🔖 Version 2.1.2.7

🔨 Preflight check for future config (#28320 )
Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>
2026-02-03 23:49:37 -06:00 · 2026-02-03 23:49:37 -06:00 · 2026-01-22 21:40:56 -06:00 · 2026-01-22 10:44:31 -06:00 · 2026-01-22 10:44:31 -06:00 · 2026-01-22 10:44:31 -06:00
79 changed files with 1073 additions and 48553 deletions
--- a/Marlin/Configuration.h
+++ b/Marlin/Configuration.h
@@ -35,7 +35,7 @@
 *
 * Advanced settings can be found in Configuration_adv.h
 */
-#define CONFIGURATION_H_VERSION 02010205
+#define CONFIGURATION_H_VERSION 02010206

 //===========================================================================
 //============================= Getting Started =============================
@@ -682,13 +682,13 @@
  #if ENABLED(PID_PARAMS_PER_HOTEND)
    // Specify up to one value per hotend here, according to your setup.
    // If there are fewer values, the last one applies to the remaining hotends.
-    #define DEFAULT_Kp_LIST {  22.20,  22.20 }
-    #define DEFAULT_Ki_LIST {   1.08,   1.08 }
-    #define DEFAULT_Kd_LIST { 114.00, 114.00 }
+    #define DEFAULT_KP_LIST {  22.20,  22.20 }
+    #define DEFAULT_KI_LIST {   1.08,   1.08 }
+    #define DEFAULT_KD_LIST { 114.00, 114.00 }
  #else
-    #define DEFAULT_Kp  22.20
-    #define DEFAULT_Ki   1.08
-    #define DEFAULT_Kd 114.00
+    #define DEFAULT_KP  22.20
+    #define DEFAULT_KI   1.08
+    #define DEFAULT_KD 114.00
  #endif
 #else
  #define BANG_MAX 255    // Limit hotend current while in bang-bang mode; 255=full current
@@ -775,9 +775,9 @@

  // 120V 250W silicone heater into 4mm borosilicate (MendelMax 1.5+)
  // from FOPDT model - kp=.39 Tp=405 Tdead=66, Tc set to 79.2, aggressive factor of .15 (vs .1, 1, 10)
-  #define DEFAULT_bedKp 10.00
-  #define DEFAULT_bedKi .023
-  #define DEFAULT_bedKd 305.4
+  #define DEFAULT_BED_KP 10.00
+  #define DEFAULT_BED_KI .023
+  #define DEFAULT_BED_KD 305.4

  // FIND YOUR OWN: "M303 E-1 C8 S90" to run autotune on the bed at 90 degreesC for 8 cycles.
 #else
@@ -821,9 +821,9 @@
  // Lasko "MyHeat Personal Heater" (200w) modified with a Fotek SSR-10DA to control only the heating element
  // and placed inside the small Creality printer enclosure tent.
  //
-  #define DEFAULT_chamberKp  37.04
-  #define DEFAULT_chamberKi   1.40
-  #define DEFAULT_chamberKd 655.17
+  #define DEFAULT_CHAMBER_KP  37.04
+  #define DEFAULT_CHAMBER_KI   1.40
+  #define DEFAULT_CHAMBER_KD 655.17
  // M309 P37.04 I1.04 D655.17

  // FIND YOUR OWN: "M303 E-2 C8 S50" to run autotune on the chamber at 50 degreesC for 8 cycles.
--- a/Marlin/Configuration_adv.h
+++ b/Marlin/Configuration_adv.h
@@ -30,7 +30,7 @@
 *
 * Basic settings can be found in Configuration.h
 */
-#define CONFIGURATION_ADV_H_VERSION 02010205
+#define CONFIGURATION_ADV_H_VERSION 02010206

 // @section develop

@@ -375,14 +375,14 @@
  // A well-chosen Kc value should add just enough power to melt the increased material volume.
  //#define PID_EXTRUSION_SCALING
  #if ENABLED(PID_EXTRUSION_SCALING)
-    #define DEFAULT_Kc (100) // heating power = Kc * e_speed
+    #define DEFAULT_KC (100) // heating power = Kc * e_speed
    #define LPQ_MAX_LEN 50
  #endif

  /**
   * Add an additional term to the heater power, proportional to the fan speed.
   * A well-chosen Kf value should add just enough power to compensate for power-loss from the cooling fan.
-   * You can either just add a constant compensation with the DEFAULT_Kf value
+   * You can either just add a constant compensation with the DEFAULT_KF value
   * or follow the instruction below to get speed-dependent compensation.
   *
   * Constant compensation (use only with fan speeds of 0% and 100%)
@@ -413,18 +413,18 @@
    #if ENABLED(PID_FAN_SCALING_ALTERNATIVE_DEFINITION)
      // The alternative definition is used for an easier configuration.
      // Just figure out Kf at full speed (255) and PID_FAN_SCALING_MIN_SPEED.
-      // DEFAULT_Kf and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.
+      // DEFAULT_KF and PID_FAN_SCALING_LIN_FACTOR are calculated accordingly.

-      #define PID_FAN_SCALING_AT_FULL_SPEED 13.0        //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_Kf
-      #define PID_FAN_SCALING_AT_MIN_SPEED   6.0        //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_Kf
+      #define PID_FAN_SCALING_AT_FULL_SPEED 13.0        //=PID_FAN_SCALING_LIN_FACTOR*255+DEFAULT_KF
+      #define PID_FAN_SCALING_AT_MIN_SPEED   6.0        //=PID_FAN_SCALING_LIN_FACTOR*PID_FAN_SCALING_MIN_SPEED+DEFAULT_KF
      #define PID_FAN_SCALING_MIN_SPEED     10.0        // Minimum fan speed at which to enable PID_FAN_SCALING

-      #define DEFAULT_Kf (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
-      #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_Kf)/255.0
+      #define DEFAULT_KF (255.0*PID_FAN_SCALING_AT_MIN_SPEED-PID_FAN_SCALING_AT_FULL_SPEED*PID_FAN_SCALING_MIN_SPEED)/(255.0-PID_FAN_SCALING_MIN_SPEED)
+      #define PID_FAN_SCALING_LIN_FACTOR (PID_FAN_SCALING_AT_FULL_SPEED-DEFAULT_KF)/255.0

    #else
      #define PID_FAN_SCALING_LIN_FACTOR (0)             // Power-loss due to cooling = Kf * (fan_speed)
-      #define DEFAULT_Kf 10                              // A constant value added to the PID-tuner
+      #define DEFAULT_KF 10                              // A constant value added to the PID-tuner
      #define PID_FAN_SCALING_MIN_SPEED 10               // Minimum fan speed at which to enable PID_FAN_SCALING
    #endif
  #endif
--- a/Marlin/Version.h
+++ b/Marlin/Version.h
@@ -28,7 +28,7 @@
 /**
 * Marlin release version identifier
 */
-//#define SHORT_BUILD_VERSION "2.1.2.5"
+//#define SHORT_BUILD_VERSION "2.1.2.7"

 /**
 * Verbose version identifier which should contain a reference to the location
@@ -41,7 +41,7 @@
 * here we define this default string as the date where the latest release
 * version was tagged.
 */
-//#define STRING_DISTRIBUTION_DATE "2024-11-18"
+//#define STRING_DISTRIBUTION_DATE "2026-01-22"

 /**
 * The protocol for communication to the host. Protocol indicates communication
--- a/Marlin/src/HAL/AVR/timers.h
+++ b/Marlin/src/HAL/AVR/timers.h
@@ -111,8 +111,8 @@ FORCE_INLINE void HAL_timer_start(const uint8_t timer_num, const uint32_t) {
 * (otherwise, characters will be lost due to UART overflow).
 * Then: Stepper, Endstops, Temperature, and -finally- all others.
 */
-#define HAL_timer_isr_prologue(T) NOOP
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_prologue(const uint8_t) {}
+inline void HAL_timer_isr_epilogue(const uint8_t) {}

 #ifndef HAL_STEP_TIMER_ISR

--- a/Marlin/src/HAL/DUE/timers.h
+++ b/Marlin/src/HAL/DUE/timers.h
@@ -127,4 +127,4 @@ FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) {
  pConfig->pTimerRegs->TC_CHANNEL[pConfig->channel].TC_SR;
 }

-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/ESP32/timers.h
+++ b/Marlin/src/HAL/ESP32/timers.h
@@ -136,5 +136,5 @@ void HAL_timer_enable_interrupt(const uint8_t timer_num);
 void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

-#define HAL_timer_isr_prologue(T) NOOP
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_prologue(const uint8_t) {}
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/HC32/pinsDebug.h
+++ b/Marlin/src/HAL/HC32/pinsDebug.h
@@ -1,180 +0,0 @@
-/**
- * Marlin 3D Printer Firmware
- * Copyright (c) 2023 MarlinFirmware [https://github.com/MarlinFirmware/Marlin]
- *
- * This program is free software: you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation, either version 3 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program.  If not, see <https://www.gnu.org/licenses/>.
- *
- */
-#pragma once
-
-/**
- * Pins Debugging for HC32
- *
- *   - NUMBER_PINS_TOTAL
- *   - MULTI_NAME_PAD
- *   - getPinByIndex(index)
- *   - printPinNameByIndex(index)
- *   - getPinIsDigitalByIndex(index)
- *   - digitalPinToAnalogIndex(pin)
- *   - getValidPinMode(pin)
- *   - isValidPin(pin)
- *   - isAnalogPin(pin)
- *   - digitalRead_mod(pin)
- *   - pwm_status(pin)
- *   - printPinPWM(pin)
- *   - printPinPort(pin)
- *   - printPinNumber(pin)
- *   - printPinAnalog(pin)
- */
-
-#include "../../inc/MarlinConfig.h"
-#include "fastio.h"
-#include <drivers/timera/timera_pwm.h>
-
-#ifndef BOARD_NR_GPIO_PINS
-  #error "Expected BOARD_NR_GPIO_PINS not found."
-#endif
-
-#define NUM_DIGITAL_PINS BOARD_NR_GPIO_PINS
-#define NUMBER_PINS_TOTAL BOARD_NR_GPIO_PINS
-#define isValidPin(P) IS_GPIO_PIN(P)
-
-// Note: pin_array is defined in `Marlin/src/pins/pinsDebug.h`, and since this file is included
-// after it, it is available in this file as well.
-#define getPinByIndex(x) pin_t(pin_array[x].pin)
-#define digitalRead_mod(P) extDigitalRead(P)
-
-#define printPinNumber(P) do{ sprintf_P(buffer, PSTR("%3hd "), int16_t(P)); SERIAL_ECHO(buffer); }while(0)
-#define printPinAnalog(P) do{ sprintf_P(buffer, PSTR(" (A%2d)  "), digitalPinToAnalogIndex(P)); SERIAL_ECHO(buffer); }while(0)
-
-#define printPinNameByIndex(x) do{ sprintf_P(buffer, PSTR("%-" STRINGIFY(MAX_NAME_LENGTH) "s"), pin_array[x].name); SERIAL_ECHO(buffer); }while(0)
-
-#define MULTI_NAME_PAD 21 // Space needed to be pretty if not first name assigned to a pin
-
-//
-// Pins that will cause a hang / reset / disconnect in M43 Toggle and Watch utils
-//
-#ifndef M43_NEVER_TOUCH
-  // Don't touch any of the following pins:
-  // - Host serial pins, and
-  // - Pins that could be connected to oscillators (see datasheet, Table 2.1):
-  //   - XTAL = PH0, PH1
-  //   - XTAL32 = PC14, PC15
-  #define IS_HOST_USART_PIN(Q) (Q == BOARD_USART2_TX_PIN || Q == BOARD_USART2_RX_PIN)
-  #define IS_OSC_PIN(Q) (Q == PH0 || Q == PH1 || Q == PC14 || Q == PC15)
-
-  #define M43_NEVER_TOUCH(Q) (IS_HOST_USART_PIN(Q) || IS_OSC_PIN(Q))
-#endif
-
-int8_t digitalPinToAnalogIndex(const pin_t pin) {
-  if (!isValidPin(pin)) return -1;
-  const int8_t adc_channel = int8_t(PIN_MAP[pin].adc_info.channel);
-  return pin_t(adc_channel);
-}
-
-bool isAnalogPin(pin_t pin) {
-  if (!isValidPin(pin)) return false;
-
-  if (PIN_MAP[pin].adc_info.channel != ADC_PIN_INVALID)
-    return _GET_MODE(pin) == INPUT_ANALOG && !M43_NEVER_TOUCH(pin);
-
-  return false;
-}
-
-bool getValidPinMode(const pin_t pin) {
-  return isValidPin(pin) && !IS_INPUT(pin);
-}
-
-bool getPinIsDigitalByIndex(const int16_t index) {
-  const pin_t pin = getPinByIndex(index);
-  return (!isAnalogPin(pin));
-}
-
-/**
- * @brief print pin PWM status
- * @return true if pin is currently a PWM pin, false otherwise
- */
-bool pwm_status(const pin_t pin) {
-  // Get timer assignment for pin
-  timera_config_t *unit;
-  en_timera_channel_t channel;
-  en_port_func_t port_function;
-  if (!timera_get_assignment(pin, unit, channel, port_function) || unit == nullptr) {
-    // No pwm pin or no unit assigned
-    return false;
-  }
-
-  // A pin that is PWM output is:
-  // - Assigned to a timerA unit (tested above)
-  // - Unit is initialized
-  // - Channel is active
-  // - PinMode is OUTPUT_PWM
-  return timera_is_unit_initialized(unit) && timera_is_channel_active(unit, channel) && getPinMode(pin) == OUTPUT_PWM;
-}
-
-void printPinPWM(const pin_t pin) {
-  // Get timer assignment for pin
-  timera_config_t *unit;
-  en_timera_channel_t channel;
-  en_port_func_t port_function;
-  if (!timera_get_assignment(pin, unit, channel, port_function) || unit == nullptr)
-    return; // No pwm pin or no unit assigned
-
-  // Print timer assignment of pin, eg. "TimerA1Ch2 Func4"
-  SERIAL_ECHOPGM("TimerA", TIMERA_REG_TO_X(unit->peripheral.register_base),
-                 "Ch", TIMERA_CHANNEL_TO_X(channel),
-                 " Func", int(port_function));
-  SERIAL_ECHO_SP(3); // 3 spaces
-
-  // Print timer unit state, eg. "1/16 PERAR=1234" OR "N/A"
-  if (timera_is_unit_initialized(unit)) {
-    // Unit initialized, print
-    // - Timer clock divider
-    // - Timer period value (PERAR)
-    const uint8_t clock_divider = timera_clk_div_to_n(unit->state.base_init->enClkDiv);
-    const uint16_t period = TIMERA_GetPeriodValue(unit->peripheral.register_base);
-    SERIAL_ECHOPGM("1/", clock_divider, " PERAR=", period);
-  }
-  else {
-    // Unit not initialized
-    SERIAL_ECHOPGM("N/A");
-    return;
-  }
-
-  SERIAL_ECHO_SP(3); // 3 spaces
-
-  // Print timer channel state, e.g. "CMPAR=1234" OR "N/A"
-  if (timera_is_channel_active(unit, channel)) {
-    // Channel active, print
-    // - Channel compare value
-    const uint16_t compare = TIMERA_GetCompareValue(unit->peripheral.register_base, channel);
-    SERIAL_ECHOPGM("CMPAR=", compare);
-  }
-  else {
-    // Channel inactive
-    SERIAL_ECHOPGM("N/A");
-  }
-}
-
-void printPinPort(pin_t pin) {
-  const char port = 'A' + char(pin >> 4); // Pin div 16
-  const int16_t gbit = PIN_MAP[pin].bit_pos;
-  char buffer[8];
-  sprintf_P(buffer, PSTR("P%c%hd "), port, gbit);
-  if (gbit < 10) {
-    SERIAL_CHAR(' ');
-  }
-
-  SERIAL_ECHO(buffer);
-}
--- a/Marlin/src/HAL/LINUX/timers.h
+++ b/Marlin/src/HAL/LINUX/timers.h
@@ -93,5 +93,5 @@ void HAL_timer_enable_interrupt(const uint8_t timer_num);
 void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

-#define HAL_timer_isr_prologue(T) NOOP
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_prologue(const uint8_t) {}
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/LPC1768/timers.h
+++ b/Marlin/src/HAL/LPC1768/timers.h
@@ -171,4 +171,4 @@ FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) {
  }
 }

-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/NATIVE_SIM/timers.h
+++ b/Marlin/src/HAL/NATIVE_SIM/timers.h
@@ -88,5 +88,5 @@ void HAL_timer_enable_interrupt(const uint8_t timer_num);
 void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

-#define HAL_timer_isr_prologue(T) NOOP
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_prologue(const uint8_t) {}
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/SAMD21/timers.h
+++ b/Marlin/src/HAL/SAMD21/timers.h
@@ -157,4 +157,4 @@ FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) {
  }
 }

-#define HAL_timer_isr_epilogue(timer_num)
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/SAMD51/timers.h
+++ b/Marlin/src/HAL/SAMD51/timers.h
@@ -145,4 +145,4 @@ FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) {
  }
 }

-#define HAL_timer_isr_epilogue(timer_num)
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/STM32/MarlinSPI.cpp
+++ b/Marlin/src/HAL/STM32/MarlinSPI.cpp
@@ -39,12 +39,16 @@ static void spi_init(spi_t *obj, uint32_t speed, spi_mode_e mode, uint8_t msb, u

 void MarlinSPI::setClockDivider(uint8_t _div) {
  _speed = spi_getClkFreq(&_spi);// / _div;
-  _clockDivider = _div;
+  if (_clockDivider != _div) {
+    _clockDivider = _div;
+    _mustInit = true;
+  }
 }

 void MarlinSPI::begin(void) {
-  //TODO: only call spi_init if any parameter changed!!
+  if (!_mustInit) return;
  spi_init(&_spi, _speed, _dataMode, _bitOrder, _dataSize);
+  _mustInit = false;
 }

 void MarlinSPI::setupDma(SPI_HandleTypeDef &_spiHandle, DMA_HandleTypeDef &_dmaHandle, uint32_t direction, bool minc) {
--- a/Marlin/src/HAL/STM32/MarlinSPI.h
+++ b/Marlin/src/HAL/STM32/MarlinSPI.h
@@ -76,15 +76,23 @@ public:
  /* These methods are deprecated and kept for compatibility.
   * Use SPISettings with SPI.beginTransaction() to configure SPI parameters.
   */
-  void setBitOrder(BitOrder _order) { _bitOrder = _order; }
+  void setBitOrder(BitOrder order) {
+    if (_bitOrder == order) return;
+    _bitOrder = order;
+    _mustInit = true;
+  }

-  void setDataMode(uint8_t _mode) {
-    switch (_mode) {
+  void setDataMode(uint8_t mode) {
+    auto previous_mode = _dataMode;
+    switch (mode) {
      case SPI_MODE0: _dataMode = SPI_MODE_0; break;
      case SPI_MODE1: _dataMode = SPI_MODE_1; break;
      case SPI_MODE2: _dataMode = SPI_MODE_2; break;
      case SPI_MODE3: _dataMode = SPI_MODE_3; break;
+      default: return;
    }
+    if (previous_mode != _dataMode)
+      _mustInit = true;
  }

  void setClockDivider(uint8_t _div);
@@ -104,4 +112,5 @@ private:
  pin_t _misoPin;
  pin_t _sckPin;
  pin_t _ssPin;
+  bool _mustInit = true;
 };
--- a/Marlin/src/HAL/STM32/timers.h
+++ b/Marlin/src/HAL/STM32/timers.h
@@ -116,5 +116,5 @@ FORCE_INLINE static void HAL_timer_set_compare(const uint8_t timer_num, const ha
  }
 }

-#define HAL_timer_isr_prologue(T) NOOP
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_prologue(const uint8_t) {}
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/STM32F1/build_flags.py
+++ b/Marlin/src/HAL/STM32F1/build_flags.py
@@ -1,56 +1,62 @@
+#!/usr/bin/env python
+#
+# STM32F1/build_flags.py
+# Add build_flags for the base STM32F1_maple environment (stm32f1-maple.ini)
+#
 from __future__ import print_function
 import sys

-#dynamic build flags for generic compile options
+# Dynamic build flags for generic compile options
 if __name__ == "__main__":
-  args = " ".join([ "-std=gnu++14",
-                    "-Os",
-                    "-mcpu=cortex-m3",
-                    "-mthumb",

-                    "-fsigned-char",
-                    "-fno-move-loop-invariants",
-                    "-fno-strict-aliasing",
-                    "-fsingle-precision-constant",
-
-                    "--specs=nano.specs",
-                    "--specs=nosys.specs",
-
-                    "-IMarlin/src/HAL/STM32F1",
-
-                    "-MMD",
-                    "-MP",
-                    "-DTARGET_STM32F1"
-                  ])
-
-  for i in range(1, len(sys.argv)):
-    args += " " + sys.argv[i]
-
-  print(args)
-
-# extra script for linker options
-else:
-  import pioutil
-  if pioutil.is_pio_build():
-    from SCons.Script import DefaultEnvironment
-    env = DefaultEnvironment()
-    env.Append(
-      ARFLAGS=["rcs"],
-
-      ASFLAGS=["-x", "assembler-with-cpp"],
-
-      CXXFLAGS=[
-        "-fabi-version=0",
-        "-fno-use-cxa-atexit",
-        "-fno-threadsafe-statics"
-      ],
-      LINKFLAGS=[
+    # Print these plus the given args when running directly on the command-line
+    args = [
+        "-std=gnu++14",
        "-Os",
        "-mcpu=cortex-m3",
-        "-ffreestanding",
        "-mthumb",
+
+        "-fsigned-char",
+        "-fno-move-loop-invariants",
+        "-fno-strict-aliasing",
+
        "--specs=nano.specs",
        "--specs=nosys.specs",
-        "-u_printf_float",
-      ],
-    )
+
+        "-MMD", "-MP",
+
+        "-IMarlin/src/HAL/STM32F1",
+
+        "-DTARGET_STM32F1",
+        "-DARDUINO_ARCH_STM32",
+        "-DPLATFORM_M997_SUPPORT"
+    ] + sys.argv[1:]
+
+    print(" ".join(args))
+
+else:
+
+    # Extra script for stm32f1-maple.ini build_flags
+
+    import pioutil
+    if pioutil.is_pio_build():
+        pioutil.env.Append(
+            ARFLAGS=["rcs"],
+
+            ASFLAGS=["-x", "assembler-with-cpp"],
+
+            CXXFLAGS=[
+                "-fabi-version=0",
+                "-fno-use-cxa-atexit",
+                "-fno-threadsafe-statics"
+            ],
+            LINKFLAGS=[
+                "-Os",
+                "-mcpu=cortex-m3",
+                "-ffreestanding",
+                "-mthumb",
+                "--specs=nano.specs",
+                "--specs=nosys.specs",
+                "-u_printf_float",
+            ],
+        )
--- a/Marlin/src/HAL/STM32F1/timers.h
+++ b/Marlin/src/HAL/STM32F1/timers.h
@@ -188,7 +188,7 @@ FORCE_INLINE static void HAL_timer_isr_prologue(const uint8_t timer_num) {
  }
 }

-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}

 // No command is available in framework to turn off ARPE bit, which is turned on by default in libmaple.
 // Needed here to reset ARPE=0 for stepper timer
--- a/Marlin/src/HAL/TEENSY31_32/timers.h
+++ b/Marlin/src/HAL/TEENSY31_32/timers.h
@@ -74,10 +74,10 @@ typedef uint32_t hal_timer_t;
 #define DISABLE_TEMPERATURE_INTERRUPT() HAL_timer_disable_interrupt(MF_TIMER_TEMP)

