mirror of
https://github.com/greatscottgadgets/hackrf.git
synced 2026-02-20 00:33:48 +01:00
409acbc3c9
Co-authored-by: mndza <diego.hdmp@gmail.com> Co-authored-by: Martin Ling <martin-git@earth.li> Co-authored-by: Antoine van Gelder <antoine@greatscottgadgets.com>
102 lines
3.4 KiB
C
102 lines
3.4 KiB
C
/*
|
|
* Copyright 2025 Great Scott Gadgets <info@greatscottgadgets.com>
|
|
*
|
|
* This file is part of HackRF.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation; either version 2, or (at your option)
|
|
* any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; see the file COPYING. If not, write to
|
|
* the Free Software Foundation, Inc., 51 Franklin Street,
|
|
* Boston, MA 02110-1301, USA.
|
|
*/
|
|
|
|
#include "max2831_target.h"
|
|
|
|
#include <libopencm3/lpc43xx/scu.h>
|
|
#include "hackrf_core.h"
|
|
|
|
void max2831_target_init(max2831_driver_t* const drv)
|
|
{
|
|
/* Configure SSP1 Peripheral (to be moved later in SSP driver) */
|
|
scu_pinmux(SCU_SSP1_COPI, (SCU_SSP_IO | SCU_CONF_FUNCTION5));
|
|
scu_pinmux(SCU_SSP1_SCK, (SCU_SSP_IO | SCU_CONF_FUNCTION1));
|
|
|
|
scu_pinmux(SCU_XCVR_CS, SCU_XCVR_CS_PINCFG);
|
|
|
|
/*
|
|
* Configure XCVR_CTL GPIO pins.
|
|
*
|
|
* The RXTX pin is also known as RXENABLE because of its use on the
|
|
* MAX2837 which had a separate TXENABLE. On MAX2831 a single RXTX pin
|
|
* switches between RX (high) and TX (low) modes.
|
|
*/
|
|
scu_pinmux(SCU_XCVR_ENABLE, SCU_XCVR_ENABLE_PINCFG);
|
|
scu_pinmux(SCU_XCVR_RXENABLE, SCU_XCVR_RXENABLE_PINCFG);
|
|
scu_pinmux(SCU_XCVR_RXHP, SCU_XCVR_RXHP_PINCFG);
|
|
scu_pinmux(SCU_XCVR_LD, SCU_XCVR_LD_PINCFG);
|
|
|
|
/* Set GPIO pins as outputs. */
|
|
gpio_output(drv->gpio_enable);
|
|
gpio_output(drv->gpio_rxtx);
|
|
gpio_output(drv->gpio_rxhp);
|
|
gpio_input(drv->gpio_ld);
|
|
}
|
|
|
|
void max2831_target_set_mode(max2831_driver_t* const drv, const max2831_mode_t new_mode)
|
|
{
|
|
/* MAX2831_MODE_SHUTDOWN:
|
|
* All circuit blocks are powered down, except the 4-wire serial bus
|
|
* and its internal programmable registers.
|
|
*
|
|
* MAX2831_MODE_STANDBY:
|
|
* Used to enable the frequency synthesizer block while the rest of the
|
|
* device is powered down. In this mode, PLL, VCO, and LO generator
|
|
* are on, so that Tx or Rx modes can be quickly enabled from this mode.
|
|
* These and other blocks can be selectively enabled in this mode.
|
|
*
|
|
* MAX2831_MODE_TX:
|
|
* All Tx circuit blocks are powered on. The external PA is powered on
|
|
* after a programmable delay using the on-chip PA bias DAC. The slow-
|
|
* charging Rx circuits are in a precharged “idle-off” state for fast
|
|
* Tx-to-Rx turnaround time.
|
|
*
|
|
* MAX2831_MODE_RX:
|
|
* All Rx circuit blocks are powered on and active. Antenna signal is
|
|
* applied; RF is downconverted, filtered, and buffered at Rx BB I and Q
|
|
* outputs. The slow- charging Tx circuits are in a precharged “idle-off”
|
|
* state for fast Rx-to-Tx turnaround time.
|
|
*/
|
|
|
|
switch (new_mode) {
|
|
default:
|
|
case MAX2831_MODE_SHUTDOWN:
|
|
gpio_clear(drv->gpio_rxtx);
|
|
gpio_clear(drv->gpio_enable);
|
|
break;
|
|
case MAX2831_MODE_STANDBY:
|
|
gpio_set(drv->gpio_rxtx);
|
|
gpio_clear(drv->gpio_enable);
|
|
break;
|
|
case MAX2831_MODE_TX:
|
|
case MAX2831_MODE_TX_CALIBRATION:
|
|
gpio_set(drv->gpio_rxtx);
|
|
gpio_set(drv->gpio_enable);
|
|
break;
|
|
case MAX2831_MODE_RX:
|
|
case MAX2831_MODE_RX_CALIBRATION:
|
|
gpio_clear(drv->gpio_rxtx);
|
|
gpio_set(drv->gpio_enable);
|
|
break;
|
|
}
|
|
drv->mode = new_mode;
|
|
}
|