83,12 +69,11 @@ TwoWire::begin(uint16_t slave_address, uint8_t sda, uint8_t scl)
 {
     fpioa_set_function(sda, sda_func);
     fpioa_set_function(scl, scl_func);
-
-    volatile i2c_t *i2c_adapter = i2c[_i2c_num];
     
     sysctl_clock_enable((sysctl_clock_t)(SYSCTL_CLOCK_I2C0 + _i2c_num));
     sysctl_clock_set_threshold((sysctl_threshold_t)(SYSCTL_THRESHOLD_I2C0 + _i2c_num), 3);
 
+    volatile i2c_t *i2c_adapter = i2c[_i2c_num];
     i2c_adapter->enable = 0;
     i2c_adapter->con =  I2C_CON_SPEED(1) | I2C_CON_STOP_DET_IFADDRESSED;
     i2c_adapter->ss_scl_hcnt = I2C_SS_SCL_HCNT_COUNT(37);
@@ -98,17 +83,20 @@ TwoWire::begin(uint16_t slave_address, uint8_t sda, uint8_t scl)
     i2c_adapter->tx_tl = I2C_TX_TL_VALUE(0);
     i2c_adapter->intr_mask = I2C_INTR_MASK_RX_FULL | I2C_INTR_MASK_START_DET | I2C_INTR_MASK_STOP_DET | I2C_INTR_MASK_RD_REQ;
 
+    is_master_mode = false;
+
     plic_set_priority((plic_irq_t)(IRQN_I2C0_INTERRUPT + _i2c_num), 1);
     plic_irq_register((plic_irq_t)(IRQN_I2C0_INTERRUPT + _i2c_num), maix_i2c_slave_irq, this);
     plic_irq_enable((plic_irq_t)(IRQN_I2C0_INTERRUPT + _i2c_num));
 
-    i2c_adapter->enable = I2C_ENABLE_ENABLE;
-    is_master_mode = false;
-
+    delete i2c_tx_buff;
+    delete i2c_rx_buff;
     i2c_tx_buff = new RingBuffer();
     i2c_rx_buff = new RingBuffer();
 
-}  
+    i2c_adapter->enable = I2C_ENABLE_ENABLE;
+}
+
 void
 TwoWire::setTimeOut(uint16_t timeOutMillis)
 {
@@ -145,7 +133,6 @@ TwoWire::setClock(uint32_t frequency)
     i2c_adapter->ss_scl_hcnt = I2C_SS_SCL_HCNT_COUNT(v_period_clk_cnt);
     i2c_adapter->ss_scl_lcnt = I2C_SS_SCL_LCNT_COUNT(v_period_clk_cnt);
     i2c_adapter->enable = I2C_ENABLE_ENABLE;
-
 }
 
 uint32_t 
@@ -236,6 +223,9 @@ TwoWire::readTransmission(uint16_t address, uint8_t* receive_buf, size_t receive
 void 
 TwoWire::beginTransmission(uint16_t address)
 {
+    // Clear buffers when new transation/packet starts
+    flush();
+
     transmitting = 1;
     txAddress = address;
 }
@@ -263,24 +253,28 @@ TwoWire::endTransmission(bool sendStop)  //结束时从rxbuff发送数据？
 uint8_t
 TwoWire::requestFrom(uint16_t address, uint8_t size, bool sendStop)  //请求数据，存入rxbuff，供read读
 {
+    // Clear buffers when new transation/packet starts
+    flush();
+
     int state,index = 0;
     uint8_t rx_data[RING_BUFFER_SIZE];
     state = readTransmission(address, rx_data, size, sendStop);
     if(0 == state){
-        while(size)
+        while(index < size)
         {
             i2c_rx_buff->store_char(rx_data[index++]); 
-            size--;
         }
+        return size;
     }
-    return state;
+    return 0;
 }
 