 #ifndef HAL_STEP_TIMER_ISR
-  #define HAL_STEP_TIMER_ISR() extern "C" void ftm0_isr() //void TC3_Handler()
+  #define HAL_STEP_TIMER_ISR() extern "C" void ftm0_isr()
 #endif
 #ifndef HAL_TEMP_TIMER_ISR
-  #define HAL_TEMP_TIMER_ISR() extern "C" void ftm1_isr() //void TC4_Handler()
+  #define HAL_TEMP_TIMER_ISR() extern "C" void ftm1_isr()
 #endif

 void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency);
@@ -110,4 +110,4 @@ void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

 void HAL_timer_isr_prologue(const uint8_t timer_num);
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/TEENSY35_36/timers.h
+++ b/Marlin/src/HAL/TEENSY35_36/timers.h
@@ -110,4 +110,4 @@ void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

 void HAL_timer_isr_prologue(const uint8_t timer_num);
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/HAL/TEENSY40_41/timers.cpp
+++ b/Marlin/src/HAL/TEENSY40_41/timers.cpp
@@ -30,41 +30,82 @@

 void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency) {
  switch (timer_num) {
+
+    //
+    // Step Timer – GPT1 - Compare Interrupt OCR1 - Reset Mode
+    //
    case MF_TIMER_STEP:
-      CCM_CSCMR1 &= ~CCM_CSCMR1_PERCLK_CLK_SEL; // turn off 24mhz mode
+      // 24MHz mode off – Use peripheral clock (150MHz)
+      CCM_CSCMR1 &= ~CCM_CSCMR1_PERCLK_CLK_SEL;
+      // Enable GPT1 clock gating
      CCM_CCGR1 |= CCM_CCGR1_GPT1_BUS(CCM_CCGR_ON);

-      GPT1_CR = 0;                   // disable timer
-      GPT1_SR = 0x3F;                // clear all prior status
-      GPT1_PR = GPT1_TIMER_PRESCALE - 1;
-      GPT1_CR |= GPT_CR_CLKSRC(1);   //clock selection #1 (peripheral clock = 150 MHz)
-      GPT1_CR |= GPT_CR_ENMOD;       //reset count to zero before enabling
-      GPT1_CR |= GPT_CR_OM1(1);      // toggle mode
-      GPT1_OCR1 = (GPT1_TIMER_RATE / frequency) -1; // Initial compare value
-      GPT1_IR = GPT_IR_OF1IE;        // Compare3 value
-      GPT1_CR |= GPT_CR_EN;          //enable GPT2 counting at 150 MHz
+      // Disable timer, clear all status bits
+      GPT1_CR = 0;                      // Disable timer
+      GPT1_SR = 0x3F;                   // Clear all prior status

-      OUT_WRITE(15, HIGH);
+      // Prescaler = 2 => 75MHz counting clock
+      GPT1_PR = GPT1_TIMER_PRESCALE - 1;
+
+      GPT1_CR = GPT_CR_CLKSRC(1)        // Clock selection #1 (peripheral clock = 150 MHz)
+              | GPT_CR_ENMOD            // Reset count to zero before enabling
+              | GPT_CR_OM2(TERN(MARLIN_DEV_MODE, 1, 0)); // 0 = edge compare, 1 = toggle
+
+      // Compare value – the number of clocks between edges
+      GPT1_OCR1 = (GPT1_TIMER_RATE / frequency) - 1;
+
+      // Enable compare‑event interrupt
+      GPT1_IR = GPT_IR_OF1IE;           // OF1 interrupt enabled
+
+      // Pull Pin 15 HIGH (logic‑high is the “idle” state)
+      TERN_(MARLIN_DEV_MODE, OUT_WRITE(15, HIGH));
+
+      // Attach and enable Stepper IRQ
+      // Note: UART priority is 16
      attachInterruptVector(IRQ_GPT1, &stepTC_Handler);
-      NVIC_SET_PRIORITY(IRQ_GPT1, 16);
+      NVIC_SET_PRIORITY(IRQ_GPT1, 16);  // Priority 16 (higher than Temp Timer)
+
+      // Start GPT1 counting at 150 MHz
+      GPT1_CR |= GPT_CR_EN;
+
      break;
+
+    //
+    // Temperature Timer – GPT2 - Compare Interrupt OCR1 - Reset Mode
+    //
    case MF_TIMER_TEMP:
-      CCM_CSCMR1 &= ~CCM_CSCMR1_PERCLK_CLK_SEL; // turn off 24mhz mode
+      // 24MHz mode off – Use peripheral clock (150MHz)
+      CCM_CSCMR1 &= ~CCM_CSCMR1_PERCLK_CLK_SEL;
+      // Enable GPT2 clock gating
      CCM_CCGR0 |= CCM_CCGR0_GPT2_BUS(CCM_CCGR_ON);

-      GPT2_CR = 0;                   // disable timer
-      GPT2_SR = 0x3F;                // clear all prior status
-      GPT2_PR = GPT2_TIMER_PRESCALE - 1;
-      GPT2_CR |= GPT_CR_CLKSRC(1);   //clock selection #1 (peripheral clock = 150 MHz)
-      GPT2_CR |= GPT_CR_ENMOD;       //reset count to zero before enabling
-      GPT2_CR |= GPT_CR_OM1(1);      // toggle mode
-      GPT2_OCR1 = (GPT2_TIMER_RATE / frequency) -1; // Initial compare value
-      GPT2_IR = GPT_IR_OF1IE;        // Compare3 value
-      GPT2_CR |= GPT_CR_EN;          //enable GPT2 counting at 150 MHz
+      // Disable timer, clear all status bits
+      GPT2_CR = 0;                      // Disable timer
+      GPT2_SR = 0x3F;                   // Clear all prior status

-      OUT_WRITE(14, HIGH);
+      // Prescaler = 10 => 15MHz counting clock
+      GPT2_PR = GPT2_TIMER_PRESCALE - 1;
+
+      GPT2_CR = GPT_CR_CLKSRC(1)        // Clock selection #1 (peripheral clock = 150 MHz)
+              | GPT_CR_ENMOD            // and reset count to zero before enabling
+              | GPT_CR_OM2(TERN(MARLIN_DEV_MODE, 1, 0)); // 0 = edge compare, 1 = toggle
+
+      // Compare value – the number of clocks between edges
+      GPT2_OCR1 = (GPT2_TIMER_RATE / frequency) - 1;
+
+      // Enable compare‑event interrupt
+      GPT2_IR = GPT_IR_OF1IE;           // OF1 interrupt enabled
+
+      // Pull Pin 14 HIGH (logic‑high is the “idle” state)
+      TERN_(MARLIN_DEV_MODE, OUT_WRITE(14, HIGH));
+
+      // Attach Temperature ISR
      attachInterruptVector(IRQ_GPT2, &tempTC_Handler);
-      NVIC_SET_PRIORITY(IRQ_GPT2, 32);
+      NVIC_SET_PRIORITY(IRQ_GPT2, 32);  // Priority 32 (lower than Step Timer)
+
+      // Start GPT2 counting at 150 MHz
+      GPT2_CR |= GPT_CR_EN;
+
      break;
  }
 }
@@ -82,6 +123,7 @@ void HAL_timer_disable_interrupt(const uint8_t timer_num) {
    case MF_TIMER_TEMP: NVIC_DISABLE_IRQ(IRQ_GPT2); break;
  }

+  // Ensure the CPU actually stops servicing the IRQ
  // We NEED memory barriers to ensure Interrupts are actually disabled!
  // ( https://dzone.com/articles/nvic-disabling-interrupts-on-arm-cortex-m-and-the )
  asm volatile("dsb");
@@ -97,8 +139,8 @@ bool HAL_timer_interrupt_enabled(const uint8_t timer_num) {

 void HAL_timer_isr_prologue(const uint8_t timer_num) {
  switch (timer_num) {
-    case MF_TIMER_STEP: GPT1_SR = GPT_IR_OF1IE; break; // clear OF3 bit
-    case MF_TIMER_TEMP: GPT2_SR = GPT_IR_OF1IE; break; // clear OF3 bit
+    case MF_TIMER_STEP: GPT1_SR = GPT_IR_OF1IE; break;   // clear OF1
+    case MF_TIMER_TEMP: GPT2_SR = GPT_IR_OF1IE; break;
  }
  asm volatile("dsb");
 }
--- a/Marlin/src/HAL/TEENSY40_41/timers.h
+++ b/Marlin/src/HAL/TEENSY40_41/timers.h
@@ -60,7 +60,7 @@ typedef uint32_t hal_timer_t;
 #define HAL_TIMER_RATE         GPT1_TIMER_RATE
 #define STEPPER_TIMER_RATE     HAL_TIMER_RATE
 #define STEPPER_TIMER_TICKS_PER_US ((STEPPER_TIMER_RATE) / 1000000)
-#define STEPPER_TIMER_PRESCALE ((GPT_TIMER_RATE / 1000000) / STEPPER_TIMER_TICKS_PER_US)
+#define STEPPER_TIMER_PRESCALE (GPT_TIMER_RATE / STEPPER_TIMER_RATE)

 #define PULSE_TIMER_RATE       STEPPER_TIMER_RATE   // frequency of pulse timer
 #define PULSE_TIMER_PRESCALE   STEPPER_TIMER_PRESCALE
@@ -89,8 +89,16 @@ void HAL_timer_start(const uint8_t timer_num, const uint32_t frequency);

 FORCE_INLINE static void HAL_timer_set_compare(const uint8_t timer_num, const hal_timer_t compare) {
  switch (timer_num) {
-    case MF_TIMER_STEP: GPT1_OCR1 = compare - 1; break;
-    case MF_TIMER_TEMP: GPT2_OCR1 = compare - 1; break;
+    case MF_TIMER_STEP:
+      GPT1_CR |= GPT_CR_FRR;    // Free Run Mode (setting OCRx preserves CNT)
+      GPT1_OCR1 = compare - 1;
+      GPT1_CR &= ~GPT_CR_FRR;   // Reset Mode (CNT resets on trigger)
+      break;
+    case MF_TIMER_TEMP:
+      GPT2_CR |= GPT_CR_FRR;    // Free Run Mode (setting OCRx preserves CNT)
+      GPT2_OCR1 = compare - 1;
+      GPT2_CR &= ~GPT_CR_FRR;   // Reset Mode (CNT resets on trigger)
+      break;
  }
 }

@@ -115,5 +123,4 @@ void HAL_timer_disable_interrupt(const uint8_t timer_num);
 bool HAL_timer_interrupt_enabled(const uint8_t timer_num);

 void HAL_timer_isr_prologue(const uint8_t timer_num);
-//void HAL_timer_isr_epilogue(const uint8_t timer_num) {}
-#define HAL_timer_isr_epilogue(T) NOOP
+inline void HAL_timer_isr_epilogue(const uint8_t) {}
--- a/Marlin/src/core/macros.h
+++ b/Marlin/src/core/macros.h
@@ -802,3 +802,5 @@
 #define _HAS_E_TEMP(N) || TEMP_SENSOR(N)
 #define HAS_E_TEMP_SENSOR (0 REPEAT(EXTRUDERS, _HAS_E_TEMP))
 #define TEMP_SENSOR_IS_MAX_TC(T) (TEMP_SENSOR(T) == -5 || TEMP_SENSOR(T) == -3 || TEMP_SENSOR(T) == -2)
+
+#define DGUS_UI_IS(...) 0 // Dummy macro needed for future preflight checking
--- a/Marlin/src/inc/Changes.h
+++ b/Marlin/src/inc/Changes.h
@@ -621,6 +621,18 @@
  #error "BTT_MINI_12864_V1 is now BTT_MINI_12864."
 #elif defined(SDIO_SUPPORT)
  #error "SDIO_SUPPORT is now ONBOARD_SDIO."
+#elif defined(DEFAULT_Kp_LIST) || defined(DEFAULT_Ki_LIST) || defined(DEFAULT_Kd_LIST)
+  #error "DEFAULT_Kp_LIST, DEFAULT_Ki_LIST, DEFAULT_Kd_LIST are now (uppercase) DEFAULT_KP_LIST, DEFAULT_KI_LIST, DEFAULT_KD_LIST."
+#elif defined(DEFAULT_Kp) || defined(DEFAULT_Ki) || defined(DEFAULT_Kd)
+  #error "DEFAULT_Kp, DEFAULT_Ki, DEFAULT_Kd are now (uppercase) DEFAULT_KP, DEFAULT_KI, DEFAULT_KD."
+#elif defined(DEFAULT_bedKp) || defined(DEFAULT_bedKi) || defined(DEFAULT_bedKd)
+  #error "DEFAULT_bedKp, DEFAULT_bedKi, DEFAULT_bedKd are now DEFAULT_BED_KP, DEFAULT_BED_KI, DEFAULT_BED_KD."
+#elif defined(DEFAULT_chamberKp) || defined(DEFAULT_chamberKi) || defined(DEFAULT_chamberKd)
+  #error "DEFAULT_chamberKp, DEFAULT_chamberKi, DEFAULT_chamberKd are now DEFAULT_CHAMBER_KP, DEFAULT_CHAMBER_KI, DEFAULT_CHAMBER_KD."
+#elif defined(DEFAULT_Kc)
+  #error "DEFAULT_Kc is now (uppercase) DEFAULT_KC."
+#elif defined(DEFAULT_Kf)
+  #error "DEFAULT_Kf is now (uppercase) DEFAULT_KF."
 #endif

 // L64xx stepper drivers have been removed
--- a/Marlin/src/inc/Conditionals_LCD.h
+++ b/Marlin/src/inc/Conditionals_LCD.h
@@ -1013,6 +1013,7 @@
 #endif
 #if ANY(HAS_DWIN_E3V2_BASIC, DWIN_CREALITY_LCD_JYERSUI)
  #define HAS_DWIN_E3V2 1
+  #undef LCD_BED_LEVELING // allow for MESH_EDIT_MENU
 #endif

 // E3V2 extras
--- a/Marlin/src/inc/SanityCheck.h
+++ b/Marlin/src/inc/SanityCheck.h
@@ -1528,7 +1528,7 @@ static_assert(COUNT(arm) == LOGICAL_AXES, "AXIS_RELATIVE_MODES must contain " _L
 * LCD_BED_LEVELING requirements
 */
 #if ENABLED(LCD_BED_LEVELING)
-  #if !HAS_MARLINUI_MENU
+  #if NONE(HAS_MARLINUI_MENU, DWIN_LCD_PROUI)
    #error "LCD_BED_LEVELING is not supported by the selected LCD controller."
  #elif !(ENABLED(MESH_BED_LEVELING) || HAS_ABL_NOT_UBL)
    #error "LCD_BED_LEVELING requires MESH_BED_LEVELING or AUTO_BED_LEVELING."
--- a/Marlin/src/inc/Version.h
+++ b/Marlin/src/inc/Version.h
@@ -25,7 +25,7 @@
 * Release version. Leave the Marlin version or apply a custom scheme.
 */
 #ifndef SHORT_BUILD_VERSION
-  #define SHORT_BUILD_VERSION "2.1.2.5"
+  #define SHORT_BUILD_VERSION "2.1.2.7"
 #endif

 /**
@@ -42,7 +42,7 @@
 * version was tagged.
 */
 #ifndef STRING_DISTRIBUTION_DATE
-  #define STRING_DISTRIBUTION_DATE "2024-11-18"
+  #define STRING_DISTRIBUTION_DATE "2026-01-22"
 #endif

 /**
@@ -52,7 +52,7 @@
 * to alert users to major changes.
 */

-#define MARLIN_HEX_VERSION 02010205
+#define MARLIN_HEX_VERSION 02010206
 #ifndef REQUIRED_CONFIGURATION_H_VERSION
  #define REQUIRED_CONFIGURATION_H_VERSION MARLIN_HEX_VERSION
 #endif
--- a/Marlin/src/lcd/dogm/status_screen_DOGM.cpp
+++ b/Marlin/src/lcd/dogm/status_screen_DOGM.cpp
@@ -503,7 +503,9 @@ void MarlinUI::draw_status_screen() {

  const bool show_e_total = TERN0(LCD_SHOW_E_TOTAL, printingIsActive());

-  static u8g_uint_t progress_bar_solid_width = 0;
+  #if HAS_PRINT_PROGRESS
+    static u8g_uint_t progress_bar_solid_width = 0;
+  #endif

  // At the first page, generate new display values
  if (first_page) {
--- a/Marlin/src/lcd/e3v2/proui/dwin_lcd.cpp
+++ b/Marlin/src/lcd/e3v2/proui/dwin_lcd.cpp
@@ -127,7 +127,7 @@ void DWIN_WriteToMem(uint8_t mem, uint16_t addr, uint16_t length, uint8_t *data)
    DWIN_Word(i, addr + indx); // start address of the data block
    ++i;
    for (uint8_t j = 0; j < i; ++j) { LCD_SERIAL.write(DWIN_SendBuf[j]); delayMicroseconds(1); }  // Buf header
-    for (uint16_t j = indx; j <= indx + to_send - 1; j++) LCD_SERIAL.write(*(data + j)); delayMicroseconds(1);  // write block of data
+    for (uint16_t j = indx; j <= indx + to_send - 1; j++) { LCD_SERIAL.write(*(data + j)); delayMicroseconds(1); } // write block of data
    for (uint8_t j = 0; j < 4; ++j) { LCD_SERIAL.write(DWIN_BufTail[j]); delayMicroseconds(1); }
    block++;
    pending -= to_send;
--- a/Marlin/src/lcd/e3v2/proui/menus.cpp
+++ b/Marlin/src/lcd/e3v2/proui/menus.cpp
@@ -128,7 +128,7 @@ void onDrawMenuItem(MenuItemClass* menuitem, int8_t line) {
  if (menuitem->icon) DWINUI::Draw_Icon(menuitem->icon, ICOX, MBASE(line) - 3);
  if (menuitem->frameid)
    DWIN_Frame_AreaCopy(menuitem->frameid, menuitem->frame.left, menuitem->frame.top, menuitem->frame.right, menuitem->frame.bottom, LBLX, MBASE(line));
-  else if (menuitem->caption)
+  else if (menuitem->caption[0])
    DWINUI::Draw_String(LBLX, MBASE(line) - 1, menuitem->caption);
  DWIN_Draw_HLine(HMI_data.SplitLine_Color, 16, MYPOS(line + 1), 240);
 }
--- a/Marlin/src/lcd/marlinui.h
+++ b/Marlin/src/lcd/marlinui.h
@@ -548,7 +548,7 @@ public:
    static FSTR_P get_preheat_label(const uint8_t m);
    static void apply_preheat(const uint8_t m, const uint8_t pmask, const uint8_t e=active_extruder);
    static void preheat_set_fan(const uint8_t m) { TERN_(HAS_FAN, apply_preheat(m, _BV(PT_FAN))); }
-    static void preheat_hotend(const uint8_t m, const uint8_t e=active_extruder) { TERN_(HAS_HOTEND, apply_preheat(m, _BV(PT_HOTEND))); }
+    static void preheat_hotend(const uint8_t m, const uint8_t e=active_extruder) { TERN_(HAS_HOTEND, apply_preheat(m, _BV(PT_HOTEND), e)); }
    static void preheat_hotend_and_fan(const uint8_t m, const uint8_t e=active_extruder) { preheat_hotend(m, e); preheat_set_fan(m); }
    static void preheat_bed(const uint8_t m) { TERN_(HAS_HEATED_BED, apply_preheat(m, _BV(PT_BED))); }
    static void preheat_all(const uint8_t m) { apply_preheat(m, PT_ALL); }
--- a/Marlin/src/lcd/menu/menu_bed_leveling.cpp
+++ b/Marlin/src/lcd/menu/menu_bed_leveling.cpp
@@ -36,11 +36,9 @@
  #include "../../module/probe.h"
 #endif

-#if HAS_GRAPHICAL_TFT
+#if ALL(TOUCH_SCREEN, HAS_GRAPHICAL_TFT)
  #include "../tft/tft.h"
-  #if ENABLED(TOUCH_SCREEN)
-    #include "../tft/touch.h"
-  #endif
+  #include "../tft/touch.h"
 #endif

 #if ANY(PROBE_MANUALLY, MESH_BED_LEVELING)
--- a/Marlin/src/lcd/menu/menu_x_twist.cpp
+++ b/Marlin/src/lcd/menu/menu_x_twist.cpp
@@ -36,6 +36,11 @@
  #define XATC_Y_POSITION ((probe.max_y() - probe.min_y())/2)
 #endif

+#if ALL(TOUCH_SCREEN, HAS_GRAPHICAL_TFT)
+  #include "../tft/tft.h"
+  #include "../tft/touch.h"
+#endif
+
 void _goto_manual_move_z(const_float_t);

 float measured_z, z_offset;
--- a/Marlin/src/module/probe.cpp
+++ b/Marlin/src/module/probe.cpp
@@ -109,6 +109,8 @@ xyz_pos_t Probe::offset; // Initialized by settings.load

 #if HAS_PROBE_XY_OFFSET
  const xy_pos_t &Probe::offset_xy = Probe::offset;
+#else
+  constexpr xy_pos_t Probe::offset_xy;
 #endif

 #if ENABLED(SENSORLESS_PROBING)
--- a/Marlin/src/module/settings.cpp
+++ b/Marlin/src/module/settings.cpp
@@ -3242,47 +3242,47 @@ void MarlinSettings::reset() {

