mirror of
https://github.com/1technophile/OpenMQTTGateway.git
synced 2026-03-14 11:18:14 +01:00
585df9a420
* Update arduino core to 3.1.1 * Fix Blufi build * Update arduinojson, fix build errors with idf * Fix narrowing * fix RF builds * WIP-Convert ino files to cpp * Fix pilight build * Fix Somfy actuator build. * Update esp32dev-rf partition * Fix Weatherstation build * Fix GFSunInverter build * Fix esp32dev-ir build * Fix ble-aws build * Fix eth builds * Fix m5Stack missing pins_arduino.h * Fix build errors for M5 stack/tough, others are upstream issues. * Fix RTL 433 build - remaining errors are from radolib * Fix nodemcu build * fix 2g builds * Fix serial build * Fix actuator on off builds * Fix SSD1306 build - remaining errors are from radiolib * Fix multiple definition of OTAserver_cert * Fix nodemcu rf2 build * Fix ADC builds * Fix sensor builds * Fix LORA builds * Fix multi-receiver builds - remaining errors are in radiolib * Fix fastled builds * Fix theegns board builds * Fix broker builds * Update fastled - old version failed all-test build * Fix RN8209 builds * Fix max temp actuator builds * Fix PWM builds * Fix C37 sensor builds * Fix HTU21 builds * Fix INA266 builds * Fix undefined variables in mqtt discovery * Fix webui build * Fix fastled invalid pin error * Fix wifi manual setup builds * Fix onewire/all-test build - bin too big error remaining * Fix theengs plug build * Fix rfbridge builds * Fix blufi builds * Fix undefined functions in serial * Fix preprocessor definition checks * Set IDF log level to erre * Add delay in loop to prevent watchdog timeout * Use xTaskCreateUniveral to support single core processors * Remove old HTTPUpdate files - upsteam fixed. * Cleanup and move common declarations to header file * Use custom partiton table to fix builds where bin is too large * Update M5StickC - fixs esp32-m5stick-c-ble build * Revert to Arduino core 2.x for builds with incompatible libs * Remove "Z" from file names and rename omg_common to TheengsCommon * Fix gateway name when using MAC with new Arduino core * Update IDF config to reduce loop task stack use * Update esp-nimble-cpp version, corrects BLE uppercase ID's * Update wifi manager to fix watchdog timeout error
249 lines
8.5 KiB
C++
249 lines
8.5 KiB
C++
/*
|
|
Theengs OpenMQTTGateway - We Unite Sensors in One Open-Source Interface
|
|
|
|
Act as a gateway between your 433mhz, infrared IR, BLE, LoRa signal and one interface like an MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the bluetooth low energy gateway (beacons detection)
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#ifndef config_BT_h
|
|
#define config_BT_h
|
|
|
|
#include "TheengsCommon.h"
|
|
|
|
extern void setupBT();
|
|
extern void XtoBT(const char* topicOri, JsonObject& RFdata);
|
|
extern void launchBTDiscovery(bool overrideDiscovery);
|
|
extern void stopProcessing(bool deinit);
|
|
extern String stateBTMeasures(bool);
|
|
|
|
#ifdef ESP32
|
|
# include "NimBLEDevice.h"
|
|
#endif
|
|
|
|
/*-----------BT TOPICS & COMPILATION PARAMETERS-----------*/
|
|
#define subjectBTtoMQTT "/BTtoMQTT"
|
|
#define subjectMQTTtoBTset "/commands/MQTTtoBT/config"
|
|
#define subjectMQTTtoBT "/commands/MQTTtoBT"
|
|
#define subjectTrackerSync "internal/trackersync"
|
|
// Uncomment to send undecoded device data to another gateway device for decoding
|
|
// #define MQTTDecodeTopic "undecoded"
|
|
#ifndef UseExtDecoder
|
|
# ifdef MQTTDecodeTopic
|
|
# define UseExtDecoder true
|
|
# else
|
|
# define UseExtDecoder false
|
|
# endif
|
|
#endif
|
|
#ifndef MQTTDecodeTopic
|
|
# define MQTTDecodeTopic "undecoded"
|
|
#endif
|
|
|
|
#ifndef AttemptBLEConnect
|
|
# define AttemptBLEConnect true //do we by default attempt a BLE connection to sensors with ESP32
|
|
#endif
|
|
|
|
#ifndef BLE_FILTER_CONNECTABLE
|
|
# define BLE_FILTER_CONNECTABLE 0 // Sets whether to filter publishing of scanned devices that require a connection.
|
|
#endif // Setting this to 1 prevents overwriting the publication of the device connection data with the advertised data (Recommended for use with OpenHAB).