 size_t 
 TwoWire::write(uint8_t data) //写到txbuff
 {
-    if(transmitting) {
+    if(transmitting && !i2c_tx_buff->isFull()) {
         i2c_tx_buff->store_char(data);
+        return 1;
     }
     return 0;
 }
@@ -288,7 +282,7 @@ TwoWire::write(uint8_t data) //写到txbuff
 size_t 
 TwoWire::write(const uint8_t *data, int quantity)
 {
-    for(size_t i = 0; i < quantity; ++i) {
+    for(size_t i = 0; i < quantity; i++) {
         if(!write(data[i])) {
             return i;
         }

libraries/Wire/src/Wire.h

@@ -24,7 +24,7 @@ public:
 
     TwoWire(i2c_device_number_t i2c_device);
     ~TwoWire();
-    void begin(uint8_t sda = SDA, uint8_t scl = SCL, uint32_t frequency = 500000);
+    void begin(uint8_t sda = SDA, uint8_t scl = SCL, uint32_t frequency = 400000);
     void begin(uint16_t slave_address, uint8_t sda = SDA, uint8_t scl = SCL);
 
     void setClock(uint32_t frequency); 

package.json

@@ -1,6 +1,6 @@
 {
     "name": "framework-maixduino",
     "description": "Arduino Wiring-based Framework (K210 Core)",
-    "version": "0.3.8",
+    "version": "0.3.11",
     "url": "https://github.com/sipeed/Maixduino"
 }

platform.txt

@@ -1,9 +1,9 @@
-name = Maixduino
-version = 0.3.8
+name=Maixduino
+version=0.3.11
 
 # arch
-arch              = k210
-arch_for_c_cpp    = K210
+arch=k210
+arch_for_c_cpp=K210
 
 # Compile variables
 compiler.path={runtime.tools.riscv64-unknown-elf-gcc.path}/bin/
@@ -15,11 +15,10 @@ compiler.objcopy.cmd=riscv64-unknown-elf-objcopy
 compiler.elf2hex.cmd=riscv64-unknown-elf-objcopy
 compiler.size.cmd=riscv64-unknown-elf-size
 
-compiler.clib.path={runtime.tools.riscv64-unknown-elf-gcc.path}/include
 compiler.sdk.path={runtime.platform.path}/cores/arduino/kendryte-standalone-sdk/lib
 compiler.lib_hal_inc.path={runtime.platform.path}/cores/arduino/hal/include
 compiler.cores.path={runtime.platform.path}/cores/arduino/
-compiler.preproc.flags=-I{build.system.path}/include -I{compiler.cores.path} -I{compiler.lib_hal_inc.path} -I{compiler.sdk.path}/bsp/include -I{compiler.sdk.path}/drivers/include -I{compiler.sdk.path}/utils/include -I{compiler.sdk.path}/freertos/conf -I{compiler.sdk.path}/freertos/include -I{compiler.sdk.path}/freertos/portable -I{compiler.clib.path}
+compiler.preproc.flags="-I{build.system.path}/include" "-I{compiler.cores.path}" "-I{compiler.cores.path}/avr" "-I{compiler.lib_hal_inc.path}" "-I{compiler.sdk.path}/bsp/include" "-I{compiler.sdk.path}/drivers/include" "-I{compiler.sdk.path}/utils/include" "-I{compiler.sdk.path}/freertos/conf" "-I{compiler.sdk.path}/freertos/include" "-I{compiler.sdk.path}/freertos/portable"
 
 compiler.both.flags=-mcmodel=medany -mabi=lp64f -march=rv64imafc -fno-common -ffunction-sections -fdata-sections -fstrict-volatile-bitfields -fno-zero-initialized-in-bss -Os -ggdb -Wall -Werror=all -Wno-error=unused-function -Wno-error=unused-but-set-variable -Wno-error=unused-variable -Wno-error=deprecated-declarations -Wextra -Werror=frame-larger-than=65536 -Wno-unused-parameter -Wno-sign-compare -Wno-error=missing-braces -Wno-error=return-type -Wno-error=pointer-sign -Wno-missing-braces -Wno-strict-aliasing -Wno-implicit-fallthrough -Wno-missing-field-initializers -Wno-int-to-pointer-cast -Wno-error=comment -Wno-error=logical-not-parentheses -Wno-error=duplicate-decl-specifier -Wno-error=parentheses -Wno-error=narrowing -Wno-error=unused-value
 