  #if ENABLED(PIDTEMP)
    #if ENABLED(PID_PARAMS_PER_HOTEND)
-      constexpr float defKp[] =
-        #ifdef DEFAULT_Kp_LIST
-          DEFAULT_Kp_LIST
+      constexpr float defKP[] =
+        #ifdef DEFAULT_KP_LIST
+          DEFAULT_KP_LIST
        #else
-          ARRAY_BY_HOTENDS1(DEFAULT_Kp)
+          ARRAY_BY_HOTENDS1(DEFAULT_KP)
        #endif
-      , defKi[] =
-        #ifdef DEFAULT_Ki_LIST
-          DEFAULT_Ki_LIST
+      , defKI[] =
+        #ifdef DEFAULT_KI_LIST
+          DEFAULT_KI_LIST
        #else
-          ARRAY_BY_HOTENDS1(DEFAULT_Ki)
+          ARRAY_BY_HOTENDS1(DEFAULT_KI)
        #endif
-      , defKd[] =
-        #ifdef DEFAULT_Kd_LIST
-          DEFAULT_Kd_LIST
+      , defKD[] =
+        #ifdef DEFAULT_KD_LIST
+          DEFAULT_KD_LIST
        #else
-          ARRAY_BY_HOTENDS1(DEFAULT_Kd)
+          ARRAY_BY_HOTENDS1(DEFAULT_KD)
        #endif
      ;
-      static_assert(WITHIN(COUNT(defKp), 1, HOTENDS), "DEFAULT_Kp_LIST must have between 1 and HOTENDS items.");
-      static_assert(WITHIN(COUNT(defKi), 1, HOTENDS), "DEFAULT_Ki_LIST must have between 1 and HOTENDS items.");
-      static_assert(WITHIN(COUNT(defKd), 1, HOTENDS), "DEFAULT_Kd_LIST must have between 1 and HOTENDS items.");
+      static_assert(WITHIN(COUNT(defKP), 1, HOTENDS), "DEFAULT_KP_LIST must have between 1 and HOTENDS items.");
+      static_assert(WITHIN(COUNT(defKI), 1, HOTENDS), "DEFAULT_KI_LIST must have between 1 and HOTENDS items.");
+      static_assert(WITHIN(COUNT(defKD), 1, HOTENDS), "DEFAULT_KD_LIST must have between 1 and HOTENDS items.");
      #if ENABLED(PID_EXTRUSION_SCALING)
-        constexpr float defKc[] =
-          #ifdef DEFAULT_Kc_LIST
-            DEFAULT_Kc_LIST
+        constexpr float defKC[] =
+          #ifdef DEFAULT_KC_LIST
+            DEFAULT_KC_LIST
          #else
-            ARRAY_BY_HOTENDS1(DEFAULT_Kc)
+            ARRAY_BY_HOTENDS1(DEFAULT_KC)
          #endif
        ;
-        static_assert(WITHIN(COUNT(defKc), 1, HOTENDS), "DEFAULT_Kc_LIST must have between 1 and HOTENDS items.");
+        static_assert(WITHIN(COUNT(defKC), 1, HOTENDS), "DEFAULT_KC_LIST must have between 1 and HOTENDS items.");
      #endif
      #if ENABLED(PID_FAN_SCALING)
-        constexpr float defKf[] =
-          #ifdef DEFAULT_Kf_LIST
-            DEFAULT_Kf_LIST
+        constexpr float defKF[] =
+          #ifdef DEFAULT_KF_LIST
+            DEFAULT_KF_LIST
          #else
-            ARRAY_BY_HOTENDS1(DEFAULT_Kf)
+            ARRAY_BY_HOTENDS1(DEFAULT_KF)
          #endif
        ;
-        static_assert(WITHIN(COUNT(defKf), 1, HOTENDS), "DEFAULT_Kf_LIST must have between 1 and HOTENDS items.");
+        static_assert(WITHIN(COUNT(defKF), 1, HOTENDS), "DEFAULT_KF_LIST must have between 1 and HOTENDS items.");
      #endif
      #define PID_DEFAULT(N,E) def##N[E]
    #else
@@ -3290,11 +3290,11 @@ void MarlinSettings::reset() {
    #endif
    HOTEND_LOOP() {
      thermalManager.temp_hotend[e].pid.set(
-        PID_DEFAULT(Kp, ALIM(e, defKp)),
-        PID_DEFAULT(Ki, ALIM(e, defKi)),
-        PID_DEFAULT(Kd, ALIM(e, defKd))
-        OPTARG(PID_EXTRUSION_SCALING, PID_DEFAULT(Kc, ALIM(e, defKc)))
-        OPTARG(PID_FAN_SCALING, PID_DEFAULT(Kf, ALIM(e, defKf)))
+        PID_DEFAULT(KP, ALIM(e, defKP)),
+        PID_DEFAULT(KI, ALIM(e, defKI)),
+        PID_DEFAULT(KD, ALIM(e, defKD))
+        OPTARG(PID_EXTRUSION_SCALING, PID_DEFAULT(KC, ALIM(e, defKC)))
+        OPTARG(PID_FAN_SCALING, PID_DEFAULT(KF, ALIM(e, defKF)))
      );
    }
  #endif
@@ -3308,14 +3308,14 @@ void MarlinSettings::reset() {
  // Heated Bed PID
  //
  #if ENABLED(PIDTEMPBED)
-    thermalManager.temp_bed.pid.set(DEFAULT_bedKp, DEFAULT_bedKi, DEFAULT_bedKd);
+    thermalManager.temp_bed.pid.set(DEFAULT_BED_KP, DEFAULT_BED_KI, DEFAULT_BED_KD);
  #endif

  //
  // Heated Chamber PID
  //
  #if ENABLED(PIDTEMPCHAMBER)
-    thermalManager.temp_chamber.pid.set(DEFAULT_chamberKp, DEFAULT_chamberKi, DEFAULT_chamberKd);
+    thermalManager.temp_chamber.pid.set(DEFAULT_CHAMBER_KP, DEFAULT_CHAMBER_KI, DEFAULT_CHAMBER_KD);
  #endif

  //
--- a/Marlin/src/module/stepper.cpp
+++ b/Marlin/src/module/stepper.cpp
@@ -1454,11 +1454,7 @@ HAL_STEP_TIMER_ISR() {
  HAL_timer_isr_epilogue(MF_TIMER_STEP);
 }

-#ifdef CPU_32_BIT
-  #define STEP_MULTIPLY(A,B) MultiU32X24toH32(A, B)
-#else
-  #define STEP_MULTIPLY(A,B) MultiU24X32toH16(A, B)
-#endif
+#define STEP_MULTIPLY(A,B) TERN(CPU_32_BIT, MultiU32X24toH32, MultiU24X32toH16)(A, B)

 void Stepper::isr() {

--- a/Marlin/src/module/temperature.cpp
+++ b/Marlin/src/module/temperature.cpp
@@ -839,14 +839,14 @@ volatile bool Temperature::raw_temps_ready = false;
        TERN_(HOST_PROMPT_SUPPORT, hostui.notify(GET_TEXT_F(MSG_PID_AUTOTUNE_DONE)));

        #if ANY(PIDTEMPBED, PIDTEMPCHAMBER)
-          FSTR_P const estring = GHV(F("chamber"), F("bed"), FPSTR(NUL_STR));
-          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("Kp ", tune_pid.p);
-          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("Ki ", tune_pid.i);
-          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("Kd ", tune_pid.d);
+          FSTR_P const estring = GHV(F("CHAMBER_"), F("BED_"), FPSTR(NUL_STR));
+          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("KP ", tune_pid.p);
+          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("KI ", tune_pid.i);
+          say_default_(); SERIAL_ECHOF(estring); SERIAL_ECHOLNPGM("KD ", tune_pid.d);
        #else
-          say_default_(); SERIAL_ECHOLNPGM("Kp ", tune_pid.p);
-          say_default_(); SERIAL_ECHOLNPGM("Ki ", tune_pid.i);
-          say_default_(); SERIAL_ECHOLNPGM("Kd ", tune_pid.d);
+          say_default_(); SERIAL_ECHOLNPGM("KP ", tune_pid.p);
+          say_default_(); SERIAL_ECHOLNPGM("KI ", tune_pid.i);
+          say_default_(); SERIAL_ECHOLNPGM("KD ", tune_pid.d);
        #endif

        auto _set_hotend_pid = [](const uint8_t tool, const raw_pid_t &in_pid) {
--- a/Marlin/src/pins/pins.h
+++ b/Marlin/src/pins/pins.h
@@ -178,9 +178,9 @@
 #elif MB(DAGOMA_F5)
  #include "ramps/pins_DAGOMA_F5.h"                 // ATmega2560                           env:mega2560
 #elif MB(FYSETC_F6_13)
-  #include "ramps/pins_FYSETC_F6_13.h"              // ATmega2560                           env:FYSETC_F6
+  #include "ramps/pins_FYSETC_F6_13.h"              // ATmega2560                           env:mega2560ext
 #elif MB(FYSETC_F6_14)
-  #include "ramps/pins_FYSETC_F6_14.h"              // ATmega2560                           env:FYSETC_F6
+  #include "ramps/pins_FYSETC_F6_14.h"              // ATmega2560                           env:mega2560ext
 #elif MB(DUPLICATOR_I3_PLUS)
  #include "ramps/pins_DUPLICATOR_I3_PLUS.h"        // ATmega2560                           env:mega2560
 #elif MB(VORON)
@@ -449,33 +449,33 @@
 //

 #elif MB(DUE3DOM)
-  #include "sam/pins_DUE3DOM.h"                     // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_DUE3DOM.h"                     // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(DUE3DOM_MINI)
-  #include "sam/pins_DUE3DOM_MINI.h"                // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_DUE3DOM_MINI.h"                // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RADDS)
-  #include "sam/pins_RADDS.h"                       // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RADDS.h"                       // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RAMPS_FD_V1)
-  #include "sam/pins_RAMPS_FD_V1.h"                 // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RAMPS_FD_V1.h"                 // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RAMPS_FD_V2)
-  #include "sam/pins_RAMPS_FD_V2.h"                 // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RAMPS_FD_V2.h"                 // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RAMPS_SMART_EFB, RAMPS_SMART_EEB, RAMPS_SMART_EFF, RAMPS_SMART_EEF, RAMPS_SMART_SF)
-  #include "sam/pins_RAMPS_SMART.h"                 // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RAMPS_SMART.h"                 // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RAMPS_DUO_EFB, RAMPS_DUO_EEB, RAMPS_DUO_EFF, RAMPS_DUO_EEF, RAMPS_DUO_SF)
-  #include "sam/pins_RAMPS_DUO.h"                   // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RAMPS_DUO.h"                   // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RAMPS4DUE_EFB, RAMPS4DUE_EEB, RAMPS4DUE_EFF, RAMPS4DUE_EEF, RAMPS4DUE_SF)
-  #include "sam/pins_RAMPS4DUE.h"                   // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RAMPS4DUE.h"                   // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RURAMPS4D_11)
-  #include "sam/pins_RURAMPS4D_11.h"                // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RURAMPS4D_11.h"                // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(RURAMPS4D_13)
-  #include "sam/pins_RURAMPS4D_13.h"                // SAM3X8E                              env:DUE env:DUE_USB env:DUE_debug
+  #include "sam/pins_RURAMPS4D_13.h"                // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(ULTRATRONICS_PRO)
-  #include "sam/pins_ULTRATRONICS_PRO.h"            // SAM3X8E                              env:DUE env:DUE_debug
+  #include "sam/pins_ULTRATRONICS_PRO.h"            // SAM3X8E                              env:DUE
 #elif MB(ARCHIM1)
-  #include "sam/pins_ARCHIM1.h"                     // SAM3X8E                              env:DUE_archim env:DUE_archim_debug
+  #include "sam/pins_ARCHIM1.h"                     // SAM3X8E                              env:DUE_archim
 #elif MB(ARCHIM2)
-  #include "sam/pins_ARCHIM2.h"                     // SAM3X8E                              env:DUE_archim env:DUE_archim_debug
+  #include "sam/pins_ARCHIM2.h"                     // SAM3X8E                              env:DUE_archim
 #elif MB(ALLIGATOR)
-  #include "sam/pins_ALLIGATOR_R2.h"                // SAM3X8E                              env:DUE env:DUE_debug
+  #include "sam/pins_ALLIGATOR_R2.h"                // SAM3X8E                              env:DUE
 #elif MB(CNCONTROLS_15D)
  #include "sam/pins_CNCONTROLS_15D.h"              // SAM3X8E                              env:DUE env:DUE_USB
 #elif MB(KRATOS32)
@@ -488,7 +488,7 @@
 #elif MB(PRINTRBOARD_G2)
  #include "sam/pins_PRINTRBOARD_G2.h"              // SAM3X8C                              env:DUE_USB
 #elif MB(ADSK)
-  #include "sam/pins_ADSK.h"                        // SAM3X8C                              env:DUE env:DUE_debug
+  #include "sam/pins_ADSK.h"                        // SAM3X8C                              env:DUE

 //
 // STM32 ARM Cortex-M0+
@@ -670,6 +670,8 @@
  #include "stm32f4/pins_RUMBA32_BTT.h"             // STM32F4                              env:rumba32
 #elif MB(BLACK_STM32F407VE)
  #include "stm32f4/pins_BLACK_STM32F407VE.h"       // STM32F4                              env:STM32F407VE_black
+#elif MB(BTT_SKR_MINI_E3_V3_0_1)
+  #include "stm32f4/pins_BTT_SKR_MINI_E3_V3_0_1.h"  // STM32F4                              env:STM32F401RC_btt env:STM32F401RC_btt_xfer
 #elif MB(BTT_SKR_PRO_V1_1)
  #include "stm32f4/pins_BTT_SKR_PRO_V1_1.h"        // STM32F4                              env:BIGTREE_SKR_PRO env:BIGTREE_SKR_PRO_usb_flash_drive
 #elif MB(BTT_SKR_PRO_V1_2)
--- a/Marlin/src/pins/pins_postprocess.h
+++ b/Marlin/src/pins/pins_postprocess.h
@@ -613,7 +613,7 @@
  #endif
 #elif X_HOME_TO_MIN
  #define X_STOP_PIN X_MIN_PIN
-#else
+#elif X_HOME_TO_MAX
  #define X_STOP_PIN X_MAX_PIN
 #endif
 #if !defined(X2_USE_ENDSTOP) && ENABLED(X_DUAL_ENDSTOPS) && PIN_EXISTS(X_STOP)
@@ -635,7 +635,7 @@
    #endif
  #elif Y_HOME_TO_MIN
    #define Y_STOP_PIN Y_MIN_PIN
-  #else
+  #elif Y_HOME_TO_MAX
    #define Y_STOP_PIN Y_MAX_PIN
  #endif
  #if !defined(Y2_USE_ENDSTOP) && ENABLED(Y_DUAL_ENDSTOPS) && PIN_EXISTS(Y_STOP)
@@ -658,7 +658,7 @@
    #endif
  #elif Z_HOME_TO_MIN
    #define Z_STOP_PIN Z_MIN_PIN
-  #else
+  #elif Z_HOME_TO_MAX
    #define Z_STOP_PIN Z_MAX_PIN
  #endif
  #if ENABLED(Z_MULTI_ENDSTOPS) && PIN_EXISTS(Z_STOP)
@@ -689,7 +689,7 @@
    #endif
  #elif I_HOME_TO_MIN
    #define I_STOP_PIN I_MIN_PIN
-  #else
+  #elif I_HOME_TO_MAX
    #define I_STOP_PIN I_MAX_PIN
  #endif
 #else
@@ -712,7 +712,7 @@
    #endif
  #elif J_HOME_TO_MIN
    #define J_STOP_PIN J_MIN_PIN
-  #else
+  #elif J_HOME_TO_MAX
    #define J_STOP_PIN J_MAX_PIN
  #endif
 #else
@@ -735,7 +735,7 @@
    #endif
  #elif K_HOME_TO_MIN
    #define K_STOP_PIN K_MIN_PIN
-  #else
+  #elif K_HOME_TO_MAX
    #define K_STOP_PIN K_MAX_PIN
  #endif
 #else
@@ -758,7 +758,7 @@
    #endif
  #elif U_HOME_TO_MIN
    #define U_STOP_PIN U_MIN_PIN
-  #else
+  #elif U_HOME_TO_MAX
    #define U_STOP_PIN U_MAX_PIN
  #endif
 #else
@@ -781,7 +781,7 @@
    #endif
  #elif V_HOME_TO_MIN
    #define V_STOP_PIN V_MIN_PIN
-  #else
+  #elif V_HOME_TO_MAX
    #define V_STOP_PIN V_MAX_PIN
  #endif
 #else
@@ -804,7 +804,7 @@
    #endif
  #elif W_HOME_TO_MIN
    #define W_STOP_PIN W_MIN_PIN
-  #else
+  #elif W_HOME_TO_MAX
    #define W_STOP_PIN W_MAX_PIN
  #endif
 #else
--- a/Marlin/src/pins/ramps/pins_RAMPS.h
+++ b/Marlin/src/pins/ramps/pins_RAMPS.h
@@ -484,15 +484,15 @@
 #endif

 //
-// AUX1    5V  GND D2  D1
+// AUX1    5V  GND D1  D0
 //          2   4   6   8
 //          1   3   5   7
 //         5V  GND A3  A4
 //
 #define AUX1_05                               57  // (A3)
-#define AUX1_06                                2
+#define AUX1_06                                1  // TX0
 #define AUX1_07                               58  // (A4)
-#define AUX1_08                                1
+#define AUX1_08                                0  // RX0

 //
 // AUX2    GND A9 D40 D42 A11
--- a/Marlin/src/pins/samd/pins_MINITRONICS20.h
+++ b/Marlin/src/pins/samd/pins_MINITRONICS20.h
@@ -22,7 +22,9 @@
 #pragma once

 /**
- * ReprapWorld's Minitronics v2.0
+ * ReprapWorld Minitronics v2.0
+ * https://reprap.org/wiki/Minitronics_20
+ * 48MHz Atmel SAMD21J18 ARM Cortex-M0+
 */

 #if NOT_TARGET(__SAMD21__)
@@ -125,6 +127,11 @@

 #endif

+// Verify that drivers match the hardware
+#if (HAS_X_AXIS && !AXIS_DRIVER_TYPE_X(DRV8825)) || (HAS_Y_AXIS && !AXIS_DRIVER_TYPE_Y(DRV8825)) || (HAS_Z_AXIS && !AXIS_DRIVER_TYPE_Z(DRV8825)) || (HAS_EXTRUDER && !AXIS_DRIVER_TYPE_E0(DRV8825))
+  #error "Minitronics v2.0 has hard-wired DRV8825 drivers. Comment out this line to continue."
+#endif
+
 //
 // Extruder / Bed
 //
--- a/README.md
+++ b/README.md
@@ -60,12 +60,15 @@ Every new HAL opens up a world of hardware. At this time we need HALs for RP2040
  [STM32F7x6](//www.st.com/en/microcontrollers-microprocessors/stm32f7x6.html)|ARM® Cortex-M7|The Borg, RemRam V1
  [STM32G0B1RET6](//www.st.com/en/microcontrollers-microprocessors/stm32g0x1.html)|ARM® Cortex-M0+|BigTreeTech SKR mini E3 V3.0
  [STM32H743xIT6](//www.st.com/en/microcontrollers-microprocessors/stm32h743-753.html)|ARM® Cortex-M7|BigTreeTech SKR V3.0, SKR EZ V3.0, SKR SE BX V2.0/V3.0
+  [SAMD21P20A](//www.adafruit.com/product/4064)|ARM® Cortex-M0+|Adafruit Grand Central M4
  [SAMD51P20A](//www.adafruit.com/product/4064)|ARM® Cortex-M4|Adafruit Grand Central M4
-  [Teensy 3.5](//www.pjrc.com/store/teensy35.html)|ARM® Cortex-M4|
-  [Teensy 3.6](//www.pjrc.com/store/teensy36.html)|ARM® Cortex-M4|
-  [Teensy 4.0](//www.pjrc.com/store/teensy40.html)|ARM® Cortex-M7|
-  [Teensy 4.1](//www.pjrc.com/store/teensy41.html)|ARM® Cortex-M7|
-  Linux Native|x86/ARM/etc.|Raspberry Pi
+  [Teensy 3.2/3.1](//www.pjrc.com/teensy/teensy31.html)|MK20DX256VLH7 ARM® Cortex-M4|
+  [Teensy 3.5](//www.pjrc.com/store/teensy35.html)|MK64FX512-VMD12 ARM® Cortex-M4|
+  [Teensy 3.6](//www.pjrc.com/store/teensy36.html)|MK66FX1MB-VMD18 ARM® Cortex-M4|
+  [Teensy 4.0](//www.pjrc.com/store/teensy40.html)|MIMXRT1062-DVL6B ARM® Cortex-M7|
+  [Teensy 4.1](//www.pjrc.com/store/teensy41.html)|MIMXRT1062-DVJ6B ARM® Cortex-M7|
+  Linux Native|x86 / ARM / RISC-V|Raspberry Pi GPIO
+  Simulator|Windows, macOS, Linux|Desktop OS
  [All supported boards](//marlinfw.org/docs/hardware/boards.html#boards-list)|All platforms|All boards

 ## Marlin Support
--- a/buildroot/bin/build_all_examples
+++ b/buildroot/bin/build_all_examples
@@ -2,21 +2,22 @@
 #
 # Usage:
 #
-#  build_all_examples [-b|--branch=<branch>] - Branch to fetch from Configurations repo (import-2.1.x)
+#  build_all_examples [-a|--archive]         - Copy the binary to the export location
 #                     [-B|--base]            - Base path of configurations, overriding -b
+#                     [-b|--branch=<branch>] - Branch to fetch from Configurations repo (import-2.1.x)
 #                     [-c|--continue]        - Continue the paused build
-#                     [-p|--purge]           - Purge the status file and start over
-#                     [-s|--skip]            - Continue the paused build, skipping one
-#                     [-r|--resume=<path>]   - Start at some config in the filesystem order
-#                     [-l|--limit=#]         - Limit the number of builds in this run
-#                     [-d|--debug]           - Print extra debug output (after)
-#                     [-n|--nobuild]         - Don't actually build anything
+#                     [-d|-v|--debug]        - Print extra debug output (after)
+#                     [-e|--export=N]        - Set CONFIG_EXPORT and export to the export location
 #                     [-f|--nofail]          - Don't stop on a failed build
-#                     [-e|--export=N]        - Set CONFIG_EXPORT and export into each config folder
-#                     [-a|--archive]         - Copy the binary to the export location
+#                     [-h|--help]            - Print usage and exit
+#                     [-l|--limit=#]         - Limit the number of builds in this run
+#                     [-m|--many]            - Build all the environments for each example
+#                     [-n|--nobuild]         - Don't actually build anything
 #                     [-o|--output]          - Redirect export / archiving to another location
 #                                              (By default export to origin config folders)
-#                     [-h|--help]            - Print usage and exit
+#                     [-p|--purge]           - Purge the status file and start over
+#                     [-r|--resume=<path>]   - Start at some config in the filesystem order
+#                     [-s|--skip]            - Continue the paused build, skipping one
 #

 HERE=`dirname $0`
@@ -29,21 +30,22 @@ STAT_FILE=./.pio/.buildall

 usage() { echo "Usage:

-build_all_examples [-b|--branch=<branch>] - Branch to fetch from Configurations repo (import-2.1.x)
+build_all_examples [-a|--archive]         - Copy the binary to the export location
                   [-B|--base]            - Base path of configurations, overriding -b
+                   [-b|--branch=<branch>] - Branch to fetch from Configurations repo (import-2.1.x)
                   [-c|--continue]        - Continue the paused build
-                   [-p|--purge]           - Purge the status file and start over
-                   [-s|--skip]            - Continue the paused build, skipping one
-                   [-r|--resume=<path>]   - Start at some config in the filesystem order
+                   [-d|-v|--debug]        - Print extra debug output (after)
                   [-e|--export=N]        - Set CONFIG_EXPORT and export to the export location
-                   [-a|--archive]         - Copy the binary to the export location
-                   [-o|--output]          - Redirect export / archiving to another location
-                                            (By default export to origin config folders)
-                   [-d|--debug]           - Print extra debug output (after)
-                   [-l|--limit=#]         - Limit the number of builds in this run
-                   [-n|--nobuild]         - Don't actually build anything
                   [-f|--nofail]          - Don't stop on a failed build
                   [-h|--help]            - Print usage and exit
+                   [-l|--limit=#]         - Limit the number of builds in this run
+                   [-m|--many]            - Build all the environments for each example
+                   [-n|--nobuild]         - Don't actually build anything
+                   [-o|--output]          - Redirect export / archiving to another location
+                                            (By default export to origin config folders)
+                   [-p|--purge]           - Purge the status file and start over
+                   [-r|--resume=<path>]   - Start at some config in the filesystem order
+                   [-s|--skip]            - Continue the paused build, skipping one
 "
 }

