mirror of
https://github.com/1technophile/OpenMQTTGateway.git
synced 2026-03-02 21:44:21 +01:00
585df9a420
* Update arduino core to 3.1.1 * Fix Blufi build * Update arduinojson, fix build errors with idf * Fix narrowing * fix RF builds * WIP-Convert ino files to cpp * Fix pilight build * Fix Somfy actuator build. * Update esp32dev-rf partition * Fix Weatherstation build * Fix GFSunInverter build * Fix esp32dev-ir build * Fix ble-aws build * Fix eth builds * Fix m5Stack missing pins_arduino.h * Fix build errors for M5 stack/tough, others are upstream issues. * Fix RTL 433 build - remaining errors are from radolib * Fix nodemcu build * fix 2g builds * Fix serial build * Fix actuator on off builds * Fix SSD1306 build - remaining errors are from radiolib * Fix multiple definition of OTAserver_cert * Fix nodemcu rf2 build * Fix ADC builds * Fix sensor builds * Fix LORA builds * Fix multi-receiver builds - remaining errors are in radiolib * Fix fastled builds * Fix theegns board builds * Fix broker builds * Update fastled - old version failed all-test build * Fix RN8209 builds * Fix max temp actuator builds * Fix PWM builds * Fix C37 sensor builds * Fix HTU21 builds * Fix INA266 builds * Fix undefined variables in mqtt discovery * Fix webui build * Fix fastled invalid pin error * Fix wifi manual setup builds * Fix onewire/all-test build - bin too big error remaining * Fix theengs plug build * Fix rfbridge builds * Fix blufi builds * Fix undefined functions in serial * Fix preprocessor definition checks * Set IDF log level to erre * Add delay in loop to prevent watchdog timeout * Use xTaskCreateUniveral to support single core processors * Remove old HTTPUpdate files - upsteam fixed. * Cleanup and move common declarations to header file * Use custom partiton table to fix builds where bin is too large * Update M5StickC - fixs esp32-m5stick-c-ble build * Revert to Arduino core 2.x for builds with incompatible libs * Remove "Z" from file names and rename omg_common to TheengsCommon * Fix gateway name when using MAC with new Arduino core * Update IDF config to reduce loop task stack use * Update esp-nimble-cpp version, corrects BLE uppercase ID's * Update wifi manager to fix watchdog timeout error
82 lines
3.0 KiB
C++
82 lines
3.0 KiB
C++
/*
|
|
Theengs OpenMQTTGateway - We Unite Sensors in One Open-Source Interface
|
|
Act as a gateway between your 433mhz, infrared IR, BLE, LoRa signal and one interface like an MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
GPIO KeyCode derived from GPIO Input
|
|
|
|
This reads up to 4 gpio with latch signal (gpio line) and combines the bits as KeyKode - can be connected
|
|
to EV1527 receiver.
|
|
|
|
Copyright: (c)Grzegorz Rajtar
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#include "User_config.h"
|
|
|
|
#ifdef ZsensorGPIOKeyCode
|
|
# include "TheengsCommon.h"
|
|
# include "config_GPIOKeyCode.h"
|
|
|
|
int InputStateGPIOKeyCode = 0x0f; // Set to 3 so that it reads on startup
|
|
int lastInputStateGPIOKeyCode = 0x0f;
|
|
int lastLatchStateGPIOKeyCode = 0;
|
|
|
|
void setupGPIOKeyCode() {
|
|
pinMode(GPIOKeyCode_LATCH_GPIO, INPUT_PULLUP); //
|
|
pinMode(GPIOKeyCode_D0_GPIO, INPUT_PULLUP); //
|
|
pinMode(GPIOKeyCode_D1_GPIO, INPUT_PULLUP); //
|
|
pinMode(GPIOKeyCode_D2_GPIO, INPUT_PULLUP); //
|
|
//pinMode(GPIOKeyCode_D3_GPIO, INPUT_PULLUP); //
|
|
}
|
|
|
|
void MeasureGPIOKeyCode() {
|
|
int latch = digitalRead(GPIOKeyCode_LATCH_GPIO);
|
|
|
|
// check to see if you just pressed the button
|
|
// (i.e. the input went from LOW to HIGH), and you've waited long enough
|
|
// since the last press to ignore any noise:
|
|
|
|
{
|
|
// whatever the reading is at, it's been there for longer than the debounce
|
|
// delay, so take it as the actual current state:
|
|
yield();
|
|
// if the Input state has changed:
|
|
if (latch > 0 && lastLatchStateGPIOKeyCode != latch) {
|
|
int reading = digitalRead(GPIOKeyCode_D0_GPIO) | (digitalRead(GPIOKeyCode_D1_GPIO) << 1) | (digitalRead(GPIOKeyCode_D2_GPIO) << 2);
|
|
//| digitalRead(GPIOKeyCode_D3_GPIO) << 3;
|
|
|
|
char hex[3];
|
|
|
|
InputStateGPIOKeyCode = reading;
|
|
sprintf(hex, "%02x", InputStateGPIOKeyCode);
|
|
hex[2] = 0;
|
|
Log.notice(F("GPIOKeyCode %H" CR), hex);
|
|
pub(subjectGPIOKeyCodetoMQTT, hex);
|
|
lastLatchStateGPIOKeyCode = latch;
|
|
}
|
|
|
|
if (latch != lastLatchStateGPIOKeyCode) {
|
|
lastLatchStateGPIOKeyCode = latch;
|
|
Log.notice(F("GPIOKeyCode latch %d" CR), latch);
|
|
if (latch == 0)
|
|
pub(subjectGPIOKeyCodeStatetoMQTT, "done");
|
|
}
|
|
|
|
// save the reading. Next time through the loop, it'll be the lastInputState:
|
|
lastInputStateGPIOKeyCode = InputStateGPIOKeyCode;
|
|
}
|
|
}
|
|
#endif
|