@@ -27,7 +26,7 @@ compiler.debug.flags=-DCONFIG_LOG_ENABLE -DCONFIG_LOG_LEVEL=LOG_INFO -DDEBUG=1 -
 
 compiler.c.flags=-c {compiler.debug.flags} {compiler.both.flags} {compiler.preproc.flags} -std=gnu11 -Wno-pointer-to-int-cast -Wno-old-style-declaration -g -Wno-error=unused-variable -Wno-error=unused-function -Wno-error=unused-const-variable
 
-compiler.cpp.flags=-c {compiler.debug.flags} {compiler.both.flags} -I{runtime.platform.path}/libraries/SPI/src {compiler.preproc.flags} -std=gnu++17 -g -Wno-error=unused-variable -Wno-error=unused-function -Wno-error=unused-const-variable
+compiler.cpp.flags=-c {compiler.debug.flags} {compiler.both.flags} "-I{runtime.platform.path}/libraries/SPI/src" {compiler.preproc.flags} -std=gnu++17 -g -Wno-error=unused-variable -Wno-error=unused-function -Wno-error=unused-const-variable
 
 compiler.ld.flags=-mcmodel=medany -mabi=lp64f -march=rv64imafc -fno-common -ffunction-sections -fdata-sections -fstrict-volatile-bitfields -fno-zero-initialized-in-bss -Os -ggdb -nostartfiles -static -Wl,--gc-sections -Wl,-static -Wl,--whole-archive -Wl,--no-whole-archive -Wl,-EL -Wl,--no-relax -T {build.ldscript}
 

variants/ioxgd4/pins_arduino.h

@@ -0,0 +1,91 @@
+#ifndef _VARIANT_IOXGD4
+#define _VARIANT_IOXGD4
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* LEDs */
+#define PIN_LED_GREEN        13
+#define PIN_LED_BLUE         12
+#define PIN_LED_RED          14
+#define PIN_LED              13
+#define LED_BUILTIN          13
+#define LED_GREEN            13
+#define LED_BLUE             12
+#define LED_RED              14
+/* KEY */
+#define KEY0                 16
+/* MIC ARRAY */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DAT3             20
+#define MIC_DAT2             21
+#define MIC_DAT1             22
+#define MIC_DAT0             23
+#define MIC_LED_DAT          24
+/* SPI0 */
+#define SPI0_CS1             25
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+/* I2S */
+#define MIC0_WS              30
+#define MIC0_DATA            31
+#define MIC0_BCK             32
+#define I2S_WS               33
+#define I2S_DA               34
+#define I2S_BCK              35
+/* LCD */
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+#define RX0                   4
+#define TX0                   5
+
+#define RX1                   7
+#define TX1                   6
+
+#define SDA                  33
+#define SCL                  32
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+}pwm_fpio_set_t;
+
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/lamloei_aiot_daan/pins_arduino.h

@@ -1,5 +1,5 @@
-#ifndef _VARIANT_SIPEED_M1_DOCK
-#define _VARIANT_SIPEED_M1_DOCK
+#ifndef _VARIANT_LAMLOEI_AIOT_DAAN
+#define _VARIANT_LAMLOEI_AIOT_DAAN
 
 #include <stdint.h>
 
@@ -65,6 +65,9 @@ extern class UARTClass Serial3;
 #define SDA                  31
 #define SCL                  30
 