@@ -53,27 +55,29 @@ unset FIRST_CONF
 EXIT_USAGE=
 LIMIT=1000

-while getopts 'aB:b:ce:fdhl:no:pr:sv-:' OFLAG; do
+while getopts 'aB:b:cde:fhl:mno:pr:sv-:' OFLAG; do
  case "${OFLAG}" in
    a) ARCHIVE=1                ; bugout "Archiving" ;;
    B) CBASE=${OPTARG%/}        ; bugout "Base: $CBASE" ;;
    b) BRANCH=$OPTARG           ; bugout "Branch: $BRANCH" ;;
-    f) NOFAIL=1                 ; bugout "Continue on Fail" ;;
-    r) ISRES=1 ; FIRST_CONF=$OPTARG ; bugout "Resume: $FIRST_CONF" ;;
    c) CONTINUE=1               ; bugout "Continue" ;;
-    s) CONTSKIP=1               ; bugout "Continue, skipping" ;;
+  d|v) DEBUG=1                  ; bugout "Debug ON" ;;
    e) CEXPORT=$OPTARG          ; bugout "Export $CEXPORT" ;;
-    o) OUTBASE="${OPTARG%/}"    ; bugout "Archive to $OUTBASE" ;;
+    f) NOFAIL=1                 ; bugout "Continue on Fail" ;;
    h) EXIT_USAGE=1 ; break ;;
    l) LIMIT=$OPTARG            ; bugout "Limit to $LIMIT build(s)" ;;
-  d|v) DEBUG=1                  ; bugout "Debug ON" ;;
+    m) MANY=1                   ; bugout "Many Envs" ;;
    n) DRYRUN=1                 ; bugout "Dry Run" ;;
+    o) OUTBASE="${OPTARG%/}"    ; bugout "Archive to $OUTBASE" ;;
    p) PURGE=1                  ; bugout "Purge stat file" ;;
+    r) ISRES=1 ; FIRST_CONF=$OPTARG ; bugout "Resume: $FIRST_CONF" ;;
+    s) CONTSKIP=1               ; bugout "Continue, skipping" ;;
    -) ONAM="${OPTARG%%=*}" ; OVAL="${OPTARG#*=}"
       case "$ONAM" in
      archive) ARCHIVE=1        ; bugout "Archiving" ;;
         base) CBASE=${OVAL%/}  ; bugout "Base: $CBASE" ;;
       branch) BRANCH=$OVAL     ; bugout "Branch: $BRANCH" ;;
+         many) MANY=1           ; bugout "Many Envs" ;;
       nofail) NOFAIL=1         ; bugout "Continue on Fail" ;;
       resume) ISRES=1 ; FIRST_CONF=$OVAL ; bugout "Resume: $FIRST_CONF" ;;
     continue) CONTINUE=1       ; bugout "Continue" ;;
@@ -154,7 +158,9 @@ shopt -s nullglob
 export PAUSE=1

 # Get a list of all folders that contain a file matching "Configuration*.h"
-find -ds "$CBASE"/config/examples -type d -name 'Configuration.h' -o -name 'Configuration_adv.h' -print0 | while IFS= read -r -d $'\0' CONF; do
+find "$CBASE"/config/examples -type d -name 'Configuration.h' -o -name 'Configuration_adv.h' -print0 \
+  | LC_ALL=C sort -fz \
+  | while IFS= read -r -d $'\0' CONF; do

  # Remove the file name and slash from the end of the path
  CONF=${CONF%/*}
@@ -179,6 +185,9 @@ find -ds "$CBASE"/config/examples -type d -name 'Configuration.h' -o -name 'Conf
  # Exporting? Add -e argument
  ((CEXPORT)) && CARGS+=("-e" "$CEXPORT")

+  # Build many environments? Add -m argument
+  ((MANY)) && CARGS+=("-m")
+
  # Continue on fail? Add -f argument
  ((NOFAIL)) && CARGS+=("-f")

--- a/buildroot/bin/build_example
+++ b/buildroot/bin/build_example
@@ -4,11 +4,14 @@
 #
 #  build_example  -b|--base=<path>    - Configurations root folder (e.g., ./.pio/build-BRANCH)
 #                 -c|--config=<rel>   - Sub-path of the configs to build (within config/examples)
+#                [-n|--index=N]       - Which environment to build, by index (Based on pins.h comments)
+#                [-m|--many]          - Build all the board's environments listed in pins.h
 #                [-e|--export=N]      - Use CONFIG_EXPORT N to export the config to the export location
 #                [-a|--archive]       - Archive the build (to the export location)
 #                [-o|--output]        - Redirect export / archiving to another location
 #                                       (By default export to origin config folder)
 #                [-f|--nofail]        - Don't stop on a failed build
+#                [-x|--noxfer]        - Skip the build if the env ends with _xfer. Implied with --many.
 #                [-w|--nowarn]        - Suppress warnings with extra config options
 #                [-r|--reveal]        - Reveal the config/export folder after the build
 #                [-h|--help]          - Print usage and exit
@@ -19,11 +22,14 @@ usage() { echo "Usage:

 build_example  -b|--base=<path>    - Configurations root folder (e.g., ./.pio/build-BRANCH)
               -c|--config=<rel>   - Sub-path of the configs to build (within config/examples)
+              [-n|--index=N]       - Which environment to build, by index (Based on pins.h comments)
+              [-m|--many]          - Build all the board's environments listed in pins.h
              [-e|--export=N]      - Use CONFIG_EXPORT N to export the config to the export location
              [-a|--archive]       - Archive the build (to the export location)
              [-o|--output]        - Redirect export / archiving to another location
                                     (By default export to origin config folder)
              [-f|--nofail]        - Don't stop on a failed build
+              [-x|--noxfer]        - Skip the build if the env ends with _xfer. Implied with --many.
              [-w|--nowarn]        - Suppress warnings with extra config options
              [-r|--reveal]        - Reveal the config/export folder after the build
              [-h|--help]          - Print usage and exit
@@ -50,27 +56,37 @@ REVEAL=
 EXPNUM=
 NOFAIL=
 OUTBASE=
-while getopts 'ab:c:e:fhio:r-:' OFLAG; do
+BUILDINDEX=1
+MANY=
+NOXFER=
+
+while getopts 'ab:c:e:fhmn:o:r-:x' OFLAG; do
  case "${OFLAG}" in
    a) ARCHIVE=1 ;;
    b) BASE="${OPTARG%/}" ;;
    c) CONFIG="${OPTARG%/}" ;;
    e) EXPNUM="$OPTARG" ;;
-    o) OUTBASE="${OPTARG%/}" ;;
-    h) EXIT_USAGE=1 ; break ;;
    f) NOFAIL=1 ;;
+    h) EXIT_USAGE=1 ; break ;;
+    m) MANY=1 ; NOXFER=1 ;;
+    n) BUILDINDEX="$OPTARG" ;;
+    o) OUTBASE="${OPTARG%/}" ;;
    r) REVEAL=1 ;;
+    x) NOXFER=1 ;;
    -) ONAM="${OPTARG%%=*}" ; OVAL="${OPTARG#*=}"
       case "$ONAM" in
        archive) ARCHIVE=1 ;;
          allow) ALLOW=1 ;;
           base) BASE="${OVAL%/}" ;;
         config) CONFIG="${OVAL%/}" ;;
+           many) MANY=1 ; NOXFER=1 ;;
+          index) BUILDINDEX="$OVAL" ;;
         export) EXPNUM="$OVAL" ;;
         output) OUTBASE="${OVAL%/}" ;;
           help) EXIT_USAGE=1 ; break ;;
         nofail) NOFAIL=1 ;;
         reveal) REVEAL=1 ;;
+         noxfer) NOXFER=1 ;;
              *) EXIT_USAGE=2 ; echo "$SELF: unrecognized option \`--$ONAM'" ; break ;;
       esac
       ;;
@@ -154,11 +170,12 @@ ENAME=("-name" "marlin_config.json" \
  "-o" "-name" "schema.yml")

 # Possible built firmware names (in the build folder)
-BNAME=("-name" 'firmware*.hex' \
+BNAME=("-name" "firmware*.hex" \
  "-o" "-name" "firmware*.bin" \
  "-o" "-name" "project*.bin" \
  "-o" "-name" "Robin*.bin" \
-  "-o" "-name" "main_*.bin")
+  "-o" "-name" "main_*.bin" \
+  "-o" "-name" "MarlinSimulator*")

 mkdir -p "$BUILD"

@@ -166,64 +183,122 @@ mkdir -p "$BUILD"
 if [[ $EXPNUM ]]; then
  opt_set CONFIG_EXPORT $EXPNUM
  # Clean up old exports
-  find "$BUILD" \( "${ENAME[@]}" \) -exec rm "{}" \;
+  find "$BUILD" -type f \( "${ENAME[@]}" \) -exec rm "{}" \;
 fi

-((ARCHIVE)) && find "$BUILD" \( "${BNAME[@]}" \) -exec rm "{}" \;
+((ARCHIVE)) && find "$BUILD" -type f \( "${BNAME[@]}" \) -exec rm "{}" \;

-set +e
+echo "Building example $CONFIG..."

-echo "Building example $CONFIG ..."
-mftest -s -a -n1 ; ERR=$?
+# If doing many builds get a list of all environment names,
+# which also gives us the number of environments.
+if ((MANY)); then
+  ENVLIST=$(mfenvs) # BOARD_NAME_STRING (1234): [ env1 env2 env3 ... ]
+  ENVLIST=${ENVLIST##*: [ }
+  ENVARRAY=(${ENVLIST% ]})
+  ENVCOUNT=${#ENVARRAY[*]}
+  ((ENVCOUNT)) || { alrt "mfenvs failed for this board." ; exit 1 ; }
+  echo "Found $ENVCOUNT environment(s): ${ENVARRAY[*]}"
+fi

-((ERR)) && alrt "Failed ($ERR)" || annc "Success"
+# Run one or more builds based on --many
+# Build all from BUILDINDEX onward (usually 1) meaning ALL.
+# MANY with a BUILDINDEX may be useful for continuing an interrupted build.

-set -e
+while true; do
+  set +e

-if [[ $ERR -gt 0 ]]; then
+  # Skip over "_xfer" environments when specified
+  if [[ -n $NOXFER && ${ENVARRAY[BUILDINDEX-1]} =~ _xfer$ ]]; then
+
+    echo "Skipping example $CONFIG ($BUILDINDEX)..."

-  # Error? For --nofail simply log. Otherwise return the error.
-  if [[ -n $NOFAIL ]]; then
-    date +"%F %T [FAIL] $CONFIG" >>./.pio/error-log.txt
  else
-    exit $ERR
+
+    echo "Building example $CONFIG ($BUILDINDEX)..."
+
+    # Run a build and record the error number
+    mftest -s -a -n$BUILDINDEX ; ERR=$?
+
+    # "Index out of range" can fail without an error
+    ((MANY)) && ((ERR == 66)) && ERR=0 && break  # "index out of range"
+
+    set -e
+
+    if [[ $ERR -gt 0 ]]; then
+
+      alrt "Failed ($ERR)"
+
+      # Error? For --nofail simply log. Otherwise return the error.
+      if [[ -n $NOFAIL ]]; then
+        date +"%F %T [FAIL] $CONFIG ($BUILDINDEX)" >>./.pio/error-log.txt
+      else
+        exit $ERR
+      fi
+
+    else
+
+      annc "Success"
+
+      # Copy exports back to the configs
+      if [[ -n $EXPNUM ]]; then
+        annc "Exporting $EXPNUM"
+        [[ -f Marlin/Config-export.h ]] && { cp Marlin/Config-export.h "$ARCSUB"/Config.h ; }
+        find "$BUILD" -type f \( "${ENAME[@]}" \) -exec cp "{}" "$ARCSUB" \;
+      fi
+
+      # When building many, create sub-folders for each build env name
+      if [[ -n $MANY ]]; then
+        ENV=${ENVARRAY[BUILDINDEX-1]}
+        ARCENVSUB="$ARCSUB/$ENV"
+      else
+        ARCENVSUB="$ARCSUB"
+      fi
+
+      # Copy potential firmware files into the config folder
+      # TODO: Consider firmware that needs an STM32F4_UPDATE folder.
+      #       Currently only BOARD_CREALITY_F401RE env:STM32F401RE_creality
+      if ((ARCHIVE)); then
+        annc "Archiving"
+        find "$BUILD" -type f \( "${BNAME[@]}" \) -exec sh -c '
+          ARCDIR="$1" ; CONFIG="$2" ; FILE="$3" ; shift 3
+          NAME=${FILE##*/} ; SHRT=${NAME%.*} ; DIR=${FILE%/*}
+          ZIPX=
+          if [[ $CONFIG == *Simulator* ]]; then
+            case $(uname | tr '[:upper:]' '[:lower:]') in
+              darwin) SUB="macOS" ; ZIPX="-X" ;;
+              *linux) SUB="Linux" ;;
+                win*) SUB="Windows" ;;
+               msys*) SUB="Windows" ;;
+             cygwin*) SUB="Windows" ;;
+              mingw*) SUB="Windows" ;;
+                   *) SUB='Unix' ;;
+            esac
+            ARCH=$(uname -m | tr '[:lower:]' '[:upper:]')
+            ARCDIR="$ARCDIR/$SUB-$ARCH"
+          fi
+          mkdir -p "$ARCDIR"
+          rm -f "$ARCDIR"/*.zip "$ARCDIR"/*.sha256.txt
+          cd "$DIR"
+          SHASUM=$(sha256sum "$NAME" | cut -d" " -f1)
+          echo "$CONFIG\n$SHASUM" > "$ARCDIR/$NAME.sha256.txt"
+          zip $ZIPX "$ARCDIR/$SHRT.zip" "$NAME" && rm "$NAME"
+          cd - >/dev/null
+        ' sh "$ARCENVSUB" "$CONFIG" {} +
+      fi # ARCHIVE
+
+      # Reveal the configs after the build, if requested
+      ((REVEAL)) && { annc "Revealing $ARCENVSUB" ; open "$ARCENVSUB" ; }
+
+    fi # Success
+
  fi

-else
+  ((MANY)) || break # Only one build if not --many

-  # Copy exports back to the configs
-  if [[ -n $EXPNUM ]]; then
-    annc "Exporting $EXPNUM"
-    [[ -f Marlin/Config-export.h ]] && { cp Marlin/Config-export.h "$ARCSUB"/Config.h ; }
-    find "$BUILD" \( "${ENAME[@]}" \) -exec cp "{}" "$ARCSUB" \;
-  fi
+  # Set up for the next build, if there is one
+  ((++BUILDINDEX > ENVCOUNT)) && break

-  # Copy potential firmware files into the config folder
-  # TODO: Consider firmware that needs an STM32F4_UPDATE folder.
-  #       Currently only BOARD_CREALITY_F401RE env:STM32F401RE_creality
-  if ((ARCHIVE)); then
-    annc "Archiving"
-    rm -f "$ARCSUB"/*.bin.tar.gz "$ARCSUB"/*.hex.tar.gz
-    find "$BUILD" \( "${BNAME[@]}" \) -exec sh -c '
-      ARCSUB="$1"
-      CONFIG="$2"
-      shift 2
-      for FILE in "$@"; do
-        cd "${FILE%/*}"
-        NAME=${FILE##*/}
-        SHRT=${NAME%.*}
-        SHASUM=$(sha256sum "$NAME" | cut -d" " -f1)
-        tar -czf "$ARCSUB/$SHRT.tar.gz" "$NAME"
-        echo "$CONFIG\n$SHASUM" > "$ARCSUB/$NAME.sha256.txt"
-        rm "$NAME"
-        cd - >/dev/null
-      done
-    ' sh "$ARCSUB" "$CONFIG" {} +
-  fi
-
-  # Reveal the configs after the build, if requested
-  ((REVEAL)) && { annc "Revealing $ARCSUB" ; open "$ARCSUB" ; }
-
-fi
+done

 exit 0
--- a/buildroot/bin/mfenvs
+++ b/buildroot/bin/mfenvs
@@ -0,0 +1,35 @@
+#!/usr/bin/env bash
+#
+#  mfenvs   Print the current board and environment information
+#           Use -n to remove "*_xfer" environments from the list.
+#           Output -> "SHORT_NAME (###): [ env1 env2 env3 ... ]"
+#
+
+[[ -d Marlin/src ]] || { echo "Please 'cd' to the Marlin repo root." ; exit 1 ; }
+which pio >/dev/null || { echo "Make sure 'pio' is in your execution PATH." ; exit 1 ;  }
+
+errout() { echo -e "\033[0;31m$1\033[0m" ; }
+
+case $(uname | tr '[:upper:]' '[:lower:]') in
+  darwin) SYS='mac' ;;
+  *linux) SYS='lin' ;;
+    win*) SYS='win' ;;
+   msys*) SYS='win' ;;
+ cygwin*) SYS='win' ;;
+  mingw*) SYS='win' ;;
+       *) SYS='uni' ;;
+esac
+
+ACODE='/^[[:space:]]*#define[[:space:]]MOTHERBOARD[[:space:]]/ { sub(/^BOARD_/, "", $3); print $3 }'
+MB=$(awk "$ACODE" Marlin/Configuration.h 2>/dev/null)
+[[ -z $MB ]] && MB=$(awk "$ACODE" Marlin/Config.h 2>/dev/null)
+[[ -z $MB ]] && { echo "Error - Can't read MOTHERBOARD setting." ; exit 1 ; }
+BLINE=$( grep -E "define\s+BOARD_$MB\b" Marlin/src/core/boards.h )
+BNUM=$( sed -E 's/^.+BOARD_[^ ]+ +([0-9]+).+$/\1/' <<<"$BLINE" )
+[[ -z $BNUM ]] && { echo "Error - Can't find BOARD_$MB in core/boards.h." ; exit 1 ; }
+ENVS=( $( grep -EA1 "MB\(.*\b$MB\b.*\)" Marlin/src/pins/pins.h | grep -E "#include.+//.+(env|$SYS):[^ ]+" | grep -oE "(env|$SYS):[^ ]+" | sed -E "s/(env|$SYS)://" ) )
+[[ "$1" = "-n" ]] && ENVS=( $(printf "%s\n" "${ENVS[@]}" | grep -v "_xfer$") )
+[[ -z $ENVS ]] && { errout "Error - Can't find target(s) for $MB ($BNUM)." ; exit 1 ; }
+ECOUNT=${#ENVS[*]}
+[[ $ECOUNT == 1 ]] && EOUT=$ENVS || EOUT="${ENVS[@]}"
+echo "$MB ($BNUM): [ $EOUT ]"
--- a/buildroot/bin/mftest
+++ b/buildroot/bin/mftest
@@ -16,23 +16,24 @@ bugout() { ((DEBUG)) && echo -e "\033[0;32m$1\033[0m" ; }

 usage() {
  echo "
-Usage: mftest [-t|--env=<env|index>] [-n|--num=<num>] [-m|--make] [-y|--build=<Y|n>]
-       mftest [-a|--autobuild]
+Usage: mftest [-a|--autobuild]
       mftest [-r|--rebuild]
       mftest [-s|--silent]
+       mftest [-t|--env=<env|index>] [-n|--num=<num>] [-m|--make] [-y|--build=<Y|n>]
       mftest [-u|--autoupload] [-n|--num=<num>]

 OPTIONS
-  -t --env         The environment to apply / run, or the menu index number.
-  -n --num         The index of the test to run. (In file order.)
-  -m --make        Use the make / Docker method for the build.
-  -y --build       Skip 'Do you want to build this test?' and assume YES.
-  -h --help        Print this help.
  -a --autobuild   PIO Build using the MOTHERBOARD environment.
+  -d --default     Restore to defaults before applying configs.
+  -h --help        Print this help.
+  -m --make        Use the make / Docker method for the build.
+  -n --num         The index of the test to run. (In file order.)
+  -r --rebuild     Rebuild previous PIO Build.
+  -s --silent      Silence build output from PlatformIO.
+  -t --env         The environment to apply / run, or the menu index number.
  -u --autoupload  PIO Upload using the MOTHERBOARD environment.
  -v --verbose     Extra output for debugging.
-  -s --silent      Silence build output from PlatformIO.
-  -d --default     Restore to defaults before applying configs.
+  -y --build       Skip 'Do you want to build this test?' and assume YES.

 env shortcuts: tree due esp lin lp8|lpc8 lp9|lpc9 m128 m256|mega stm|f1 f4 f7 s6 teensy|t31|t32 t35|t36 t40|t41
 "
@@ -56,7 +57,7 @@ TESTENV='-'
 CHOICE=0
 DEBUG=0

-while getopts 'abdhmrsuvyn:t:-:' OFLAG; do
+while getopts 'adhmn:rst:uvy-:' OFLAG; do
  case "${OFLAG}" in
    a) AUTO_BUILD=1 ; bugout "Auto-Build target..." ;;
    d) DL_DEFAULTS=1 ; bugout "Restore to defaults..." ;;
@@ -195,7 +196,7 @@ if ((AUTO_BUILD)); then
      fi
    else
      echo "Detected \"$BDESC\" | $MB ($BNUM)."
-      [[ $CHOICE > $ECOUNT ]] && { echo "Environment selection out of range." ; exit 1 ; }
+      [[ $CHOICE > $ECOUNT ]] && { echo "Environment selection out of range." ; exit 66 ; }
    fi
    TARGET="${ENVS[$CHOICE-1]}"
    if [[ $MB == 'SIMULATED' && $TARGET == 'linux_native' ]]; then
--- a/buildroot/bin/opt_disable
+++ b/buildroot/bin/opt_disable
@@ -1,6 +1,6 @@
 #!/usr/bin/env python

-import sys, os,config
+import sys, os, config

 def main():
    args = sys.argv[1:]
--- a/buildroot/bin/opt_enable
+++ b/buildroot/bin/opt_enable
@@ -1,6 +1,6 @@
 #!/usr/bin/env python

-import sys, os,config
+import sys, os, config

 def main():
    args = sys.argv[1:]
--- a/buildroot/bin/use_example_configs
+++ b/buildroot/bin/use_example_configs
@@ -1,4 +1,4 @@
-#!/usr/bin/env bash
+#!/usr/bin/env python
 #
 # use_example_configs [repo:]configpath
 #
@@ -14,40 +14,127 @@
 #       The fallback branch is bugfix-2.1.x.
 #

-which curl >/dev/null && TOOL='curl -L -s -S -f -o wgot'
-which wget >/dev/null && TOOL='wget -q -O wgot'
+import os, subprocess, sys, urllib.request, urllib.error
+from pathlib import Path

-CURR=$(git branch 2>/dev/null | grep ^* | sed 's/\* //g')
-case "$CURR" in
-   bugfix-2.*.x ) BRANCH=$CURR ;;
-  *-2.1.x|2.1.x ) BRANCH=latest-2.1.x ;;
-  *-2.0.x|2.0.x ) BRANCH=latest-2.0.x ;;
-  *-1.1.x|1.1.x ) BRANCH=latest-1.1.x ;;
-  *-1.0.x|1.0.x ) BRANCH=latest-1.0.x ;;
-              * ) BRANCH=bugfix-2.1.x ;;
-esac
+DEBUGGING = False
+CONFIG_FILES = ("Configuration.h", "Configuration_adv.h", "_Bootscreen.h", "_Statusscreen.h")

-if [[ $# > 0 ]]; then
-  IFS=: read -r PART1 PART2 <<< "$@"
-  [[ -n $PART2 ]] && { UDIR="$PART2" ; BRANCH="$PART1" ; } \
-                  || { UDIR="$PART1" ; }
-  RDIR="${UDIR// /%20}"
-  echo "Fetching $UDIR configurations from $BRANCH..."
-  EXAMPLES="examples/$RDIR"
-else
-  EXAMPLES="default"
-fi
+def debug_print(s):
+    if DEBUGGING: print(s)

-CONFIGS="https://raw.githubusercontent.com/MarlinFirmware/Configurations/$BRANCH/config/${EXAMPLES}"
+def get_current_branch():
+    try:
+        result = subprocess.run(['git', 'branch'], capture_output=True, text=True, check=True)
+        for line in result.stdout.splitlines():
+            if line.startswith('*'):
+                return line[2:]
+    except subprocess.CalledProcessError:
+        return None

-restore_configs
+def sparse_checkout(branch, config_path, repo_url="https://github.com/MarlinFirmware/Configurations.git"):
+    configs_dir = Path("ConfigurationsRepo")
+    config_subdir = f"config/{config_path}"

-cd Marlin
+    if not configs_dir.exists():
+        # Step 1: Clone with no checkout
+        subprocess.run([
+            "git", "clone", "--depth", "1", "--filter=blob:none", "--sparse",
+            "--branch", branch, repo_url, str(configs_dir)
+        ], check=True)

