[SYS] Update arduino core to 3.1.1 + refactor ino to cpp (#2177)

* Update arduino core to 3.1.1 * Fix Blufi build * Update arduinojson, fix build errors with idf * Fix narrowing * fix RF builds * WIP-Convert ino files to cpp * Fix pilight build * Fix Somfy actuator build. * Update esp32dev-rf partition * Fix Weatherstation build * Fix GFSunInverter build * Fix esp32dev-ir build * Fix ble-aws build * Fix eth builds * Fix m5Stack missing pins_arduino.h * Fix build errors for M5 stack/tough, others are upstream issues. * Fix RTL 433 build - remaining errors are from radolib * Fix nodemcu build * fix 2g builds * Fix serial build * Fix actuator on off builds * Fix SSD1306 build - remaining errors are from radiolib * Fix multiple definition of OTAserver_cert * Fix nodemcu rf2 build * Fix ADC builds * Fix sensor builds * Fix LORA builds * Fix multi-receiver builds - remaining errors are in radiolib * Fix fastled builds * Fix theegns board builds * Fix broker builds * Update fastled - old version failed all-test build * Fix RN8209 builds * Fix max temp actuator builds * Fix PWM builds * Fix C37 sensor builds * Fix HTU21 builds * Fix INA266 builds * Fix undefined variables in mqtt discovery * Fix webui build * Fix fastled invalid pin error * Fix wifi manual setup builds * Fix onewire/all-test build - bin too big error remaining * Fix theengs plug build * Fix rfbridge builds * Fix blufi builds * Fix undefined functions in serial * Fix preprocessor definition checks * Set IDF log level to erre * Add delay in loop to prevent watchdog timeout * Use xTaskCreateUniveral to support single core processors * Remove old HTTPUpdate files - upsteam fixed. * Cleanup and move common declarations to header file * Use custom partiton table to fix builds where bin is too large * Update M5StickC - fixs esp32-m5stick-c-ble build * Revert to Arduino core 2.x for builds with incompatible libs * Remove "Z" from file names and rename omg_common to TheengsCommon * Fix gateway name when using MAC with new Arduino core * Update IDF config to reduce loop task stack use * Update esp-nimble-cpp version, corrects BLE uppercase ID's * Update wifi manager to fix watchdog timeout error
2026-03-03 14:05:43 +01:00 · 2025-05-06 18:35:50 -06:00
parent 6e77efb11b
commit 585df9a420
83 changed files with 1275 additions and 1293 deletions
--- a/main/sensorGPIOKeyCode.cpp
+++ b/main/sensorGPIOKeyCode.cpp
@@ -0,0 +1,81 @@
+/*  
+  Theengs OpenMQTTGateway - We Unite Sensors in One Open-Source Interface
+   Act as a gateway between your 433mhz, infrared IR, BLE, LoRa signal and one interface like an MQTT broker 
+   Send and receiving command by MQTT
+ 
+    GPIO KeyCode derived from  GPIO Input
+
+    This reads up to 4 gpio with latch signal (gpio line) and combines the bits as KeyKode - can be connected
+    to EV1527 receiver.
+
+    Copyright: (c)Grzegorz Rajtar
+    
+    This file is part of OpenMQTTGateway.
+    
+    OpenMQTTGateway is free software: you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation, either version 3 of the License, or
+    (at your option) any later version.
+    OpenMQTTGateway is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+    You should have received a copy of the GNU General Public License
+    along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#include "User_config.h"
+
+#ifdef ZsensorGPIOKeyCode
+#  include "TheengsCommon.h"
+#  include "config_GPIOKeyCode.h"
+
+int InputStateGPIOKeyCode = 0x0f; // Set to 3 so that it reads on startup
+int lastInputStateGPIOKeyCode = 0x0f;
+int lastLatchStateGPIOKeyCode = 0;
+
+void setupGPIOKeyCode() {
+  pinMode(GPIOKeyCode_LATCH_GPIO, INPUT_PULLUP); //
+  pinMode(GPIOKeyCode_D0_GPIO, INPUT_PULLUP); //
+  pinMode(GPIOKeyCode_D1_GPIO, INPUT_PULLUP); //
+  pinMode(GPIOKeyCode_D2_GPIO, INPUT_PULLUP); //
+  //pinMode(GPIOKeyCode_D3_GPIO, INPUT_PULLUP);     //
+}
+
+void MeasureGPIOKeyCode() {
+  int latch = digitalRead(GPIOKeyCode_LATCH_GPIO);
+
+  // check to see if you just pressed the button
+  // (i.e. the input went from LOW to HIGH), and you've waited long enough
+  // since the last press to ignore any noise:
+
+  {
+    // whatever the reading is at, it's been there for longer than the debounce
+    // delay, so take it as the actual current state:
+    yield();
+    // if the Input state has changed:
+    if (latch > 0 && lastLatchStateGPIOKeyCode != latch) {
+      int reading = digitalRead(GPIOKeyCode_D0_GPIO) | (digitalRead(GPIOKeyCode_D1_GPIO) << 1) | (digitalRead(GPIOKeyCode_D2_GPIO) << 2);
+      //| digitalRead(GPIOKeyCode_D3_GPIO) << 3;
+
+      char hex[3];
+
+      InputStateGPIOKeyCode = reading;
+      sprintf(hex, "%02x", InputStateGPIOKeyCode);
+      hex[2] = 0;
+      Log.notice(F("GPIOKeyCode %H" CR), hex);
+      pub(subjectGPIOKeyCodetoMQTT, hex);
+      lastLatchStateGPIOKeyCode = latch;
+    }
+
+    if (latch != lastLatchStateGPIOKeyCode) {
+      lastLatchStateGPIOKeyCode = latch;
+      Log.notice(F("GPIOKeyCode latch %d" CR), latch);
+      if (latch == 0)
+        pub(subjectGPIOKeyCodeStatetoMQTT, "done");
+    }
+
+    // save the reading. Next time through the loop, it'll be the lastInputState:
+    lastInputStateGPIOKeyCode = InputStateGPIOKeyCode;
+  }
+}
+#endif