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
 static const uint8_t SS   = SPI0_CS0 ;
 static const uint8_t MOSI = SPI0_MOSI;
 static const uint8_t MISO = SPI0_MISO;

variants/m5stack_m5stick_v/pins_arduino.h

@@ -0,0 +1,93 @@
+#ifndef _VARIANT_M5STACK_M5STICK_V
+#define _VARIANT_M5STACK_M5STICK_V
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UART */
+#define RX0                   4
+#define TX0                   5
+/* LEDs */
+#define PIN_LED_RED           6
+#define PIN_LED_WHITE         7
+#define PIN_LED_BLUE          8
+#define PIN_LED_GREEN         9
+#define PIN_LED               9
+#define LED_RED               6
+#define LED_WHITE             7
+#define LED_BLUE              8
+#define LED_GREEN             9
+#define LED_BUILTIN           9
+/* MIC ARRAY */
+#define MIC_WS               10
+#define MIC_DAT3             12
+#define MIC_BCK              13
+/* SPK MAX98357 */
+#define I2S_SD               11
+#define I2S_LRCLK            14
+#define I2S_BCLK             15
+#define I2S_DIN              17
+/* LCD ST7789 135x240 */
+#define LCD_SDA              18
+#define LCD_SCL              19
+#define LCD_DC               20
+#define LCD_RST              21
+#define LCD_CS               22
+/* AXP192 INT PIN */
+#define INTL_INT             23
+/* INTL I2C - AXP192, MPU6886 */
+#define SCL                  28
+#define SDA                  29
+/* SPI0 */
+#define SPI0_SCLK            30
+#define SPI0_MISO            31
+#define SPI0_CS0             32
+#define SPI0_MOSI            33
+/* GROVE */
+#define RX1                  34
+#define TX1                  35
+#define EXTL_SCL             34
+#define EXTL_SDA             35
+/* BUTTONS */
+#define BTN_A                36
+#define BTN_B                37
+#define KEY0                 36
+#define KEY1                 37
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+} pwm_fpio_set_t;
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/m5stack_m5unit_v/pins_arduino.h

@@ -0,0 +1,78 @@
+#ifndef _VARIANT_M5STACK_M5UNIT_V
+#define _VARIANT_M5STACK_M5UNIT_V
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UART */
+#define RX0                   4
+#define TX0                   5
+/* WS2812 LEDs */
+#define PIN_LED_RGB           8
+
+/* MIC ARRAY */
+#define MIC_WS               10
+#define MIC_DAT3             12
+#define MIC_BCK              13
+/* SPK MAX98357 */
+#define SPK_LRCLK            14
+#define SPK_BCLK             15
+#define SPK_DIN              17
+#define SPK_SD               25
+/* BUTTONS */
+#define BTN_A                18
+#define BTN_B                19
+#define KEY0                 18
+#define KEY1                 19
+/* AXP192 INT PIN */
+#define AXP_INT              23
+/* INTL I2C */
+#define SCL                  28
+#define SDA                  29
+/* SPI0 */
+#define SPI0_SCLK            30
+#define SPI0_MISO            31
+#define SPI0_CS0             32
+#define SPI0_MOSI            33
+/* EXTL I2C */
+#define EXTL_SCL             34
+#define EXTL_SDA             35
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+}pwm_fpio_set_t;
+ 
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_amigo/pins_arduino.h