-$TOOL "$CONFIGS/Configuration.h"     >/dev/null 2>&1 && mv wgot Configuration.h
-$TOOL "$CONFIGS/Configuration_adv.h" >/dev/null 2>&1 && mv wgot Configuration_adv.h
-$TOOL "$CONFIGS/_Bootscreen.h"       >/dev/null 2>&1 && mv wgot _Bootscreen.h
-$TOOL "$CONFIGS/_Statusscreen.h"     >/dev/null 2>&1 && mv wgot _Statusscreen.h
+    # Step 2: Enable sparse checkout and set the folder
+    subprocess.run(["git", "sparse-checkout", "set", config_subdir], cwd=str(configs_dir), check=True)
+    # Step 3: Pull the latest for that branch/folder
+    subprocess.run(["git", "pull"], cwd=str(configs_dir), check=True)

-rm -f wgot
-cd - >/dev/null
+def copy_config_files(branch, config_path, dest_dir):
+    sparse_checkout(branch, config_path)
+
+    src_dir = Path("ConfigurationsRepo") / "config" / config_path
+    for fname in CONFIG_FILES:
+        src_file = src_dir / fname
+        if src_file.exists():
+            dest_file = dest_dir / fname
+            debug_print(f"Copying {src_file} to {dest_file}")
+            dest_file.write_bytes(src_file.read_bytes())
+        else:
+            debug_print(f"{fname} not found in {src_dir}")
+
+def fetch_config_files(branch, config_path, dest_dir):
+    config_path_url = config_path.replace(' ', '%20')
+    base_url = f"https://raw.githubusercontent.com/MarlinFirmware/Configurations/{branch}/config/{config_path_url}"
+
+    for file in CONFIG_FILES:
+        url = f"{base_url}/{file}"
+        dest_file = dest_dir / file
+        if os.getenv('DEBUG', '0') == '1':
+            debug_print(f"Fetching {file} from {url} to {dest_file}")
+
+        try:
+            urllib.request.urlretrieve(url, dest_file)
+        except urllib.error.HTTPError as e:
+            if e.code == 404:
+                if os.getenv('DEBUG', '0') == '1':
+                    print(f"File {file} not found (404), skipping.")
+            else:
+                raise
+
+def fetch_configs(branch, config_path):
+    print(f"Fetching {config_path} configurations from {branch}...")
+
+    marlin_dir = Path("Marlin")
+    if not marlin_dir.exists():
+        print(f"Directory 'Marlin' not found at the current location.")
+        sys.exit(1)
+
+    if os.environ.get('GITHUB_ACTIONS'):        # Running on GitHub ?
+        copy_config_files(branch, config_path, marlin_dir)
+    else:
+        fetch_config_files(branch, config_path, marlin_dir)
+
+def main():
+    branch = get_current_branch()
+    if not branch:
+        print("Not a git repository or no branch found.")
+        sys.exit(1)
+
+    if branch.startswith("bugfix-2."):
+        branch = branch
+    elif branch.endswith("bugfix-2.1.x"):
+        branch = "bugfix-2.1.x"
+    elif branch.endswith("-2.1.x") or branch == "2.1.x":
+        branch = "latest-2.1.x"
+    elif branch.endswith("-2.0.x") or branch == "2.0.x":
+        branch = "latest-2.0.x"
+    elif branch.endswith("-1.1.x") or branch == "1.1.x":
+        branch = "latest-1.1.x"
+    elif branch.endswith("-1.0.x") or branch == "1.0.x":
+        branch = "latest-1.0.x"
+    else:
+        branch = "bugfix-2.1.x"
+
+    if len(sys.argv) > 1:
+        arg = sys.argv[1]
+        if ':' in arg:
+            part1, part2 = arg.split(':', 1)
+            config_path = part2
+            branch = part1
+        else:
+            config_path = arg
+        config_path = 'examples/'+config_path
+    else:
+        config_path = "default"
+
+    try:
+        subprocess.run(['restore_configs'], check=True)
+    except FileNotFoundError:
+        try:
+            subprocess.run(['./buildroot/bin/restore_configs'], check=True)
+        except FileNotFoundError:
+            print("restore_configs not found, skipping.")
+
+    fetch_configs(branch, config_path)
+
+if __name__ == "__main__":
+    main()
--- a/buildroot/share/PlatformIO/scripts/chitu_crypt.py
+++ b/buildroot/share/PlatformIO/scripts/chitu_crypt.py
@@ -4,15 +4,15 @@
 #
 import pioutil
 if pioutil.is_pio_build():
-    import struct,uuid,marlin
+    import struct, uuid, marlin

-    board = marlin.env.BoardConfig()
+    board = pioutil.env.BoardConfig()

    def calculate_crc(contents, seed):
        accumulating_xor_value = seed

        for i in range(0, len(contents), 4):
-            value = struct.unpack('<I', contents[ i : i + 4])[0]
+            value = struct.unpack("<I", contents[i : i + 4])[0]
            accumulating_xor_value = accumulating_xor_value ^ value
        return accumulating_xor_value

@@ -29,12 +29,12 @@ if pioutil.is_pio_build():
        # This is the block counter
        block_number = xor_seed * block_number

-        #load the xor key from the file
-        r7 =  file_key
+        # load the xor key from the file
+        r7 = file_key

        for loop_counter in range(0, block_size):
            # meant to make sure different bits of the key are used.
-            xor_seed = int(loop_counter / key_length)
+            xor_seed = loop_counter // key_length

            # IP is a scratch register / R12
            ip = loop_counter - (key_length * xor_seed)
@@ -54,10 +54,10 @@ if pioutil.is_pio_build():
            # and then with IP
            xor_seed = xor_seed ^ ip

-            #Now store the byte back
+            # Now store the byte back
            r1[loop_counter] = xor_seed & 0xFF

-            #increment the loop_counter
+            # increment the loop_counter
            loop_counter = loop_counter + 1

    def encrypt_file(input, output_file, file_length):
@@ -82,15 +82,15 @@ if pioutil.is_pio_build():
        # write the file_key
        output_file.write(struct.pack("<I", file_key))

-        #TODO - how to enforce that the firmware aligns to block boundaries?
-        block_count = int(len(input_file) / block_size)
-        print ("Block Count is ", block_count)
+        # TODO: - how to enforce that the firmware aligns to block boundaries?
+        block_count = len(input_file) // block_size
+        print("Block Count is ", block_count)
        for block_number in range(0, block_count):
-            block_offset = (block_number * block_size)
+            block_offset = block_number * block_size
            block_end = block_offset + block_size
-            block_array = bytearray(input_file[block_offset: block_end])
+            block_array = bytearray(input_file[block_offset:block_end])
            xor_block(block_array, block_array, block_number, block_size, file_key)
-            for n in range (0, block_size):
+            for n in range(0, block_size):
                input_file[block_offset + n] = block_array[n]

            # update the expected CRC value.
--- a/buildroot/share/PlatformIO/scripts/common-cxxflags.py
+++ b/buildroot/share/PlatformIO/scripts/common-cxxflags.py
@@ -5,17 +5,19 @@

 import pioutil
 if pioutil.is_pio_build():
-    Import("env")
+    env = pioutil.env

    cxxflags = [
        # "-Wno-incompatible-pointer-types",
        # "-Wno-unused-const-variable",
        # "-Wno-maybe-uninitialized",
-        # "-Wno-sign-compare"
+        # "-Wno-sign-compare",
+        "-fno-sized-deallocation"
    ]
-    if "teensy" not in env["PIOENV"]:
+    if "teensy" not in env["PIOENV"] and "esp32" not in env["PIOENV"]:
        cxxflags += ["-Wno-register"]
    env.Append(CXXFLAGS=cxxflags)
+    env.Append(CFLAGS=["-Wno-implicit-function-declaration"])

    #
    # Add CPU frequency as a compile time constant instead of a runtime variable
@@ -27,8 +29,8 @@ if pioutil.is_pio_build():
    # Useful for JTAG debugging
    #
    # It will separate release and debug build folders.
-    # It useful to keep two live versions: a debug version for debugging and another for
-    # release, for flashing when upload is not done automatically by jlink/stlink.
+    # This is useful to keep two live versions: a debug version and a release version,
+    # for flashing when upload is not done automatically by jlink/stlink.
    # Without this, PIO needs to recompile everything twice for any small change.
    if env.GetBuildType() == "debug" and env.get("UPLOAD_PROTOCOL") not in ["jlink", "stlink", "custom"]:
        env["BUILD_DIR"] = "$PROJECT_BUILD_DIR/$PIOENV/debug"
--- a/buildroot/share/PlatformIO/scripts/pioutil.py
+++ b/buildroot/share/PlatformIO/scripts/pioutil.py
@@ -2,10 +2,11 @@
 # pioutil.py
 #

+from SCons.Script import DefaultEnvironment
+env = DefaultEnvironment()
+
 # Make sure 'vscode init' is not the current command
 def is_pio_build():
-    from SCons.Script import DefaultEnvironment
-    env = DefaultEnvironment()
    if "IsCleanTarget" in dir(env) and env.IsCleanTarget(): return False
    return not env.IsIntegrationDump()

--- a/buildroot/share/PlatformIO/scripts/preflight-checks.py
+++ b/buildroot/share/PlatformIO/scripts/preflight-checks.py
@@ -86,6 +86,16 @@ if pioutil.is_pio_build():
                    err = "ERROR: Config files found in directory %s. Please move them into the Marlin subfolder." % p
                    raise SystemExit(err)

+        #
+        # Check for DGUS_UI_IS in Configuration.h
+        #
+        config_path = epath / "Marlin" / "Configuration.h"
+        if config_path.is_file():
+            with config_path.open() as f:
+                if "DGUS_UI_IS" in f.read():
+                    err = "ERROR: Future Configurations (2.1.3 and up) are not supported for Marlin 2.1.2."
+                    raise SystemExit(err)
+
        #
        # Find the name.cpp.o or name.o and remove it
        #
--- a/buildroot/share/PlatformIO/scripts/schema.py
+++ b/buildroot/share/PlatformIO/scripts/schema.py
@@ -1,17 +1,35 @@
 #!/usr/bin/env python3
-#
-# schema.py
-#
-# Used by signature.py via common-dependencies.py to generate a schema file during the PlatformIO build
-# when CONFIG_EXPORT is defined in the configuration.
-#
-# This script can also be run standalone from within the Marlin repo to generate JSON and YAML schema files.
-#
-# This script is a companion to abm/js/schema.js in the MarlinFirmware/AutoBuildMarlin project, which has
-# been extended to evaluate conditions and can determine what options are actually enabled, not just which
-# options are uncommented. That will be migrated to this script for standalone migration.
-#
-import re,json
+"""
+schema.py
+
+Extract firmware configuration into structured JSON or YAML schema format.
+
+Used by signature.py via common-dependencies.py to generate a schema file during the
+PlatformIO build when CONFIG_EXPORT is defined in the configuration.
+
+This script can also be run standalone from within the Marlin repo, and is a companion to
+abm/js/schema.js in the MarlinFirmware/AutoBuildMarlin project, which has been extended to
+evaluate conditions and can determine what options are actually enabled, not just which
+options are uncommented. That will be migrated to this script for standalone migration.
+
+Usage: schema.py [-h] [some|json|jsons|group|yml|yaml]
+
+Process Marlin firmware configuration files (Configuration.h and Configuration_adv.h)
+to produce structured output suitable for documentation, tooling, or automated processing.
+
+Positional arguments:
+  some      Generate both JSON and YAML output (schema.json and schema.yml)
+  json      Generate JSON output (schema.json)
+  jsons     Generate grouped JSON output with wildcard options (schema.json and schema_grouped.json)
+  group     Generate grouped JSON output only (schema_grouped.json)
+  yml       Generate YAML output (schema.yml)
+  yaml      Same as 'yml'
+
+Optional arguments:
+  -h, --help  Show this help message and exit
+"""
+
+import re, json
 from pathlib import Path

 def extend_dict(d:dict, k:tuple):
@@ -43,8 +61,7 @@ def find_grouping(gdict, filekey, sectkey, optkey, pindex):
                optparts[pindex] = '*'
                wildkey = '_'.join(optparts)
                kkey = f'{filekey}|{sectkey}|{wildkey}'
-                if kkey not in gdict: gdict[kkey] = []
-                gdict[kkey].append((subkey, modkey))
+                gdict.setdefault(kkey, []).append((subkey, modkey))

 # Build a list of potential groups. Only those with multiple items will be grouped.
 def group_options(schema):
@@ -70,7 +87,7 @@ def group_options(schema):
 def load_boards():
    bpath = Path("Marlin/src/core/boards.h")
    if bpath.is_file():
-        with bpath.open() as bfile:
+        with bpath.open(encoding='utf-8') as bfile:
            boards = []
            for line in bfile:
                if line.startswith("#define BOARD_"):
@@ -80,7 +97,7 @@ def load_boards():
    return ''

 #
-# Extract the current configuration files in the form of a structured schema.
+# Extract the specified configuration files in the form of a structured schema.
 # Contains the full schema for the configuration files, not just the enabled options,
 # Contains the current values of the options, not just data structure, so "schema" is a slight misnomer.
 #
@@ -99,9 +116,9 @@ def load_boards():
 #    - requires = The conditions that must be met for the define to be enabled
 #    - comment  = The comment for the define, if it has one
 #    - units    = The units for the define, if it has one
-#    - options  = The options for the define, if it has one
+#    - options  = The options for the define, if it has any
 #
-def extract():
+def extract_files(filekey):
    # Load board names from boards.h
    boards = load_boards()

@@ -114,23 +131,21 @@ def extract():
        GET_SENSORS     = 4 # Gathering temperature sensor options
        ERROR           = 9 # Syntax error

-    # List of files to process, with shorthand
-    filekey = { 'Configuration.h':'basic', 'Configuration_adv.h':'advanced' }
    # A JSON object to store the data
-    sch_out = { 'basic':{}, 'advanced':{} }
+    sch_out = { key:{} for key in filekey.values() }
    # Regex for #define NAME [VALUE] [COMMENT] with sanitized line
    defgrep = re.compile(r'^(//)?\s*(#define)\s+([A-Za-z0-9_]+)\s*(.*?)\s*(//.+)?$')
    # Pattern to match a float value
-    flt = r'[-+]?\s*(\d+\.|\d*\.\d+)([eE][-+]?\d+)?[fF]?'
-    # Defines to ignore
-    ignore = ('CONFIGURATION_H_VERSION', 'CONFIGURATION_ADV_H_VERSION', 'CONFIG_EXAMPLES_DIR', 'CONFIG_EXPORT')
+    flt = r'[-+]?\s*(?:\d+\.|\d*\.\d+)(?:[eE][-+]?\d+)?[fF]?'
+    # Pattern to match an integer expression
+    int_expr = r'(?:[-+]?\s*\d+(?:\s*[*\/+\-]\s*\d+)*)'
    # Start with unknown state
    state = Parse.NORMAL
    # Serial ID
    sid = 0
    # Loop through files and parse them line by line
    for fn, fk in filekey.items():
-        with Path("Marlin", fn).open() as fileobj:
+        with Path("Marlin", fn).open(encoding='utf-8') as fileobj:
            section = 'none'        # Current Settings section
            line_number = 0         # Counter for the line number of the file
            conditions = []         # Create a condition stack for the current file
@@ -140,7 +155,7 @@ def extract():
            eol_options = False     # The options came from end of line, so only apply once
            join_line = False       # A flag that the line should be joined with the previous one
            line = ''               # A line buffer to handle \ continuation
-            last_added_ref = None   # Reference to the last added item
+            last_added_ref = {}     # Reference to the last added item
            # Loop through the lines in the file
            for the_line in fileobj.readlines():
                line_number += 1
@@ -180,26 +195,42 @@ def extract():
                            cfield = 'notes' if 'comment' in last_added_ref else 'comment'
                            last_added_ref[cfield] = cline

+                #
+                # Add the given comment line to the comment buffer, unless:
+                # - The line starts with ':' and JSON values to assign to 'opt'.
+                # - The line starts with '@section' so a new section needs to be returned.
+                # - The line starts with '======' so just skip it.
+                #
                def use_comment(c, opt, sec, bufref):
-                    if c.startswith(':'):               # If the comment starts with : then it has magic JSON
-                        d = c[1:].strip()               # Strip the leading :
-                        cbr = c.rindex('}') if d.startswith('{') else c.rindex(']') if d.startswith('[') else 0
+                    '''
+                    c       - The comment line to parse
+                    opt     - Options JSON string to return (if not updated)
+                    sec     - Section to return (if not updated)
+                    bufref  - The comment buffer to add to
+                    '''
+                    sc = c.strip()                      # Strip for special patterns
+                    if sc.startswith(':'):              # If the comment starts with : then it has magic JSON
+                        d = sc[1:].strip()              # Strip the leading : and spaces
+                        # Look for a JSON container
+                        cbr = sc.rindex('}') if d.startswith('{') else sc.rindex(']') if d.startswith('[') else 0
                        if cbr:
-                            opt, cmt = c[1:cbr+1].strip(), c[cbr+1:].strip()
+                            opt, cmt = sc[1:cbr+1].strip(), sc[cbr+1:].strip()
                            if cmt != '': bufref.append(cmt)
                        else:
-                            opt = c[1:].strip()
-                    elif c.startswith('@section'):      # Start a new section
-                        sec = c[8:].strip()
-                    elif not c.startswith('========'):
-                        bufref.append(c)
+                            opt = sc[1:].strip()        # Some literal value not in a JSON container?
+                    else:
+                        m = re.match(r'@section\s*(.+)', sc) # Start a new section?
+                        if m:
+                            sec = m[1]
+                        elif not sc.startswith('========'):
+                            bufref.append(c)            # Anything else is part of the comment
                    return opt, sec

                # For slash comments, capture consecutive slash comments.
                # The comment will be applied to the next #define.
                if state == Parse.SLASH_COMMENT:
                    if not defmatch and the_line.startswith('//'):
-                        use_comment(the_line[2:].strip(), options_json, section, comment_buff)
+                        options_json, section = use_comment(the_line[2:].strip(), options_json, section, comment_buff)
                        continue
                    else:
                        state = Parse.NORMAL
@@ -216,17 +247,16 @@ def extract():
                        # Temperature sensors are done
                        if state == Parse.GET_SENSORS:
                            options_json = f'[ {options_json[:-2]} ]'
-
                        state = Parse.NORMAL

-                    # Strip the leading '*' from block comments
+                    # Strip the leading '* ' from block comments
                    cline = re.sub(r'^\* ?', '', cline)

                    # Collect temperature sensors
                    if state == Parse.GET_SENSORS:
-                        sens = re.match(r'^(-?\d+)\s*:\s*(.+)$', cline)
+                        sens = re.match(r'^\s*(-?\d+)\s*:\s*(.+)$', cline)
                        if sens:
-                            s2 = sens[2].replace("'","''")
+                            s2 = sens[2].replace("'", "''")
                            options_json += f"{sens[1]}:'{sens[1]} - {s2}', "

                    elif state == Parse.BLOCK_COMMENT:
@@ -251,12 +281,11 @@ def extract():
                        comment_buff = []
                        state = Parse.BLOCK_COMMENT
                        eol_options = False
-
                    elif cpos2 != -1 and (cpos2 < cpos1 or cpos1 == -1):
                        cpos = cpos2

                        # Comment after a define may be continued on the following lines
-                        if defmatch != None and cpos > 10:
+                        if defmatch is not None and cpos > 10:
                            state = Parse.EOL_COMMENT
                            prev_comment = '\n'.join(comment_buff)
                            comment_buff = []
@@ -286,9 +315,11 @@ def extract():

                    # Parenthesize the given expression if needed
                    def atomize(s):
-                        if s == '' \
-                        or re.match(r'^[A-Za-z0-9_]*(\([^)]+\))?$', s) \
-                        or re.match(r'^[A-Za-z0-9_]+ == \d+?$', s):
+                        s = s.strip()
+                        if not s or s.isidentifier() or (s.startswith('(') and s.endswith(')')):
+                            return s
+                        if re.match(r'^[A-Za-z0-9_]*(\([^)]+\))$', s) \
+                        or re.match(r'^[A-Za-z0-9_]+\s*[=!<>]=?\s*.*$', s):
                            return s
                        return f'({s})'

@@ -323,10 +354,10 @@ def extract():
                        conditions.append([ f'!defined({line[7:].strip()})' ])

                    # Handle a complete #define line
-                    elif defmatch != None:
+                    elif defmatch is not None:

                        # Get the match groups into vars
-                        enabled, define_name, val = defmatch[1] == None, defmatch[3], defmatch[4]
+                        enabled, define_name, val = defmatch[1] is None, defmatch[3], defmatch[4]

                        # Increment the serial ID
                        sid += 1
@@ -341,27 +372,30 @@ def extract():
                        }

                        # Type is based on the value
-                        value_type = \
-                             'switch'  if val == '' \
-                        else 'bool'    if re.match(r'^(true|false)$', val) \
-                        else 'int'     if re.match(r'^[-+]?\s*\d+$', val) \
-                        else 'ints'    if re.match(r'^([-+]?\s*\d+)(\s*,\s*[-+]?\s*\d+)+$', val) \
-                        else 'floats'  if re.match(rf'({flt}(\s*,\s*{flt})+)', val) \
-                        else 'float'   if re.match(f'^({flt})$', val) \
-                        else 'string'  if val[0] == '"' \
-                        else 'char'    if val[0] == "'" \
-                        else 'state'   if re.match(r'^(LOW|HIGH)$', val) \
-                        else 'enum'    if re.match(r'^[A-Za-z0-9_]{3,}$', val) \
-                        else 'int[]'   if re.match(r'^{\s*[-+]?\s*\d+(\s*,\s*[-+]?\s*\d+)*\s*}$', val) \
-                        else 'float[]' if re.match(r'^{{\s*{flt}(\s*,\s*{flt})*\s*}}$', val) \
-                        else 'array'   if val[0] == '{' \
-                        else ''
+                        value_type = (
+                                 'switch'  if val == ''
+                            else 'int'     if re.match(r'^[-+]?\s*\d+$', val)
+                            else 'ints'    if re.match(r'^[-+]?\s*\d+(?:\s*,\s*[-+]?\s*\d+)+$', val)
+                            else 'floats'  if re.match(rf"^{flt}(?:\s*,\s*{flt})+$", val)
+                            else 'float'   if re.match(rf"^{flt}$", val)
+                            else 'string'  if val.startswith('"')
+                            else 'char'    if val.startswith("'")
+                            else 'bool'    if val in ('true', 'false')
+                            else 'state'   if val in ('HIGH', 'LOW')
+                            else 'int[]'   if re.match(rf"^\{{\s*{int_expr}(?:\s*,\s*{int_expr})*\s*\}}$", val)
+                            else 'float[]' if re.match(rf"^\{{\s*{flt}(?:\s*,\s*{flt})*\s*\}}$", val)
+                            else 'array'   if val.startswith('{')
+                            else 'enum'    if re.match(r'^[A-Za-z0-9_]{3,}$', val)
+                            else ''
+                        )

-                        val = (val == 'true')           if value_type == 'bool' \
-                        else int(val)                   if value_type == 'int' \
-                        else val.replace('f','')        if value_type == 'floats' \
-                        else float(val.replace('f','')) if value_type == 'float' \
-                        else val
+                        val = (
+                                 (val == 'true')            if value_type == 'bool'
+                            else int(val)                   if value_type == 'int'
+                            else val.replace('f','')        if value_type == 'floats'
+                            else float(val.replace('f','')) if value_type == 'float'
+                            else val
+                        )

                        if val != '': define_info['value'] = val
                        if value_type != '': define_info['type'] = value_type
@@ -371,7 +405,7 @@ def extract():

                        # If the comment_buff is not empty, add the comment to the info
                        if comment_buff:
-                            full_comment = '\n'.join(comment_buff)
+                            full_comment = '\n'.join(comment_buff).strip()

                            # An EOL comment will be added later
                            # The handling could go here instead of above
@@ -385,9 +419,17 @@ def extract():
                            units = re.match(r'^\(([^)]+)\)', full_comment)
                            if units:
                                units = units[1]
-                                if units == 's' or units == 'sec': units = 'seconds'
+                                if units in ('s', 'sec'): units = 'seconds'
                                define_info['units'] = units

+                        if 'comment' not in define_info or define_info['comment'] == '':
+                            if prev_comment:
+                                define_info['comment'] = prev_comment
+                                prev_comment = ''
+
+                        if 'comment' in define_info and define_info['comment'] == '':
+                            del define_info['comment']
+
                        # Set the options for the current #define
                        if define_name == "MOTHERBOARD" and boards != '':
                            define_info['options'] = boards
@@ -412,13 +454,31 @@ def extract():

    return sch_out

+#
+# Extract the current configuration files in the form of a structured schema.
+#
+def extract():
+    # List of files to process, with shorthand
+    return extract_files({ 'Configuration.h':'basic', 'Configuration_adv.h':'advanced' })
+
 def dump_json(schema:dict, jpath:Path):
-    with jpath.open('w') as jfile:
+    with jpath.open('w', encoding='utf-8') as jfile:
        json.dump(schema, jfile, ensure_ascii=False, indent=2)

 def dump_yaml(schema:dict, ypath:Path):
    import yaml
-    with ypath.open('w') as yfile:
+
+    # Custom representer for all multi-line strings
+    def str_literal_representer(dumper, data):
+        if '\n' in data:  # Check for multi-line strings
+            # Add a newline to trigger '|+'
+            if not data.endswith('\n'): data += '\n'
+            return dumper.represent_scalar('tag:yaml.org,2002:str', data, style='|')
+        return dumper.represent_scalar('tag:yaml.org,2002:str', data)
+
+    yaml.add_representer(str, str_literal_representer)
+
+    with ypath.open('w', encoding='utf-8') as yfile:
        yaml.dump(schema, yfile, default_flow_style=False, width=120, indent=2)

 def main():
@@ -439,12 +499,17 @@ def main():
        def inargs(c): return len(set(args) & set(c)) > 0

        # Help / Unknown option
-        unk = not inargs(['some','json','jsons','group','yml','yaml'])
+        unk = not inargs(['some','json','jsons','group','yml','yaml', '-h', '--help'])
        if (unk): print(f"Unknown option: '{args[0]}'")
        if inargs(['-h', '--help']) or unk:
-            print("Usage: schema.py [some|json|jsons|group|yml|yaml]...")
-            print("       some  = json + yml")
-            print("       jsons = json + group")
+            print("Extract firmware configuration into structured JSON or YAML schema format.")
+            print("Usage: schema.py [-h] [some|json|jsons|group|yml|yaml]")
+            print("  some    Generate both JSON and YAML output (schema.json and schema.yml)")
+            print("  json    Generate JSON output (schema.json)")
+            print("  jsons   Generate grouped JSON output with wildcard options (schema.json and schema_grouped.json)")
+            print("  group   Generate grouped JSON output only (schema_grouped.json)")
+            print("  yml     Generate YAML output (schema.yml)")
+            print("  yaml    Same as 'yml'")
            return

        # JSON schema
--- a/buildroot/share/PlatformIO/scripts/signature.py
+++ b/buildroot/share/PlatformIO/scripts/signature.py
@@ -2,11 +2,10 @@
 #
 # signature.py
 #
-import schema
-
-import subprocess,re,json,hashlib
+import schema, subprocess, re, json, hashlib
 from datetime import datetime
 from pathlib import Path
+from functools import reduce

 def enabled_defines(filepath):
    '''
@@ -35,18 +34,29 @@ def enabled_defines(filepath):
    '''
    outdict = {}
    section = "user"
-    spatt = re.compile(r".*@section +([-a-zA-Z0-9_\s]+)$") # must match @section ...
+    spatt = re.compile(r".*@section +([-a-zA-Z0-9_\s]+)$") # @section ...
+
+    if not Path(filepath).is_file(): return outdict

    f = open(filepath, encoding="utf8").read().split("\n")

-    # Get the full contents of the file and remove all block comments.
-    # This will avoid false positives from #defines in comments
-    f = re.sub(r'/\*.*?\*/', '', '\n'.join(f), flags=re.DOTALL).split("\n")
-
+    incomment = False
    for line in f:
        sline = line.strip()
+
        m = re.match(spatt, sline) # @section ...
        if m: section = m.group(1).strip() ; continue
+
+        if incomment:
+            if '*/' in sline:
+                incomment = False
+            continue
+        else:
+            mpos, spos = sline.find('/*'), sline.find('//')
+            if mpos >= 0 and (spos < 0 or spos > mpos):
+                incomment = True
+                continue
+
        if sline[:7] == "#define":
            # Extract the key here (we don't care about the value)
            kv = sline[8:].strip().split()
@@ -56,9 +66,10 @@ def enabled_defines(filepath):
 # Compute the SHA256 hash of a file
 def get_file_sha256sum(filepath):
    sha256_hash = hashlib.sha256()
-    with open(filepath,"rb") as f:
+    if not Path(filepath).is_file(): return ""
+    with open(filepath, "rb") as f:
        # Read and update hash string value in blocks of 4K
-        for byte_block in iter(lambda: f.read(4096),b""):
+        for byte_block in iter(lambda: f.read(4096), b""):
            sha256_hash.update(byte_block)
    return sha256_hash.hexdigest()

@@ -67,9 +78,14 @@ def get_file_sha256sum(filepath):
 #
 import zipfile
 def compress_file(filepath, storedname, outpath):
-    with zipfile.ZipFile(outpath, 'w', compression=zipfile.ZIP_BZIP2, compresslevel=9) as zipf:
-        zipf.write(filepath, arcname=storedname, compress_type=zipfile.ZIP_BZIP2, compresslevel=9)
+    with zipfile.ZipFile(outpath, 'w', compression=zipfile.ZIP_DEFLATED, allowZip64=False, compresslevel=9) as zipf:
+        zipf.write(filepath, arcname=storedname)

+ignore = ('CONFIGURATION_H_VERSION', 'CONFIGURATION_ADV_H_VERSION', 'CONFIG_EXAMPLES_DIR', 'CONFIG_EXPORT')
+
+#
+# Compute a build signature and/or export the configuration
+#
 def compute_build_signature(env):
    '''
    Compute the build signature by extracting all configuration settings and
@@ -81,11 +97,17 @@ def compute_build_signature(env):
    env.Append(BUILD_SIGNATURE=1)

    build_path = Path(env['PROJECT_BUILD_DIR'], env['PIOENV'])
-    marlin_json = build_path / 'marlin_config.json'
+    json_name = 'marlin_config.json'
+    marlin_json = build_path / json_name
    marlin_zip = build_path / 'mc.zip'

+    # ANSI colors
+    green = "\u001b[32m"
+    yellow = "\u001b[33m"
+    red = "\u001b[31m"
+
    # Definitions from these files will be kept
-    header_paths = [ 'Marlin/Configuration.h', 'Marlin/Configuration_adv.h' ]
+    header_paths = ('Marlin/Configuration.h', 'Marlin/Configuration_adv.h')

    # Check if we can skip processing
    hashes = ''
@@ -100,7 +122,7 @@ def compute_build_signature(env):
            conf = json.load(infile)
            same_hash = conf['__INITIAL_HASH'] == hashes
            if same_hash:
-                compress_file(marlin_json, 'marlin_config.json', marlin_zip)
+                compress_file(marlin_json, json_name, marlin_zip)
    except:
        pass

@@ -142,7 +164,8 @@ def compute_build_signature(env):
    #
    # Continue to gather data for CONFIGURATION_EMBEDDING or CONFIG_EXPORT
    #
-    if not ('CONFIGURATION_EMBEDDING' in build_defines or 'CONFIG_EXPORT' in build_defines):
+    is_embed = 'CONFIGURATION_EMBEDDING' in build_defines
+    if not (is_embed or 'CONFIG_EXPORT' in build_defines):
        return

    # Filter out useless macros from the output
@@ -175,29 +198,60 @@ def compute_build_signature(env):

    # Get the CONFIG_EXPORT value and do an extended dump if > 100
    # For example, CONFIG_EXPORT 102 will make a 'config.ini' with a [config:] group for each schema @section
-    config_dump = tryint('CONFIG_EXPORT')
+    config_dump = 1 if is_embed else tryint('CONFIG_EXPORT')
    extended_dump = config_dump > 100
-    if extended_dump: config_dump -= 100
+    config_dump %= 100
+
+    # Get the schema class for exports that require it
+    if config_dump in (3, 4) or (extended_dump and config_dump in (2, 5)):
+        try:
+            conf_schema = schema.extract()
+        except Exception as exc:
+            print(red + "Error: " + str(exc))
+            conf_schema = None
+
+    optorder = ('MOTHERBOARD','SERIAL_PORT','BAUDRATE','USE_WATCHDOG','THERMAL_PROTECTION_HOTENDS','THERMAL_PROTECTION_HYSTERESIS','THERMAL_PROTECTION_PERIOD','BUFSIZE','BLOCK_BUFFER_SIZE','MAX_CMD_SIZE','EXTRUDERS','TEMP_SENSOR_0','TEMP_HYSTERESIS','HEATER_0_MINTEMP','HEATER_0_MAXTEMP','PREHEAT_1_TEMP_HOTEND','BANG_MAX','PIDTEMP','PID_K1','PID_MAX','PID_FUNCTIONAL_RANGE','DEFAULT_KP','DEFAULT_KI','DEFAULT_KD','X_DRIVER_TYPE','Y_DRIVER_TYPE','Z_DRIVER_TYPE','E0_DRIVER_TYPE','X_BED_SIZE','X_MIN_POS','X_MAX_POS','Y_BED_SIZE','Y_MIN_POS','Y_MAX_POS','Z_MIN_POS','Z_MAX_POS','X_HOME_DIR','Y_HOME_DIR','Z_HOME_DIR','X_MIN_ENDSTOP_HIT_STATE','Y_MIN_ENDSTOP_HIT_STATE','Z_MIN_ENDSTOP_HIT_STATE','DEFAULT_AXIS_STEPS_PER_UNIT','AXIS_RELATIVE_MODES','DEFAULT_MAX_FEEDRATE','DEFAULT_MAX_ACCELERATION','HOMING_FEEDRATE_MM_M','HOMING_BUMP_DIVISOR','X_ENABLE_ON','Y_ENABLE_ON','Z_ENABLE_ON','E_ENABLE_ON','INVERT_X_DIR','INVERT_Y_DIR','INVERT_Z_DIR','INVERT_E0_DIR','STEP_STATE_E','STEP_STATE_X','STEP_STATE_Y','STEP_STATE_Z','DISABLE_X','DISABLE_Y','DISABLE_Z','DISABLE_E','PROPORTIONAL_FONT_RATIO','DEFAULT_NOMINAL_FILAMENT_DIA','JUNCTION_DEVIATION_MM','DEFAULT_ACCELERATION','DEFAULT_TRAVEL_ACCELERATION','DEFAULT_RETRACT_ACCELERATION','DEFAULT_MINIMUMFEEDRATE','DEFAULT_MINTRAVELFEEDRATE','MINIMUM_PLANNER_SPEED','MIN_STEPS_PER_SEGMENT','DEFAULT_MINSEGMENTTIME','BED_OVERSHOOT','BUSY_WHILE_HEATING','DEFAULT_EJERK','DEFAULT_KEEPALIVE_INTERVAL','DEFAULT_LEVELING_FADE_HEIGHT','DISABLE_OTHER_EXTRUDERS','DISPLAY_CHARSET_HD44780','EEPROM_BOOT_SILENT','EEPROM_CHITCHAT','ENDSTOPPULLUPS','EXTRUDE_MAXLENGTH','EXTRUDE_MINTEMP','HOST_KEEPALIVE_FEATURE','HOTEND_OVERSHOOT','JD_HANDLE_SMALL_SEGMENTS','LCD_INFO_SCREEN_STYLE','LCD_LANGUAGE','MAX_BED_POWER','MESH_INSET','MIN_SOFTWARE_ENDSTOPS','MAX_SOFTWARE_ENDSTOPS','MIN_SOFTWARE_ENDSTOP_X','MIN_SOFTWARE_ENDSTOP_Y','MIN_SOFTWARE_ENDSTOP_Z','MAX_SOFTWARE_ENDSTOP_X','MAX_SOFTWARE_ENDSTOP_Y','MAX_SOFTWARE_ENDSTOP_Z','PREHEAT_1_FAN_SPEED','PREHEAT_1_LABEL','PREHEAT_1_TEMP_BED','PREVENT_COLD_EXTRUSION','PREVENT_LENGTHY_EXTRUDE','PRINTJOB_TIMER_AUTOSTART','PROBING_MARGIN','SHOW_BOOTSCREEN','SOFT_PWM_SCALE','STRING_CONFIG_H_AUTHOR','TEMP_BED_HYSTERESIS','TEMP_BED_RESIDENCY_TIME','TEMP_BED_WINDOW','TEMP_RESIDENCY_TIME','TEMP_WINDOW','VALIDATE_HOMING_ENDSTOPS','XY_PROBE_FEEDRATE','Z_CLEARANCE_BETWEEN_PROBES','Z_CLEARANCE_DEPLOY_PROBE','Z_CLEARANCE_MULTI_PROBE','ARC_SUPPORT','AUTO_REPORT_TEMPERATURES','AUTOTEMP','AUTOTEMP_OLDWEIGHT','BED_CHECK_INTERVAL','DEFAULT_STEPPER_TIMEOUT_SEC','DEFAULT_VOLUMETRIC_EXTRUDER_LIMIT','DISABLE_IDLE_X','DISABLE_IDLE_Y','DISABLE_IDLE_Z','DISABLE_IDLE_E','E0_AUTO_FAN_PIN','ENCODER_100X_STEPS_PER_SEC','ENCODER_10X_STEPS_PER_SEC','ENCODER_RATE_MULTIPLIER','EXTENDED_CAPABILITIES_REPORT','EXTRUDER_AUTO_FAN_SPEED','EXTRUDER_AUTO_FAN_TEMPERATURE','FANMUX0_PIN','FANMUX1_PIN','FANMUX2_PIN','FASTER_GCODE_PARSER','HOMING_BUMP_MM','MAX_ARC_SEGMENT_MM','MIN_ARC_SEGMENT_MM','MIN_CIRCLE_SEGMENTS','N_ARC_CORRECTION','SERIAL_OVERRUN_PROTECTION','SLOWDOWN','SLOWDOWN_DIVISOR','TEMP_SENSOR_BED','THERMAL_PROTECTION_BED_HYSTERESIS','THERMOCOUPLE_MAX_ERRORS','TX_BUFFER_SIZE','WATCH_BED_TEMP_INCREASE','WATCH_BED_TEMP_PERIOD','WATCH_TEMP_INCREASE','WATCH_TEMP_PERIOD')
+
+    def optsort(x, optorder):
+        return optorder.index(x) if x in optorder else float('inf')

    #
-    # Produce an INI file if CONFIG_EXPORT == 2
+    # CONFIG_EXPORT 102 = config.ini, 105 = Config.h
+    # Get sections using the schema class
+    #
+    if extended_dump and config_dump in (2, 5):
+        if not conf_schema: exit(1)
+
+        # Start with a preferred @section ordering
+        preorder = ('test','custom','info','machine','eeprom','stepper drivers','multi stepper','idex','extruder','geometry','homing','kinematics','motion','motion control','endstops','filament runout sensors','probe type','probes','bltouch','leveling','temperature','hotend temp','mpctemp','pid temp','mpc temp','bed temp','chamber temp','fans','tool change','advanced pause','calibrate','calibration','media','lcd','lights','caselight','interface','custom main menu','custom config menu','custom buttons','develop','debug matrix','delta','scara','tpara','polar','polargraph','cnc','nozzle park','nozzle clean','gcode','serial','host','filament width','i2c encoders','i2cbus','joystick','multi-material','nanodlp','network','photo','power','psu control','reporting','safety','security','servos','stats','tmc/config','tmc/hybrid','tmc/serial','tmc/smart','tmc/spi','tmc/stallguard','tmc/status','tmc/stealthchop','tmc/tmc26x','units','volumetrics','extras')
+
+        sections = { key:{} for key in preorder }
+
+        # Group options by schema @section
+        for header in real_config:
+            for name in real_config[header]:
+                #print(f"  name: {name}")
+                if name in ignore: continue
+                ddict = real_config[header][name]
+                #print(f"   real_config[{header}][{name}]:", ddict)
+                sect = ddict['section']
+                if sect not in sections: sections[sect] = {}
+                sections[sect][name] = ddict
+
+    #
+    # CONFIG_EXPORT 2 or 102 = config.ini
    #
    if config_dump == 2:
-        print("Generating config.ini ...")
+        print(yellow + "Generating config.ini ...")

        ini_fmt = '{0:40} = {1}'
        ext_fmt = '{0:40}   {1}'
-        ignore = ('CONFIGURATION_H_VERSION', 'CONFIGURATION_ADV_H_VERSION', 'CONFIG_EXAMPLES_DIR', 'CONFIG_EXPORT')

        if extended_dump:
            # Extended export will dump config options by section

            # We'll use Schema class to get the sections
-            try:
-                conf_schema = schema.extract()
-            except Exception as exc:
-                print("Error: " + str(exc))
-                exit(1)
+            if not conf_schema: exit(1)

            # Then group options by schema @section
            sections = {}
@@ -230,7 +284,7 @@ def compute_build_signature(env):
        for line in sec_lines[1:]: sec_list += '\n' + ext_fmt.format('', line)

        config_ini = build_path / 'config.ini'
-        with config_ini.open('w') as outfile:
+        with config_ini.open('w', encoding='utf-8', newline='') as outfile:
            filegrp = { 'Configuration.h':'config:basic', 'Configuration_adv.h':'config:advanced' }
            vers = build_defines["CONFIGURATION_H_VERSION"]
            dt_string = datetime.now().strftime("%Y-%m-%d at %H:%M:%S")
@@ -293,7 +347,9 @@ f'''#
                    sani = re.sub(r'[- ]+', '_', skey).lower()
                    outfile.write(f"\n[config:{sani}]\n")
                    opts = sections[skey]
-                    for name in sorted(opts):
+                    opts_keys = sorted(opts.keys(), key=lambda x: optsort(x, optorder))
+                    for name in opts_keys:
+                        if name in ignore: continue
                        val = opts[name]['value']
                        if val == '': val = 'on'
                        #print(f"  {name} = {val}")
@@ -304,28 +360,76 @@ f'''#
                # Standard export just dumps config:basic and config:advanced sections
                for header in real_config:
                    outfile.write(f'\n[{filegrp[header]}]\n')
-                    for name in sorted(real_config[header]):
-                        if name not in ignore:
-                            val = real_config[header][name]['value']
-                            if val == '': val = 'on'
-                            outfile.write(ini_fmt.format(name.lower(), val) + '\n')
+                    opts = real_config[header]
+                    opts_keys = sorted(opts.keys(), key=lambda x: optsort(x, optorder))
+                    for name in opts_keys:
+                        if name in ignore: continue
+                        val = opts[name]['value']
+                        if val == '': val = 'on'
+                        outfile.write(ini_fmt.format(name.lower(), val) + '\n')

    #
-    # CONFIG_EXPORT 3 = schema.json, 4 = schema.yml
+    # CONFIG_EXPORT 5 or 105 = Config.h
    #
-    if config_dump >= 3:
-        try:
-            conf_schema = schema.extract()
-        except Exception as exc:
-            print("Error: " + str(exc))
-            conf_schema = None
+    if config_dump == 5:
+        print(yellow + "Generating Config-export.h ...")
+
+        config_h = Path('Marlin', 'Config-export.h')
+        with config_h.open('w') as outfile:
+            filegrp = { 'Configuration.h':'config:basic', 'Configuration_adv.h':'config:advanced' }
+            vers = build_defines["CONFIGURATION_H_VERSION"]
+            dt_string = datetime.utcnow().strftime("%Y-%m-%d at %H:%M:%S")
+
+            out_text = f'''/**
+ * Config.h - Marlin Firmware distilled configuration
+ * Usage: Place this file in the 'Marlin' folder with the name 'Config.h'.
+ *
+ * Exported by Marlin build on {dt_string}.
+ */
+'''
+
+            subs = (('Bltouch','BLTouch'),('hchop','hChop'),('Eeprom','EEPROM'),('Gcode','G-code'),('lguard','lGuard'),('Idex','IDEX'),('Lcd','LCD'),('Mpc','MPC'),('Pid','PID'),('Psu','PSU'),('Scara','SCARA'),('Spi','SPI'),('Tmc','TMC'),('Tpara','TPARA'))
+            define_fmt = '#define {0:40} {1}'
+            if extended_dump:
+                # Loop through the sections
+                for skey in sections:
+                    #print(f"  skey: {skey}")
+                    opts = sections[skey]
+                    headed = False
+                    opts_keys = sorted(opts.keys(), key=lambda x: optsort(x, optorder))
+                    for name in opts_keys:
+                        if name in ignore: continue
+                        val = opts[name]['value']
+                        if not headed:
+                            head = reduce(lambda s, r: s.replace(*r), subs, skey.title())
+                            out_text += f"\n//\n// {head}\n//\n"
+                            headed = True
+                        out_text += define_fmt.format(name, val).strip() + '\n'
+
+            else:
+                # Dump config options in just two sections, by file
+                for header in real_config:
+                    out_text += f'\n/**\n * Overrides for {header}\n */\n'
+                    opts = real_config[header]
+                    opts_keys = sorted(opts.keys(), key=lambda x: optsort(x, optorder))
+                    for name in opts_keys:
+                        if name in ignore: continue
+                        val = opts[name]['value']
+                        out_text += define_fmt.format(name, val).strip() + '\n'
+
+            outfile.write(out_text)
+
+    #
+    # CONFIG_EXPORT 3 = schema.json, 13 = schema_grouped.json, 4 = schema.yml
+    #
+    if config_dump in (3, 4, 13):

        if conf_schema:
            #
            # 3 = schema.json
            #
            if config_dump in (3, 13):
-                print("Generating schema.json ...")
+                print(yellow + "Generating schema.json ...")
                schema.dump_json(conf_schema, build_path / 'schema.json')
                if config_dump == 13:
                    schema.group_options(conf_schema)
@@ -335,7 +439,7 @@ f'''#
            # 4 = schema.yml
            #
            elif config_dump == 4:
-                print("Generating schema.yml ...")
+                print(yellow + "Generating schema.yml ...")
                try:
                    import yaml
                except ImportError:
@@ -347,19 +451,20 @@ f'''#
                schema.dump_yaml(conf_schema, build_path / 'schema.yml')