@@ -0,0 +1,96 @@
+#ifndef _VARIANT_SIPEED_MAIX_AMIGO
+#define _VARIANT_SIPEED_MAIX_AMIGO
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS CH552T */
+#define RX0                   4
+#define TX0                   5
+/* UART Grove */
+#define RX1                   9 //Grove
+#define TX1                   7 //Grove
+/* 8P Connector */
+// #define PB0                   8 //8P-12
+// #define PB1                  12 //8P-3
+/* SPI0 */
+#define SPI0_MISO             6 //8P-11
+#define SPI0_MOSI            10 //8P-2
+#define SPI0_SCLK            11 //8P-1
+#define SPI0_CS0             26 //TF
+/* KEYs */
+#define KEY2                 20 //Grove
+#define KEY1                 23 //Grove      
+/* LEDs */
+#define PIN_LED_RED          14
+#define PIN_LED_GREEN        15
+#define PIN_LED_BLUE         17
+#define PIN_LED              15
+#define LED_RED              14
+#define LED_GREEN            15
+#define LED_BLUE             17
+#define LED_BUILTIN          15
+/* UART3 */
+#define TX2                  22 //8P-4
+#define RX2                  25 //8P-5
+/* I2C1 - AXP173, MSA301, TOUCH */
+#define SCL                  24
+#define SDA                  27
+/* USB_SBU */
+#define USB_DP               28 //8P-8
+#define USB_DM               29 //8P-9
+/* I2S AUDIO CODEC ES8374 */
+#define I2S2_MCLK            13
+#define I2S2_WS              18
+#define I2S2_SCLK            21
+#define I2S2_DOUT            34
+#define I2S2_DIN             35
+/* Flash LED */
+#define WLED_EN              32
+/* TouchScreen */
+#define CAP_TOUCH_IRQ        33
+/* LCD */
+#define LCD_TEN              19
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+} pwm_fpio_set_t;
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_bit/pins_arduino.h

@@ -0,0 +1,96 @@
+#ifndef _VARIANT_SIPEED_MAIX_BIT
+#define _VARIANT_SIPEED_MAIX_BIT
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS */
+#define RX0                   4
+#define TX0                   5
+/* UART */
+#define RX1                   6
+#define TX1                   7
+
+// #define IO_8                  8
+// #define IO_9                  9
+// #define IO_10                10
+/* LEDs */
+#define PIN_LED_GREEN        12
+#define PIN_LED_RED          13
+#define PIN_LED_BLUE         14
+#define PIN_LED              12
+#define LED_RED              13
+#define LED_GREEN            12
+#define LED_BLUE             14
+#define LED_BUILTIN          12
+// #define IO_15                15
+// #define IO_17                17
+
+/* I2S MIC */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DAT3             20
+
+// #define IO_21                21
+// #define IO_22                22
+// #define IO_23                23
+// #define IO_24                24
+// #define IO_25                25
+/* SPI0 */
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+
+// #define SCL                  30
+// #define SDA                  31
+// #define IO_30                30
+// #define IO_31                31
+// #define IO_32                32
+// #define IO_33                33
+// #define IO_34                34
+// #define IO_35                35
+/* LCD */
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+} pwm_fpio_set_t;
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_bit_mic/pins_arduino.h

@@ -0,0 +1,94 @@
+#ifndef _VARIANT_SIPEED_MAIX_BIT_MIC
+#define _VARIANT_SIPEED_MAIX_BIT_MIC
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS */
+#define RX0                   4
+#define TX0                   5
+/* UART */
+#define RX1                   6
+#define TX1                   7
+
+#define IO_8                  8
+#define IO_9                  9
+#define IO_10                10
+/* LEDs */
+#define PIN_LED_GREEN        12
+#define PIN_LED_RED          13
+#define PIN_LED_BLUE         14
+#define PIN_LED              12
+#define LED_RED              13
+#define LED_GREEN            12
+#define LED_BLUE             14
+#define LED_BUILTIN          12
+// #define IO_15                15
+// #define IO_17                17
+/* I2S MIC */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DAT3             20
+// #define IO_21                21
+// #define IO_22                22
+// #define IO_23                23
+// #define IO_24                24
+// #define IO_25                25
+/* SPI0 */
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+
+// #define SCL                  30
+// #define SDA                  31
+// #define IO_30                30
+// #define IO_31                31
+// #define IO_32                32
+// #define IO_33                33
+// #define IO_34                34
+// #define IO_35                35
+/* LCD */
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+} pwm_fpio_set_t;
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_cube/pins_arduino.h