    #
-    # Produce a JSON file for CONFIGURATION_EMBEDDING or CONFIG_EXPORT == 1
+    # Produce a JSON file for CONFIGURATION_EMBEDDING or CONFIG_EXPORT == 1 or 101
    # Skip if an identical JSON file was already present.
    #
-    if not same_hash and (config_dump == 1 or 'CONFIGURATION_EMBEDDING' in build_defines):
+    if not same_hash and config_dump == 1:
        with marlin_json.open('w') as outfile:

            json_data = {}
            if extended_dump:
-                print("Extended dump ...")
+                print(yellow + "Extended dump ...")
                for header in real_config:
                    confs = real_config[header]
                    json_data[header] = {}
                    for name in confs:
+                        if name in ignore: continue
                        c = confs[name]
                        s = c['section']
                        if s not in json_data[header]: json_data[header][s] = {}
@@ -369,6 +474,7 @@ f'''#
                    conf = real_config[header]
                    #print(f"real_config[{header}]", conf)
                    for name in conf:
+                        if name in ignore: continue
                        json_data[name] = conf[name]['value']

            json_data['__INITIAL_HASH'] = hashes
@@ -389,13 +495,13 @@ f'''#
    #
    # The rest only applies to CONFIGURATION_EMBEDDING
    #
-    if not 'CONFIGURATION_EMBEDDING' in build_defines:
+    if not is_embed:
        (build_path / 'mc.zip').unlink(missing_ok=True)
        return

    # Compress the JSON file as much as we can
    if not same_hash:
-        compress_file(marlin_json, 'marlin_config.json', marlin_zip)
+        compress_file(marlin_json, json_name, marlin_zip)

    # Generate a C source file containing the entire ZIP file as an array
    with open('Marlin/src/mczip.h','wb') as result_file:
@@ -415,5 +521,12 @@ f'''#

 if __name__ == "__main__":
    # Build required. From command line just explain usage.
-    print("Use schema.py to export JSON and YAML from the command-line.")
-    print("Build Marlin with CONFIG_EXPORT 2 to export 'config.ini'.")
+    print("*** THIS SCRIPT USED BY common-dependencies.py ***\n\n"
+        + "Current options for config and schema export:\n"
+        + " - marlin_config.json  : Build Marlin with CONFIG_EXPORT 1 or 101. (Use CONFIGURATION_EMBEDDING for 'mc.zip')\n"
+        + " - config.ini          : Build Marlin with CONFIG_EXPORT 2 or 102.\n"
+        + " - schema.json         : Run 'schema.py json' (CONFIG_EXPORT 3).\n"
+        + " - schema_grouped.json : Run 'schema.py group' (CONFIG_EXPORT 13).\n"
+        + " - schema.yml          : Run 'schema.py yml' (CONFIG_EXPORT 4).\n"
+        + " - Config-export.h     : Build Marlin with CONFIG_EXPORT 5 or 105.\n"
+    )
--- a/buildroot/share/fonts/buildhzk.py
+++ b/buildroot/share/fonts/buildhzk.py
@@ -4,8 +4,7 @@
 # Author: Taylor Talkington
 # License: GPL

-import bdflib.reader
-import math
+import bdflib.reader, math

 def glyph_bits(size_x, size_y, font, glyph_ord):
    asc = font[b'FONT_ASCENT']
--- a/buildroot/share/git/mfhelp
+++ b/buildroot/share/git/mfhelp
@@ -12,6 +12,7 @@ Marlin Firmware Commands:
  mfadd ....... Fetch a remote branch from any Marlin fork
  mfclean ..... Attempt to clean up merged and deleted branches
  mfdoc ....... Build the website, serve locally, and browse
+  mfenvs ...... Get current board SHORT_NAME (###): [ env1 env2 ... ]
  mffp ........ Push new commits directly to MarlinFirmware
  mfinfo ...... Provide branch information (for the other scripts)
  mfinit ...... Create an 'upstream' remote for 'MarlinFirmare'
--- a/buildroot/share/scripts/MarlinBinaryProtocol.py
+++ b/buildroot/share/scripts/MarlinBinaryProtocol.py
@@ -2,14 +2,9 @@
 # MarlinBinaryProtocol.py
 # Supporting Firmware upload via USB/Serial, saving to the attached media.
 #
-import serial
-import math
-import time
+import serial, math, time, threading, sys, datetime, random
 from collections import deque
-import threading
-import sys
-import datetime
-import random
+
 try:
    import heatshrink2 as heatshrink
    heatshrink_exists = True
--- a/buildroot/share/scripts/createTemperatureLookupMarlin.py
+++ b/buildroot/share/scripts/createTemperatureLookupMarlin.py
@@ -18,8 +18,7 @@ Options:
  --num-temps=...   the number of temperature points to calculate (default: 36)
 """

-from __future__ import print_function
-from __future__ import division
+from __future__ import print_function, division

 from math import *
 import sys, getopt
--- a/buildroot/share/scripts/rle16_compress_cpp_image_data.py
+++ b/buildroot/share/scripts/rle16_compress_cpp_image_data.py
@@ -5,8 +5,7 @@
 #
 # Usage: rle16_compress_cpp_image_data.py INPUT_FILE.cpp OUTPUT_FILE.cpp
 #
-import sys,struct
-import re
+import sys, struct, re

 def addCompressedData(input_file, output_file):
    ofile = open(output_file, 'wt')
--- a/buildroot/share/scripts/rle_compress_bitmap.py
+++ b/buildroot/share/scripts/rle_compress_bitmap.py
@@ -6,10 +6,11 @@
 #
 # Usage: rle_compress_bitmap.py INPUT_FILE OUTPUT_FILE
 #
-import sys,struct
-import re
+import sys, struct, re

 def addCompressedData(input_file, output_file):
+    input_lines = input_file.readlines()
+    input_file.close()
    ofile = open(output_file, 'wt')

    datatype = "uint8_t"
@@ -18,8 +19,7 @@ def addCompressedData(input_file, output_file):
    arrname = ''

    c_data_section = False ; c_skip_data = False ; c_footer = False
-    while True:
-        line = input_file.readline()
+    for line in input_lines:
        if not line: break

        if not c_footer:
@@ -56,8 +56,6 @@ def addCompressedData(input_file, output_file):
                arrname = line.split('[')[0].split(' ')[-1]
                print("Found data array", arrname)

-    input_file.close()
-
    #print("\nRaw Bitmap Data", raw_data)

    #
@@ -190,11 +188,11 @@ if len(sys.argv) <= 2:
    print('Usage: rle_compress_bitmap.py INPUT_FILE OUTPUT_FILE')
    exit(1)

-output_cpp = sys.argv[2]
+output_h = sys.argv[2]
 inname = sys.argv[1].replace('//', '/')
 try:
-    input_cpp = open(inname)
+    input_h = open(inname)
    print("Processing", inname, "...")
-    addCompressedData(input_cpp, output_cpp)
+    addCompressedData(input_h, output_h)
 except OSError:
    print("Can't find input file", inname)
--- a/buildroot/share/sublime/auto_build_sublime_menu/000_read_me.txt
+++ b/buildroot/share/sublime/auto_build_sublime_menu/000_read_me.txt
@@ -1,40 +0,0 @@
-Overview:
-1) Install Sublime
-2) Install Deviot  (?optional?)
-3) Install WebDevShell (this will execute the auto-build script)
-4) Copy the menu configuration to the proper Sublime directory
-5) Add platformio to your path (usually not needed)
-
-
-Sublime with autobuild
-  Tools
-    Install Package Control
-  Tools
-    Command Palette
-      Package Control: Install Package
-          type in deviot and click on it
-  Tools
-    Command Palette
-      Package Control: Install Package
-          type in WebDevShell and click on it
-
-  in Sublime, open Marlin directory with "platformio.ini" in it
-
-  starting in the top level directory, go to the folder "Buildroot/shared/Sublime"
-    copy the folder "auto_build_sublime_menu" and contents to:
-      Windows
-       \Users\your_user_name\AppData\Roaming\Sublime Text 3\Packages
-      Linux
-        /home/your_user_name/.config/sublime-text-3/Packages/User
-      macOS (Click on the Finder's 'Go' menu and hold down Option to open...)
-        ~/Library/Application Support/Sublime Text 3/Packages/User
-
-The menu should now be visible
-
-If you get an error message that says "file not found" and  "subprocess.Popen(['platformio' ... "
-then you'll need to add platformio to your path.
-  macOS
-      sudo nano /etc/paths
-        add these to the bottom
-            /Users/bob/.platformio
-            /Users/bob/.platformio/penv/bin
--- a/buildroot/share/sublime/auto_build_sublime_menu/Main.sublime-menu
+++ b/buildroot/share/sublime/auto_build_sublime_menu/Main.sublime-menu
@@ -1,66 +0,0 @@
-[
-
-    {
-        "caption": "Auto Build",
-        "children": [
-            {
-                "caption": "PIO Build",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py build"
-                }
-            },
-            {
-                "caption": "PIO Clean",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py clean"
-                }
-            },
-            {
-                "caption": "PIO Upload",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py upload"
-                }
-            },
-            {
-                "caption": "PIO Upload (traceback)",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py traceback"
-                }
-            },
-            {
-                "caption": "PIO Upload using Programmer",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py program"
-                }
-            },
-            {
-                "caption": "PIO Test",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py test"
-                }
-            },
-            {
-                "caption": "PIO Debug",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py debug"
-                }
-            },
-            {
-                "caption": "PIO Remote",
-                "command": "webdevshell",
-                "args": {
-                    "command": "python buildroot/share/vscode/auto_build.py remote"
-                }
-            }
-        ],
-        "id": "AutoBuild",
-        "mnemonic": "A"
-    }
-]
--- a/buildroot/share/vscode/auto_build.py
+++ b/buildroot/share/vscode/auto_build.py
--- a/buildroot/share/vscode/avrdude.conf
+++ b/buildroot/share/vscode/avrdude.conf
--- a/buildroot/share/vscode/avrdude_5.10_linux
+++ b/buildroot/share/vscode/avrdude_5.10_linux
--- a/buildroot/share/vscode/avrdude_5.10_macOS
+++ b/buildroot/share/vscode/avrdude_5.10_macOS
--- a/buildroot/share/vscode/avrdude_linux.conf
+++ b/buildroot/share/vscode/avrdude_linux.conf
--- a/buildroot/share/vscode/avrdude_macOS.conf
+++ b/buildroot/share/vscode/avrdude_macOS.conf
--- a/buildroot/share/vscode/create_custom_upload_command_CDC.py
+++ b/buildroot/share/vscode/create_custom_upload_command_CDC.py
@@ -1,143 +0,0 @@
-#!/usr/bin/env python
-#
-#  Builds custom upload command
-#    1) Run platformio as a subprocess to find a COM port
-#    2) Build the upload command
-#    3) Exit and let upload tool do the work
-#
-#  This script runs between completion of the library/dependencies installation and compilation.
-#
-#  Will continue on if a COM port isn't found so that the compilation can be done.
-#
-
-from __future__ import print_function
-from __future__ import division
-
-import subprocess, os, platform
-from SCons.Script import DefaultEnvironment
-
-current_OS = platform.system()
-
-env = DefaultEnvironment()
-
-build_type = os.environ.get("BUILD_TYPE", 'Not Set')
-
-
-if not(build_type == 'upload' or build_type == 'traceback' or build_type == 'Not Set') :
-  env.Replace(UPLOAD_PROTOCOL = 'teensy-gui')  # run normal Teensy2 scripts
-else:
-  com_first = ''
-  com_last = ''
-  com_CDC = ''
-  description_first = ''
-  description_last = ''
-  description_CDC = ''
-
-  #
-  # grab the first com port that pops up unless we find one we know for sure
-  # is a CDC device
-  #
-  def get_com_port(com_search_text, descr_search_text, start):
-
-      global com_first
-      global com_last
-      global com_CDC
-      global description_first
-      global description_last
-      global description_CDC
-
-
-      print('\nLooking for Serial Port\n')
-
-    # stream output from subprocess and split it into lines
-      pio_subprocess = subprocess.Popen(['platformio', 'device', 'list'], stdout=subprocess.PIPE, stderr=subprocess.STDOUT)
-
-      looking_for_description = False
-      for line in iter(pio_subprocess.stdout.readline, ''):
-          if 0 <= line.find(com_search_text):
-            looking_for_description = True
-            com_last = line.replace('\n', '')
-            if com_first == '':
-              com_first = com_last
-          if 0 <= line.find(descr_search_text) and looking_for_description:
-            looking_for_description = False
-            description_last = line[ start : ]
-            if description_first == '':
-              description_first = description_last
-            if 0 <= description_last.find('CDC'):
-              com_CDC = com_last
-              description_CDC = description_last
-
-      if  com_CDC == '' and com_first != '':
-          com_CDC = com_first
-          description_CDC = description_first
-      elif com_CDC == '':
-            com_CDC = 'COM_PORT_NOT_FOUND'
-
-      while 0 <= com_CDC.find('\n'):
-        com_CDC = com_CDC.replace('\n', '')
-      while 0 <= com_CDC.find('\r'):
-        com_CDC = com_CDC.replace('\r', '')
-
-      if com_CDC == 'COM_PORT_NOT_FOUND':
-          print(com_CDC, '\n')
-      else:
-          print('FOUND: ', com_CDC)
-          print('DESCRIPTION: ', description_CDC, '\n')
-
-  if current_OS == 'Windows':
-
-      get_com_port('COM', 'Hardware ID:', 13)
-
-  #    avrdude_conf_path =  env.get("PIOHOME_DIR") + '\\packages\\toolchain-atmelavr\\etc\\avrdude.conf'
-      avrdude_conf_path =  'buildroot\\share\\vscode\\avrdude.conf'
-
-      avrdude_exe_path =  'buildroot\\share\\vscode\\avrdude_5.10.exe'
-
-  #    source_path = env.get("PROJECTBUILD_DIR") + '\\' + env.get("PIOENV") + '\\firmware.hex'
-      source_path =  '.pio\\build\\' + env.get("PIOENV") + '\\firmware.hex'
-
-      upload_string = avrdude_exe_path + ' -p usb1286 -c avr109 -P ' + com_CDC + ' -U flash:w:' + source_path + ':i'
-
-
-  if current_OS == 'Darwin':  # MAC
-
-      get_com_port('usbmodem', 'Description:', 13)
-
-#      avrdude_conf_path =  env.get("PIOHOME_DIR") + '/packages/toolchain-atmelavr/etc/avrdude.conf'
-      avrdude_conf_path =  'buildroot/share/vscode/avrdude_macOS.conf'
-
-
-      avrdude_exe_path =  'buildroot/share/vscode/avrdude_5.10_macOS'
-
-#      source_path = env.get("PROJECTBUILD_DIR") + '/' + env.get("PIOENV") + '/firmware.hex'
-      source_path = '.pio/build/' + env.get("PIOENV") + '/firmware.hex'
-
-
-#      upload_string = 'avrdude -p usb1286 -c avr109 -P ' + com_CDC + ' -U flash:w:' + source_path + ':i'
-      upload_string = avrdude_exe_path + ' -p usb1286 -c avr109 -P ' + com_CDC + ' -C ' + avrdude_conf_path  + ' -U flash:w:' + source_path + ':i'
-      print('upload_string: ', upload_string)
-
-
-
-  if current_OS == 'Linux':
-
-      get_com_port('/dev/tty', 'Description:', 13)
-
-#      avrdude_conf_path =  env.get("PIOHOME_DIR") + '/packages/toolchain-atmelavr/etc/avrdude.conf'
-      avrdude_conf_path =  'buildroot/share/vscode/avrdude_linux.conf'
-
-
-      avrdude_exe_path =  'buildroot/share/vscode/avrdude_5.10_linux'
-#      source_path = env.get("PROJECTBUILD_DIR") + '/' + env.get("PIOENV") + '/firmware.hex'
-      source_path = '.pio/build/' + env.get("PIOENV") + '/firmware.hex'
-
-#      upload_string = 'avrdude -p usb1286 -c avr109 -P ' + com_CDC + ' -U flash:w:' + source_path + ':i'
-      upload_string = avrdude_exe_path + ' -p usb1286 -c avr109 -P ' + com_CDC + ' -C ' + avrdude_conf_path  + ' -U flash:w:' + source_path + ':i'
-
-
-  env.Replace(
-       UPLOADCMD = upload_string,
-       MAXIMUM_RAM_SIZE = 8192,
-       MAXIMUM_SIZE = 130048
-  )
--- a/buildroot/share/vscode/create_custom_upload_command_DFU.py
+++ b/buildroot/share/vscode/create_custom_upload_command_DFU.py
@@ -1,41 +0,0 @@
-#
-#  Builds custom upload command
-#    1) Run platformio as a subprocess to find a COM port
-#    2) Build the upload command
-#    3) Exit and let upload tool do the work
-#
-#  This script runs between completion of the library/dependencies installation and compilation.
-#
-#  Will continue on if a COM port isn't found so that the compilation can be done.
-#
-
-import os, platform
-from SCons.Script import DefaultEnvironment
-
-current_OS = platform.system()
-
-env = DefaultEnvironment()
-
-build_type = os.environ.get("BUILD_TYPE", 'Not Set')
-if not(build_type == 'upload' or build_type == 'traceback' or build_type == 'Not Set') :
-  env.Replace(UPLOAD_PROTOCOL = 'teensy-gui')  # run normal Teensy2 scripts
-else:
-
-  if current_OS == 'Windows':
-      avrdude_conf_path =  env.get("PIOHOME_DIR") + '\\packages\\toolchain-atmelavr\\etc\\avrdude.conf'
-
-      source_path = env.get("PROJECTBUILD_DIR") + '\\' + env.get("PIOENV") + '\\firmware.hex'
-
-      upload_string = 'avrdude -p usb1286 -c flip1 -C ' + avrdude_conf_path + ' -U flash:w:' + source_path + ':i'
-
-  else:
-      source_path = env.get("PROJECTBUILD_DIR") + '/' + env.get("PIOENV") + '/firmware.hex'
-
-      upload_string = 'avrdude -p usb1286 -c flip1 -U flash:w:' + source_path + ':i'
-
-
-  env.Replace(
-       UPLOADCMD = upload_string,
-       MAXIMUM_RAM_SIZE = 8192,
-       MAXIMUM_SIZE = 130048
-  )
--- a/buildroot/tests/BIGTREE_GTR_V1_0
+++ b/buildroot/tests/BIGTREE_GTR_V1_0
@@ -24,7 +24,7 @@ restore_configs
 opt_set MOTHERBOARD BOARD_BTT_GTR_V1_0 SERIAL_PORT -1 \
        EXTRUDERS 5 TEMP_SENSOR_1 1 TEMP_SENSOR_2 1 TEMP_SENSOR_3 1 TEMP_SENSOR_4 1 \
        Z_DRIVER_TYPE A4988 Z2_DRIVER_TYPE A4988 Z3_DRIVER_TYPE A4988 Z4_DRIVER_TYPE A4988 \
-        DEFAULT_Kp_LIST '{ 22.2, 20.0, 21.0, 19.0, 18.0 }' DEFAULT_Ki_LIST '{ 1.08 }' DEFAULT_Kd_LIST '{ 114.0, 112.0, 110.0, 108.0 }'
+        DEFAULT_KP_LIST '{ 22.2, 20.0, 21.0, 19.0, 18.0 }' DEFAULT_KI_LIST '{ 1.08 }' DEFAULT_KD_LIST '{ 114.0, 112.0, 110.0, 108.0 }'
 opt_enable TOOLCHANGE_FILAMENT_SWAP TOOLCHANGE_MIGRATION_FEATURE TOOLCHANGE_FS_SLOW_FIRST_PRIME TOOLCHANGE_FS_PRIME_FIRST_USED \
           REPRAP_DISCOUNT_SMART_CONTROLLER PID_PARAMS_PER_HOTEND Z_MULTI_ENDSTOPS
 exec_test $1 $2 "BigTreeTech GTR | 6 Extruders | Quad Z + Endstops" "$3"
--- a/buildroot/tests/mega2560ext
+++ b/buildroot/tests/mega2560ext
@@ -1,6 +1,6 @@
 #!/usr/bin/env bash
 #
-# Build tests for AVR ATmega FYSETC F6 1.3
+# Build tests for mega2560ext - AVR ATmega (extended)
 #

 # exit on first failure
@@ -64,7 +64,7 @@ opt_set MOTHERBOARD BOARD_FYSETC_F6_13 \
 opt_enable USE_ZMIN_PLUG FIX_MOUNTED_PROBE AUTO_BED_LEVELING_BILINEAR PAUSE_BEFORE_DEPLOY_STOW \
           FYSETC_242_OLED_12864 EEPROM_SETTINGS EEPROM_CHITCHAT M114_DETAIL Z_SAFE_HOMING \
           STEALTHCHOP_XY STEALTHCHOP_Z STEALTHCHOP_E HYBRID_THRESHOLD SENSORLESS_HOMING SQUARE_WAVE_STEPPING
-exec_test $1 $2 "FYSETC_F6 | SCARA | Mixed TMC | EEPROM" "$3"
+exec_test $1 $2 "SCARA | Mixed TMC | EEPROM" "$3"

 # clean up
 restore_configs
--- a/config/README.md
+++ b/config/README.md
@@ -1,3 +1,3 @@
 # Where have all the configurations gone?