@@ -0,0 +1,99 @@
+#ifndef _VARIANT_SIPEED_MAIX_CUBE
+#define _VARIANT_SIPEED_MAIX_CUBE
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS CH552T */
+#define RX0                   4
+#define TX0                   5
+/* SPMOD */
+#define RX1                   6
+#define TX1                   7
+// #define IO_8                  8
+// #define IO_9                  9
+/* KEYs */
+#define KEY1                 10
+#define KEY2                 11
+#define PIN_KEY_DOWN         10
+#define PIN_KEY_UP           11
+/* LEDs */
+#define PIN_LED_GREEN        12
+#define PIN_LED_RED          13
+#define PIN_LED_BLUE         14
+#define PIN_LED              12
+#define LED_RED              13
+#define LED_GREEN            12
+#define LED_BLUE             14
+#define LED_BUILTIN          12
+/* SPMOD */
+// #define IO_15                15
+// #define IO_20                20
+// #define IO_21                21
+/* I2S AUDIO CODEC ES8374 */
+#define I2S_DIN              18
+#define I2S_MCLK             19
+#define I2S_LRCK             33
+#define I2S_DOUT             34
+#define I2S_SCLK             35
+/* USB_SBU */
+// #define IO_22                22
+// #define IO_23                23
+/* GROVE */
+// #define IO_24                24
+// #define IO_25                25
+/* SPI0 */
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+/* I2C1 - AXP173, MSA301*/
+#define SCL                  30
+#define SDA                  31
+/* Flash LED */
+#define WLED_EN              32
+/* LCD */
+#define LCD_BL               17
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+} pwm_fpio_set_t;
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_go/pins_arduino.h

@@ -1,5 +1,5 @@
-#ifndef _VARIANT_BOARD_SIPEED_MAIX_GO
-#define _VARIANT_BOARD_SIPEED_MAIX_GO
+#ifndef _VARIANT_SIPEED_MAIX_GO
+#define _VARIANT_SIPEED_MAIX_GO
 
 #include <stdint.h>
 
@@ -18,21 +18,37 @@ extern class UARTClass Serial3;
 #endif
 
 /* BOARD  PIN DEFINE */
+/* UARTHS */
+#define RX0                   4
+#define TX0                   5
+/* WIFI UART1 */
+#define RX1                   6
+#define TX1                   7
+#define ESP_TX                6
+#define ESP_RX                7
+#define ESP_EN                8
+/* BPSK */
+#define BPSK_P                9
+#define BPSK_N               10
+// #define IO_11                11
 /* LEDs */
-#define PIN_LED_GREEN        13
 #define PIN_LED_BLUE         12
+#define PIN_LED_GREEN        13
 #define PIN_LED_RED          14
 #define PIN_LED              13
-#define LED_BUILTIN          13
+#define LED_RED              14
 #define LED_GREEN            13
 #define LED_BLUE             12
-#define LED_RED              14
+#define LED_BUILTIN          13
 /* KEY */
-#define KEY0                 15
-#define PIN_KEY_DOWN         16
+#define KEY1                 15
+#define KEY0                 16
+#define KEY2                 17
+#define PIN_KEY_DOWN         15
+#define PIN_KEY_PRESS        16
 #define PIN_KEY_UP           17
-#define PIN_KEY_PRESS        15
 /* MIC ARRAY */
+/* I2S MIC MSM261S4030H0 */
 #define MIC_BCK              18
 #define MIC_WS               19
 #define MIC_DAT3             20
@@ -40,16 +56,17 @@ extern class UARTClass Serial3;
 #define MIC_DAT1             22
 #define MIC_DAT0             23
 #define MIC_LED_DAT          24
-/* SPI0 */
-#define SPI0_CS1             25
+#define MIC_LED_CLK          25
+/* SPI0 TF */
 #define SPI0_MISO            26
 #define SPI0_SCLK            27
 #define SPI0_MOSI            28
 #define SPI0_CS0             29
-/* I2S */
-#define MIC0_WS              30
-#define MIC0_DATA            31
-#define MIC0_BCK             32
+/* I2C1 MSA300 */
+#define SCL                  30
+#define SDA                  31
+// #define IO_32                32
+/* I2S DAC PT8211 */
 #define I2S_WS               33
 #define I2S_DA               34
 #define I2S_BCK              35
@@ -59,14 +76,9 @@ extern class UARTClass Serial3;
 #define LCD_DC               38
 #define LCD_WR               39
 