-## https://github.com/MarlinFirmware/Configurations/archive/release-2.1.2.5.zip
+## https://github.com/MarlinFirmware/Configurations/archive/release-2.1.2.7.zip
--- a/ini/avr.ini
+++ b/ini/avr.ini
@@ -87,13 +87,6 @@ board    = megaatmega2560
 extends  = common_avr8
 board    = reprap_rambo

-#
-# FYSETC F6 V1.3 / V1.4
-#
-[env:FYSETC_F6]
-extends  = common_avr8
-board    = fysetc_f6_13
-
 #
 # Sanguinololu (ATmega644p)
 #
--- a/ini/native.ini
+++ b/ini/native.ini
@@ -30,10 +30,10 @@ extends          = env:linux_native
 extra_scripts    = ${common.extra_scripts}
                   post:buildroot/share/PlatformIO/scripts/collect-code-tests.py
 build_src_filter = ${env:linux_native.build_src_filter} +<tests>
-lib_deps         = throwtheswitch/Unity@^2.5.2
+lib_deps         = throwtheswitch/Unity@^2.6.0
 test_build_src   = true
 build_unflags    =
-build_flags      = ${env:linux_native.build_flags} -Werror
+build_flags      = ${env:linux_native.build_flags} -Werror -DNO_USER_FEEDBACK_WARNING

 #
 # Native Simulation
@@ -58,7 +58,7 @@ debug_build_flags = -fstack-protector-strong -g -g3 -ggdb
 lib_compat_mode   = off
 build_src_filter  = ${common.default_src_filter} +<src/HAL/NATIVE_SIM>
 lib_deps          = ${common.lib_deps}
-                    MarlinSimUI=https://github.com/p3p/MarlinSimUI/archive/afe7c1c293.zip
+                    MarlinSimUI=https://github.com/p3p/MarlinSimUI/archive/29c11d4f63.zip
                    Adafruit NeoPixel=https://github.com/p3p/Adafruit_NeoPixel/archive/c6b319f447.zip
                    LiquidCrystal=https://github.com/p3p/LiquidCrystal/archive/322fb5fc23.zip
 extra_scripts     = ${common.extra_scripts}
@@ -81,11 +81,15 @@ build_flags = ${simulator_linux.build_flags} ${simulator_linux.release_flags}
 # Simulator for macOS (MacPorts)
 #

+#
+# Use the script buildroot/bin/mac_gcc to prepare your environment.
 #
 # MacPorts:
+#  https://www.macports.org/install.php
+#
 #  sudo port install gcc14 glm mesa libsdl2 libsdl2_net
 #
-#  cd /opt/local/bin
+#  cd $(dirname "$(which port)")
 #  sudo rm gcc g++ cc ld
 #  sudo ln -s gcc-mp-14 gcc ; sudo ln -s g++-mp-14 g++ ; sudo ln -s g++ cc
 #  sudo ln -s ld-classic ld
@@ -99,7 +103,7 @@ build_flags = ${simulator_linux.build_flags} ${simulator_linux.release_flags}
 #
 #  brew install gcc@14 glm mesa sdl2 sdl2_net
 #
-#  cd /opt/homebrew/bin
+#  cd "$(brew --prefix)/bin"
 #  sudo rm -f gcc g++ cc
 #  sudo ln -s gcc-14 gcc ; sudo ln -s g++-14 g++ ; sudo ln -s g++ cc
 #  cd -
@@ -111,7 +115,7 @@ build_flags       = -g2
  -DHAS_LIBBSD
  -I/opt/local/include
  -I/opt/local/include/freetype2
-  -I/opt/local/include/SDL2/
+  -I/opt/local/include/SDL2
  -L/opt/local/lib
  -Wl,-framework,OpenGl
  -Wl,-framework,CoreFoundation
--- a/ini/renamed.ini
+++ b/ini/renamed.ini
@@ -95,3 +95,6 @@ extends = renamed

 [env:STM32F407ZE_btt_USB]             ;=> STM32F407ZE_btt_usb_flash_drive
 extends = renamed
+
+[env:FYSETC_F6]                       ;=> mega2560ext
+extends = renamed
--- a/ini/samd21.ini
+++ b/ini/samd21.ini
@@ -10,7 +10,7 @@
 #################################

 #
-# Adafruit Grand Central M4 (Atmel SAMD51P20A ARM Cortex-M4)
+# ReprapWorld Minitronics (Atmel SAMD21J18 ARM Cortex-M0+)
 #
 [env:SAMD21_minitronics20]
 platform         = atmelsam
--- a/ini/stm32f1-maple.ini
+++ b/ini/stm32f1-maple.ini
@@ -23,7 +23,7 @@
 # HAL/STM32F1 Common Environment values
 #
 [STM32F1_maple]
-platform          = ststm32@~12.1
+platform          = ststm32@~15.4.1
 board_build.core  = maple
 build_flags       = !python Marlin/src/HAL/STM32F1/build_flags.py
                    ${common.build_flags} -DARDUINO_ARCH_STM32 -DMAPLE_STM32F1 -DPLATFORM_M997_SUPPORT
@@ -31,13 +31,18 @@ build_unflags     = -std=gnu11 -std=gnu++11
 build_src_filter  = ${common.default_src_filter} +<src/HAL/STM32F1> -<src/HAL/STM32F1/tft>
 lib_ignore        = SPI, FreeRTOS701, FreeRTOS821
 lib_deps          = ${common.lib_deps}
-  SoftwareSerialM
+                    SoftwareSerialM
 platform_packages = tool-stm32duino
+                    toolchain-gccarmnoneeabi@1.120301.0   # Otherwise it's GCC 7.2.1
 extra_scripts     = ${common.extra_scripts}
                    pre:buildroot/share/PlatformIO/scripts/fix_framework_weakness.py
                    pre:buildroot/share/PlatformIO/scripts/stm32_serialbuffer.py
                        buildroot/share/PlatformIO/scripts/custom_board.py
                        buildroot/share/PlatformIO/scripts/offset_and_rename.py
+custom_marlin.HAS_SPI_TFT     = build_src_filter=+<src/HAL/STM32F1/tft/tft_spi.cpp>
+custom_marlin.HAS_TFT_XPT2046 = build_src_filter=+<src/HAL/STM32F1/tft/xpt2046.cpp>
+custom_marlin.HAS_FSMC_TFT    = build_src_filter=+<src/HAL/STM32F1/tft/tft_fsmc.cpp>
+custom_marlin.NEOPIXEL_LED    = Adafruit NeoPixel=https://github.com/ccccmagicboy/Adafruit_NeoPixel#meeb_3dp_use

 #
 # Generic STM32F103RC environment
@@ -61,6 +66,8 @@ monitor_speed = 115200
 [env:STM32F103RC_meeb_maple]
 extends              = env:STM32F103RC_maple
 board                = marlin_maple_MEEB_3DP
+platform_packages    = ${env:STM32F103RC_maple.platform_packages}
+                       platformio/tool-dfuutil@~1.11.0
 build_flags          = ${env:STM32F103RC_maple.build_flags}
                       -DDEBUG_LEVEL=0
                       -DSS_TIMER=4
@@ -69,13 +76,13 @@ build_flags          = ${env:STM32F103RC_maple.build_flags}
                       -DUSE_USB_COMPOSITE
                       -DVECT_TAB_OFFSET=0x2000
                       -DGENERIC_BOOTLOADER
+                       -DNO_MAPLE_WARNING
 board_build.ldscript = STM32F103RC_MEEB_3DP.ld
 extra_scripts        = ${env:STM32F103RC_maple.extra_scripts}
                       pre:buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py
                           buildroot/share/PlatformIO/scripts/STM32F103RC_MEEB_3DP.py
 lib_deps             = ${env:STM32F103RC_maple.lib_deps}
-                       USBComposite for STM32F1@0.91
-custom_marlin.NEOPIXEL_LED = Adafruit NeoPixel=https://github.com/ccccmagicboy/Adafruit_NeoPixel#meeb_3dp_use
+                       USBComposite for STM32F1@1.0.9
 debug_tool           = stlink
 upload_protocol      = dfu

@@ -83,13 +90,13 @@ upload_protocol      = dfu
 # FYSETC STM32F103RC
 #
 [env:STM32F103RC_fysetc_maple]
-extends         = env:STM32F103RC_maple
-extra_scripts   = ${env:STM32F103RC_maple.extra_scripts}
-                  buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py
-build_flags     = ${env:STM32F103RC_maple.build_flags} -DDEBUG_LEVEL=0
-lib_ldf_mode    = chain
-debug_tool      = stlink
-upload_protocol = serial
+extends           = env:STM32F103RC_maple
+extra_scripts     = ${env:STM32F103RC_maple.extra_scripts}
+                    buildroot/share/PlatformIO/scripts/STM32F103RC_fysetc.py
+build_flags       = ${env:STM32F103RC_maple.build_flags} -DDEBUG_LEVEL=0
+lib_ldf_mode      = chain
+debug_tool        = stlink
+upload_protocol   = serial

 #
 # BigTreeTech SKR Mini V1.1 / SKR Mini E3 & MZ (STM32F103RCT6 ARM Cortex-M3)
@@ -108,7 +115,7 @@ monitor_speed        = 115200
 extends     = env:STM32F103RC_btt_maple
 build_flags = ${env:STM32F103RC_btt_maple.build_flags} -DUSE_USB_COMPOSITE
 lib_deps    = ${env:STM32F103RC_btt_maple.lib_deps}
-              USBComposite for STM32F1@0.91
+              USBComposite for STM32F1@1.0.9

 #
 # Creality 512K (STM32F103RET6)
@@ -160,7 +167,7 @@ upload_protocol      = stlink
 extends     = env:STM32F103RE_btt_maple
 build_flags = ${env:STM32F103RE_btt_maple.build_flags} -DUSE_USB_COMPOSITE
 lib_deps    = ${env:STM32F103RE_btt_maple.lib_deps}
-              USBComposite for STM32F1@0.91
+              USBComposite for STM32F1@1.0.9

 #
 # Geeetech GTM32 (STM32F103VET6)
@@ -185,7 +192,7 @@ board_build.address  = 0x08010000
 board_build.rename   = project.bin
 board_build.ldscript = STM32F103VE_longer.ld
 build_flags          = ${STM32F1_maple.build_flags}
-                       -DMCU_STM32F103VE -DSTM32F1xx -USERIAL_USB -DU20 -DTS_V12
+                       -DMCU_STM32F103VE -DSTM32F1xx -DSERIAL_USB -DU20 -DTS_V12
 build_unflags        = ${STM32F1_maple.build_unflags}
                       -DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG=1 -DERROR_LED_PORT=GPIOE -DERROR_LED_PIN=6

@@ -236,6 +243,7 @@ board_build.ldscript    = mks_robin_pro.ld
 #
 [env:trigorilla_pro_maple]
 extends       = env:mks_robin_maple
+build_flags   = ${env:mks_robin_maple.build_flags} -DSTM32_FLASH_SIZE=512

 #
 # MKS Robin E3D (STM32F103RCT6) and
@@ -311,14 +319,15 @@ lib_ignore  = ${STM32F1_maple.lib_ignore}
 # Chitu boards like Tronxy X5s (STM32F103ZET6)
 #
 [env:chitu_f103_maple]
-extends       = STM32F1_maple
-board         = marlin_maple_CHITU_F103
-extra_scripts = ${STM32F1_maple.extra_scripts}
-                pre:buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py
-                    buildroot/share/PlatformIO/scripts/chitu_crypt.py
-build_flags   = ${STM32F1_maple.build_flags} -DSTM32F1xx -DSTM32_XL_DENSITY
-build_unflags = ${STM32F1_maple.build_unflags}
-                -DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG= -DERROR_LED_PORT=GPIOE -DERROR_LED_PIN=6
+extends                 = STM32F1_maple
+board                   = marlin_maple_CHITU_F103
+extra_scripts           = ${STM32F1_maple.extra_scripts}
+                          pre:buildroot/share/PlatformIO/scripts/STM32F1_create_variant.py
+                              buildroot/share/PlatformIO/scripts/chitu_crypt.py
+build_flags             = ${STM32F1_maple.build_flags} -DSTM32F1xx -DSTM32_XL_DENSITY -DSTM32_FLASH_SIZE=512
+build_unflags           = ${STM32F1_maple.build_unflags}
+                          -DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG= -DERROR_LED_PORT=GPIOE -DERROR_LED_PIN=6
+board_build.crypt_chitu = update.cbd

 #
 # Some Chitu V5 boards have a problem with GPIO init.
@@ -353,8 +362,8 @@ board_upload.maximum_size = 237568
 build_flags               = ${STM32F1_maple.build_flags}
                            -D__STM32F1__=1 -DDEBUG_LEVEL=0 -DSS_TIMER=4 -DSERIAL_USB
 lib_deps                  = ${STM32F1_maple.lib_deps}
-                            USBComposite for STM32F1@0.91
-lib_ignore                = Adafruit NeoPixel, SPI, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster, TMCStepper
+                            USBComposite for STM32F1@1.0.9
+lib_ignore                = Adafruit NeoPixel, SPI, SailfishLCD, SailfishRGB_LED, SlowSoftI2CMaster

 [env:STM32F103RC_ZM3E2_USB_maple]
 extends              = ZONESTAR_ZM3E_maple
@@ -385,6 +394,7 @@ build_flags          = ${STM32F1_maple.build_flags}
                       -DMCU_STM32F103VE -DARDUINO_GENERIC_STM32F103V -DARDUINO_ARCH_STM32F1
                       -DDEBUG_LEVEL=DEBUG_NONE -DCONFIG_MAPLE_MINI_NO_DISABLE_DEBUG=1
                       -DSS_TIMER=4
+                       -DNO_MAPLE_WARNING
 board_build.variant  = MARLIN_F103Vx
 board_build.ldscript = eryone_ery32_mini.ld
 board_build.address  = 0x08004000
@@ -395,7 +405,7 @@ build_unflags        = ${STM32F1_maple.build_unflags}
 #
 [env:GD32F103RET6_sovol_maple]
 extends              = env:STM32F103RE_maple
-build_flags          = ${STM32F1_maple.build_flags} -DTEMP_TIMER_CHAN=4
+build_flags          = ${STM32F1_maple.build_flags} -DTEMP_TIMER_CHAN=4 -DNO_MAPLE_WARNING
 board_build.address  = 0x08007000
 board_build.ldscript = sovol.ld
 board_build.rename   = firmware-{date}-{time}.bin
--- a/ini/stm32f1.ini
+++ b/ini/stm32f1.ini
@@ -63,15 +63,15 @@ build_flags                 = ${common_STM32F103RC_variant.build_flags}
 board_build.offset          = 0x7000
 board_upload.offset_address = 0x08007000

+[USBD_CDC_MSC]
+build_flags   = -DUSE_USB_FS -DUSBD_USE_CDC_MSC -DUSBD_IRQ_PRIO=5 -DUSBD_IRQ_SUBPRIO=6
+build_unflags = -DUSBD_USE_CDC
+
 [env:STM32F103RC_btt_USB]
 extends           = env:STM32F103RC_btt
 platform_packages = ${stm_flash_drive.platform_packages}
-build_flags       = ${env:STM32F103RC_btt.build_flags}
-                    -DUSE_USB_FS
-                    -DUSBD_IRQ_PRIO=5
-                    -DUSBD_IRQ_SUBPRIO=6
-                    -DUSBD_USE_CDC_MSC
-build_unflags     = ${common_stm32.build_unflags} -DUSBD_USE_CDC
+build_flags       = ${env:STM32F103RC_btt.build_flags} ${USBD_CDC_MSC.build_flags}
+build_unflags     = ${env:STM32F103RC_btt.build_unflags} ${USBD_CDC_MSC.build_unflags}

 #
 # Panda Pi V2.9 - Standalone (STM32F103RC)
@@ -83,8 +83,8 @@ build_flags                 = ${common_STM32F103RC_variant.build_flags}
                              -DTIMER_SERVO=TIM1
 board_build.offset          = 0x5000
 board_upload.offset_address = 0x08005000
-lib_deps =
-  markyue/Panda_SoftMasterI2C@1.0.3
+lib_deps                    = markyue/Panda_SoftMasterI2C@1.0.3
+
 #
 # MKS Robin (STM32F103ZET6)
 # Uses HAL STM32 to support Marlin UI for TFT screen with optional touch panel
@@ -95,6 +95,7 @@ board                   = genericSTM32F103ZE
 board_build.variant     = MARLIN_F103Zx
 board_build.encrypt_mks = Robin.bin
 board_build.offset      = 0x7000
+board_build.offset_address = 0x08007000
 build_flags             = ${stm32_variant.build_flags}
                          -DENABLE_HWSERIAL3 -DTIMER_SERIAL=TIM5
 build_unflags           = ${stm32_variant.build_unflags}
@@ -121,8 +122,8 @@ debug_tool                  = stlink
 extends                     = stm32_variant
 board_build.variant         = MARLIN_F103Rx
 board_build.offset          = 0x7000
-board_build.rename          = firmware-{date}-{time}.bin
 board_upload.offset_address = 0x08007000
+board_build.rename          = firmware-{date}-{time}.bin
 build_flags                 = ${stm32_variant.build_flags}
                              -DMCU_STM32F103RE -DHAL_SD_MODULE_ENABLED
                              -DSS_TIMER=4 -DTIMER_SERVO=TIM5
@@ -177,6 +178,7 @@ board_upload.offset_address = 0x08010000
 extends                     = env:STM32F103RE_creality
 board_build.offset          = 0x8000
 board_upload.offset_address = 0x08008000
+board_build.rename          = main_board_{date}_{time}.bin

 #
 # Creality 256K (STM32F103RC)
@@ -199,7 +201,7 @@ board   = genericSTM32F103RC
 extends             = STM32F103Rx_creality
 board               = genericSTM32F103VE
 board_build.variant = MARLIN_F103Vx
-build_flags         = ${stm32_variant.build_flags}
+build_flags         = ${STM32F103Rx_creality.build_flags}
                      -DSS_TIMER=4 -DTIMER_SERVO=TIM5
                      -DENABLE_HWSERIAL3 -DTRANSFER_CLOCK_DIV=8
 #
@@ -225,10 +227,8 @@ upload_protocol             = jlink
 [env:STM32F103RE_btt_USB]
 extends           = env:STM32F103RE_btt
 platform_packages = ${stm_flash_drive.platform_packages}
-build_flags       = ${env:STM32F103RE_btt.build_flags}
-                    -DUSE_USB_FS -DUSBD_IRQ_PRIO=5
-                    -DUSBD_IRQ_SUBPRIO=6 -DUSBD_USE_CDC_MSC
-build_unflags     = ${env:STM32F103RE_btt.build_unflags} -DUSBD_USE_CDC
+build_flags       = ${env:STM32F103RE_btt.build_flags} ${USBD_CDC_MSC.build_flags}
+build_unflags     = ${env:STM32F103RE_btt.build_unflags} ${USBD_CDC_MSC.build_unflags}

 #
 # Mingda MPX_ARM_MINI
@@ -238,6 +238,7 @@ extends              = stm32_variant
 board                = genericSTM32F103ZE
 board_build.variant  = MARLIN_F103Zx
 board_build.offset   = 0x10000
+board_build.offset_address = 0x08010000
 build_flags          = ${stm32_variant.build_flags}
                       -DENABLE_HWSERIAL3 -DTIMER_SERIAL=TIM5
 build_unflags        = ${stm32_variant.build_unflags}
@@ -252,7 +253,7 @@ board            = malyanm200_f103cb
 build_flags      = ${common_stm32.build_flags}
                   -DHAL_PCD_MODULE_ENABLED -DDISABLE_GENERIC_SERIALUSB
                   -DHAL_UART_MODULE_ENABLED
-build_src_filter = ${common.default_src_filter} +<src/HAL/STM32> -<src/HAL/STM32/tft>
+build_src_filter = ${common_stm32.build_src_filter} +<src/HAL/STM32> -<src/HAL/STM32/tft>

 #
 # FLYmaker FLY Mini (STM32F103RCT6)
@@ -263,7 +264,7 @@ board                       = genericSTM32F103RC
 board_build.variant         = MARLIN_F103Rx
 board_build.offset          = 0x5000
 board_upload.offset_address = 0x08005000
-build_flags                 = ${stm32_variant.build_flags} -DSS_TIMER=4
+build_flags                 = ${stm32_variant.build_flags} -DSS_TIMER=4 -DSTM32_FLASH_SIZE=256

 #
 # (STM32F103VE_robin)
@@ -361,6 +362,8 @@ board_build.offset          = 0xA000
 board_upload.offset_address = 0x0800A000
 build_flags                 = ${stm32_variant.build_flags}
                              -DSTM32F1xx -DSTM32_XL_DENSITY
+build_unflags               = ${stm32_variant.build_unflags}
+                              -DUSBCON -DUSBD_USE_CDC
 extra_scripts               = ${stm32_variant.extra_scripts}
                              buildroot/share/PlatformIO/scripts/jgaurora_a5s_a1_with_bootloader.py

@@ -402,7 +405,7 @@ extends              = stm32_variant
 board                = genericSTM32F103ZE
 board_build.variant  = MARLIN_F103Zx
 build_flags          = ${stm32_variant.build_flags}
-                       -DENABLE_HWSERIAL3 -DTIMER_SERIAL=TIM5
+                       -DENABLE_HWSERIAL3 -DTIMER_SERIAL=TIM5 -DSTM32_FLASH_SIZE=512
 build_unflags        = ${stm32_variant.build_unflags}
                       -DUSBCON -DUSBD_USE_CDC

@@ -416,6 +419,7 @@ board                = genericSTM32F103ZE
 board_build.crypt_chitu = update.zw
 board_build.variant  = MARLIN_F103Zx
 board_build.offset   = 0x8800
+board_build.offset_address = 0x08008800
 build_flags          = ${stm32_variant.build_flags}
                       -DENABLE_HWSERIAL3 -DTIMER_SERIAL=TIM5
 build_unflags        = ${stm32_variant.build_unflags}
@@ -433,8 +437,8 @@ board                = genericSTM32F103ZE
 board_build.crypt_chitu = update.cbd
 board_build.variant  = MARLIN_F103Zx
 board_build.offset   = 0x8800
-build_flags          = ${stm32_variant.build_flags}
-                       -DSTM32F1xx
+board_build.offset_address = 0x08008800
+build_flags          = ${stm32_variant.build_flags} -DSTM32F1xx -DSTM32_FLASH_SIZE=512
 build_unflags        = ${stm32_variant.build_unflags}
 extra_scripts        = ${stm32_variant.extra_scripts}
                       buildroot/share/PlatformIO/scripts/chitu_crypt.py
@@ -457,13 +461,13 @@ build_flags   = ${env:chitu_f103.build_flags} -DCHITU_V5_Z_MIN_BUGFIX
 [ZONESTAR_ZM3E]
 extends                   = stm32_variant
 platform_packages         = ${stm_flash_drive.platform_packages}
-board_upload.offset_address = 0x08005000
 board_build.offset        = 0x5000
+board_upload.offset_address = 0x08005000
 board_upload.maximum_size = 237568
 extra_scripts             = ${stm32_variant.extra_scripts}
-build_flags               = ${common_stm32.build_flags}
-  -DSS_TIMER=4 -DTIMER_SERVO=TIM5 -DUSE_USB_FS -DUSBD_IRQ_PRIO=5 -DUSBD_IRQ_SUBPRIO=6 -DUSBD_USE_CDC_MSC
-build_unflags             = ${stm32_variant.build_unflags} -DUSBD_USE_CDC
+build_flags               = ${stm32_variant.build_flags} ${USBD_CDC_MSC.build_flags}
+                            -DSS_TIMER=4 -DTIMER_SERVO=TIM5
+build_unflags             = ${stm32_variant.build_unflags} ${USBD_CDC_MSC.build_unflags}

 [env:STM32F103RC_ZM3E2_USB]
 extends              = ZONESTAR_ZM3E
Author	SHA1	Message	Date
Scott Lahteine	3b8ab730b2	🔖 Version 2.1.2.7	2026-02-03 23:49:37 -06:00
ellensp	3f4c9834bb	🔨 Preflight check for future config (#28320 ) Co-authored-by: Scott Lahteine <thinkyhead@users.noreply.github.com>	2026-02-03 23:49:37 -06:00
Scott Lahteine	e2208ba58f	🔨 Build quality improvements	2026-01-22 21:40:56 -06:00
Andrivet	57906a8466	🐛 Fix TFT LVGL UI + Y-DIR conflict (#28291 ) Fixes #22967	2026-01-22 10:44:31 -06:00
Scott Lahteine	c67f981197	🩹 Fix offset_xy build error	2026-01-22 10:44:31 -06:00
Scott Lahteine	cd4dcee8c1	🔨 Remove dead envs	2026-01-22 10:44:31 -06:00
Scott Lahteine	652a619549	🔨 Update build scripts	2026-01-22 10:44:31 -06:00
Scott Lahteine	5554ccb52f	🔖 Version 2.1.2.6	2026-01-15 16:27:56 -06:00
Scott Lahteine	f869f0eb3b	🔨 No such env env:DUE_debug	2026-01-15 16:27:56 -06:00
Scott Lahteine	14708a3067	Update build scripts	2026-01-14 18:28:59 -06:00
Scott Lahteine	324ce04698	🔧 Uppercase PID, etc.	2026-01-14 18:28:58 -06:00
Scott Lahteine	75a98c6181	🐛 Fix Teensy 4.x stepper timing (#28169 ) 🧑‍💻 Timer general cleanup 🩹 Teensy 4.x timer mods	2025-11-20 15:25:16 -06:00
ellensp	0f2a057c24	🔨🐛 Don't use broken 'board = fysetc_f6_13' (#28159 )	2025-11-05 17:23:55 -06:00
ellensp	d6c4e2f98f	🐛 Fix Hotend > 0 Preheat (#27932 )	2025-06-20 16:19:21 -05:00
Scott Lahteine	429b5bcd72	🩹 Fix Y_STOP_PIN alias for Y_MAX_PIN	2025-05-04 15:22:44 -05:00
ellensp	21edd52063	🐛 Fix RAMPS AUX1 RX/TX pins (#27745 )	2025-03-19 15:46:52 -05:00
ellensp	a4b7341bbe	🩹 Fix missing BTT_SKR_MINI_E3_V3_0_1 include (#27696 )	2025-03-19 15:46:52 -05:00
Scott Lahteine	48142ac7c6	📝 Update HAL documentation, README	2025-03-19 15:46:52 -05:00
Scott Lahteine	f0b960e2ef	🧑‍💻 Update example build scripts	2024-12-16 15:25:47 -06:00
Scott Lahteine	c7e10c5622	🩹 Fix build with Color UI touch items	2024-12-16 15:06:38 -06:00