-#define RX0                   4
-#define TX0                   5
 
-#define RX1                   6
-#define TX1                   7
-
-#define SDA                  31
-#define SCL                  30
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
 
 static const uint8_t SS   = SPI0_CS0 ;
 static const uint8_t MOSI = SPI0_MOSI;
@@ -77,8 +89,7 @@ typedef struct _pwm_fpio_set_t{
     pwm_channel_number_t channel;
     pwm_device_number_t device;
     uint8_t inuse;
-}pwm_fpio_set_t;
-
+} pwm_fpio_set_t;
 
 
 #define VARIANT_NUM_GPIOHS (32)

variants/sipeed_maix_one_dock/pins_arduino.h

@@ -0,0 +1,89 @@
+#ifndef _VARIANT_SIPEED_MAIX_ONE_DOCK
+#define _VARIANT_SIPEED_MAIX_ONE_DOCK
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS */
+#define RX0                   4
+#define TX0                   5
+/* WIFI UART1 */
+#define RX1                   6
+#define TX1                   7
+/* LEDs */
+#define PIN_LED_GREEN        13
+#define PIN_LED_BLUE         12
+#define PIN_LED_RED          14
+#define PIN_LED              13
+#define LED_RED              14
+#define LED_GREEN            13
+#define LED_BLUE             12
+#define LED_BUILTIN          13
+/* KEY */
+//#define KEY0                 16
+/* MIC ARRAY */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DAT3             20
+#define MIC_DAT2             21
+#define MIC_DAT1             22
+#define MIC_DAT0             23
+#define MIC_LED_DAT          24
+/* SPI0 */
+#define SPI0_CS1             25
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+/* I2S */
+#define MIC0_WS              30
+#define MIC0_DATA            31
+#define MIC0_BCK             32
+#define I2S_WS               33
+#define I2S_DA               34
+#define I2S_BCK              35
+/* LCD */
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+}pwm_fpio_set_t;
+
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maix_one_w_dock/pins_arduino.h

@@ -0,0 +1,90 @@
+#ifndef _VARIANT_SIPEED_MAIX_ONE_W_DOCK
+#define _VARIANT_SIPEED_MAIX_ONE_W_DOCK
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+/* UARTHS */
+#define RX0                   4
+#define TX0                   5
+/* WIFI UART1 */
+#define RX1                   6
+#define TX1                   7
+/* LEDs */
+#define PIN_LED_RED          14
+#define PIN_LED_GREEN        13
+#define PIN_LED_BLUE         12
+#define PIN_LED              13
+#define LED_RED              14
+#define LED_GREEN            13
+#define LED_BLUE             12
+#define LED_BUILTIN          13
+/* KEY */
+//#define KEY0                 16
+/* MIC ARRAY */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DAT3             20
+#define MIC_DAT2             21
+#define MIC_DAT1             22
+#define MIC_DAT0             23
+#define MIC_LED_DAT          24
+/* SPI0 */
+#define SPI0_CS1             25
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+/* I2S */
+#define MIC0_WS              30
+#define MIC0_DATA            31
+#define MIC0_BCK             32
+
+#define I2S_WS               33
+#define I2S_DA               34
+#define I2S_BCK              35
+/* LCD */
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+#define MD_PIN_MAP(fpio)   (fpio)
+#define ORG_PIN_MAP(org_pin)    (org_pin)
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+}pwm_fpio_set_t;
+
+
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif

variants/sipeed_maixduino/pins_arduino.h

@@ -0,0 +1,104 @@
+#ifndef _VARIANT_SIPEED_MAIXDUINO
+#define _VARIANT_SIPEED_MAIXDUINO
+
+#include <stdint.h>
+
+#define RISCV
+#include "platform.h"
+
+#include "Arduino.h"
+#include "pwm.h"
+
+#ifdef __cplusplus
+#include "UARTClass.h"
+extern class UARTHSClass Serial;
+extern class UARTClass Serial1;
+extern class UARTClass Serial2;
+extern class UARTClass Serial3;
+#endif
+
+/* BOARD  PIN DEFINE */
+#define RX0                   0
+#define TX0                   1
+/* LEDs (USE Builtin TX PIN led)*/
+#define PIN_LED_RED          13
+#define PIN_LED_GREEN        12
+#define PIN_LED_BLUE         14
+#define PIN_LED              12
+#define LED_RED              13
+#define LED_GREEN            12
+#define LED_BLUE             14
+#define LED_BUILTIN          12
+/* KEY */
+//#define KEY0                 16
+/* ONBOARD ESP32 */
+#define ESP_TX                6
+#define ESP_RX                7
+#define ESP_EN                8
+#define ESP_READY             9
+#define ESP_SPI_CS           25
+/* SPI0 */
+#define SPI0_MISO            26
+#define SPI0_SCLK            27
+#define SPI0_MOSI            28
+#define SPI0_CS0             29
+/* I2S */
+#define MIC_BCK              18
+#define MIC_WS               19
+#define MIC_DATA             20
+/* I2C1 */
+#define SCL                  30
+#define SDA                  31
+/* DAC PT8211 */
+#define I2S_WS               33
+#define I2S_DA               34
+#define I2S_BCK              35
+/* LCD */
+#define LCD_BL               17
+#define LCD_CS               36
+#define LCD_RST              37
+#define LCD_DC               38
+#define LCD_WR               39
+
+
+static const uint8_t SS   = SPI0_CS0 ;
+static const uint8_t MOSI = SPI0_MOSI;
+static const uint8_t MISO = SPI0_MISO;
+static const uint8_t SCK  = SPI0_SCLK;
+
+typedef struct _pwm_fpio_set_t{
+    pwm_channel_number_t channel;
+    pwm_device_number_t device;
+    uint8_t inuse;
+}pwm_fpio_set_t;
+
+#define MD_PIN_MAP(fpio) (((fpio) < 17) ? _maixduino_pin_map[(fpio)] : (fpio))
+
+static const uint8_t _maixduino_pin_map[17] = {4, 5, 21, 22, 23, 24, 32, 15, 14, 13, 12, 11, 10, 3, 31, 30, 16};
+
+#define ORG_PIN_MAP(org_pin) _original_pin_map[(org_pin)]
+
+static const uint8_t _original_pin_map[48] = {255, 255, 255, 13,  0,   1,   255, 255, 255, 255, 
+                                              12,  11,  10,  9,   8,   7,   16, 255, 255, 255, 
+                                              255, 2,   3,   4,   5,   255, 255, 255, 255, 255, 
+                                              15,  14,  6,   255, 255, 255, 255, 255, 255, 255, 
+                                              255, 255, 255, 255, 255, 255, 255, 255};
+
+typedef enum _analog_output_pin_t{
+    A0,
+    A1,
+    A2,
+    A3,
+    A4,
+    A5,
+    ANALOG_OUTPUT_PIN_MAX,
+}analog_output_pin_t;
+
+#define VARIANT_NUM_GPIOHS (32)
+#define VARIANT_NUM_GPIO   ( 8)
+#define VARIANT_NUM_PWM    (12)
+#define VARIANT_NUM_I2C    ( 3)
+#define VARIANT_NUM_SPI    ( 3)
+#define VARIANT_NUM_UART   ( 3)
+
+#endif