|
|
|
|
#ifndef MinimumRSSI
|
|
# define MinimumRSSI -100 //default minimum rssi value, all the devices below -100 will not be reported
|
|
#endif
|
|
|
|
#ifndef Scan_duration
|
|
# define Scan_duration 10000 //define the duration for a scan; in milliseconds
|
|
#endif
|
|
#ifndef MinScanDuration
|
|
# define MinScanDuration 1000 //minimum duration for a scan; in milliseconds
|
|
#endif
|
|
#ifndef BLEScanInterval
|
|
# define BLEScanInterval 52 // How often the scan occurs / switches channels; in milliseconds,
|
|
#endif
|
|
#ifndef BLEScanWindow
|
|
# define BLEScanWindow 30 // How long to scan during the interval; in milliseconds.
|
|
#endif
|
|
#ifndef AdaptiveBLEScan
|
|
# define AdaptiveBLEScan true // Sets adaptive scanning, this will automatically decide on the best passive and active scanning intervals
|
|
#endif
|
|
#ifndef TimeBtwActive
|
|
# define TimeBtwActive 55555 //define default time between two BLE active scans when general passive scanning is selected; in milliseconds
|
|
#endif
|
|
#ifndef MinTimeBtwScan
|
|
# define MinTimeBtwScan 100 //define the time between two scans; in milliseconds
|
|
#endif
|
|
#ifndef TimeBtwConnect
|
|
# define TimeBtwConnect 3600000 //define default time between BLE connection attempt (not used for immediate actions); in milliseconds
|
|
#endif
|
|
#ifndef PresenceAwayTimer
|
|
# define PresenceAwayTimer 120000 //define the time between Offline Status update for the tracker sensors
|
|
#endif
|
|
#ifndef MovingTimer
|
|
# define MovingTimer 60000 //define the time between Offline Status update for the moving sensors with an accelerometer
|
|
#endif
|
|
|
|
#ifndef BLEScanDuplicateCacheSize
|
|
# define BLEScanDuplicateCacheSize 200
|
|
#endif
|
|
#ifndef TimeBtwRead
|
|
# define TimeBtwRead 55555 //define default time between 2 scans; in milliseconds
|
|
#endif
|
|
|
|
#ifndef PublishOnlySensors
|
|
# define PublishOnlySensors false //false if we publish all BLE devices discovered or true only the identified sensors (like temperature sensors)
|
|
#endif
|
|
|
|
#ifndef PublishRandomMACs
|
|
# define PublishRandomMACs false //false to not publish devices which randomly change their MAC addresses
|
|
#endif
|
|
|
|
#ifndef HassPresence
|
|
# define HassPresence false //true if we publish into Home Assistant presence topic
|
|
#endif
|
|
|
|
#ifndef EnableBT
|
|
# define EnableBT true
|
|
#endif
|
|
|
|
#ifndef BLEDecoder
|
|
# define BLEDecoder true //true if we use the Theengs decoder
|
|
#endif
|
|
|
|
#if !BLEDecoder
|
|
# define UNKWNON_MODEL -1
|
|
#else
|
|
# define UNKWNON_MODEL TheengsDecoder::BLE_ID_NUM::UNKNOWN_MODEL
|
|
#endif
|
|
|
|
#ifndef BLE_CNCT_TIMEOUT
|
|
# define BLE_CNCT_TIMEOUT 3000
|
|
#endif
|
|
|
|
extern unsigned long scanCount;
|
|
|
|
#ifndef pubBLEAdvData
|
|
# define pubBLEAdvData false // define true if you want to publish all advertisement data
|
|
#endif
|
|
|
|
#ifndef useBeaconUuidForTopic
|
|
# define useBeaconUuidForTopic false // define true to use iBeacon UUID as topic, instead of sender (random) MAC address
|
|
#endif
|
|
|
|
#ifndef enableMultiGTWSync
|
|
# define enableMultiGTWSync true // //define true to use tracker and closest control devices sync across OpenMQTTGateway and Theengs Gateway gateways
|
|
#endif
|
|
|
|
/*--------------HOME ASSISTANT ROOM PRESENCE--------------*/
|
|
#define subjectHomePresence "presence/" // will send Home Assistant room presence message to this topic (first part is same for all rooms, second is room name)
|
|
|
|
#ifndef useBeaconUuidForPresence
|
|
# define useBeaconUuidForPresence false // //define true to use iBeacon UUID as for presence, instead of sender MAC (random) address
|
|
#endif
|
|
|
|
/*----------------CONFIGURABLE PARAMETERS-----------------*/
|
|
struct BTConfig_s {
|
|
bool bleConnect; // Attempt a BLE connection to sensors with ESP32
|
|
bool adaptiveScan;
|
|
unsigned long intervalActiveScan; // Time between 2 active scans when generally passive scanning
|
|
unsigned long BLEinterval; // Time between 2 scans
|
|
unsigned long intervalConnect; // Time between 2 connects
|
|
unsigned long scanDuration; // Duration for a scan; in milliseconds
|
|
bool pubOnlySensors; // Publish only the identified sensors (like temperature sensors)
|
|
bool pubRandomMACs; // Publish devices which randomly change their MAC address
|
|
bool presenceEnable; // Publish into Home Assistant presence topic
|
|
String presenceTopic; // Home Assistant presence topic to publish on
|
|
bool presenceUseBeaconUuid; // Use iBeacon UUID as for presence, instead of sender MAC (random) address
|
|
int minRssi; // Minimum rssi value, all the devices below will not be reported
|
|
bool extDecoderEnable; // Send undecoded device data to another gateway device for decoding
|
|
String extDecoderTopic; // Topic to send undecoded device data on
|
|
bool filterConnectable; // Sets whether to filter publishing of scanned devices that require a connection.
|
|
bool pubAdvData; // Publish advertisement data
|
|
bool pubBeaconUuidForTopic; // Use iBeacon UUID as topic, instead of sender (random) MAC address
|
|
bool ignoreWBlist; // Disable Whitelist & Blacklist
|
|
unsigned long presenceAwayTimer; //Timer that trigger a tracker/PIR state as offline/off if not seen
|
|
unsigned long movingTimer; //Timer that trigger a moving sensor state as offline if not seen
|
|
bool forcePassiveScan; //Force passive scan
|
|
bool enabled; // Enable or disable the BT gateway
|
|
};
|
|
|
|
// Global struct to store live BT configuration data
|
|
extern BTConfig_s BTConfig;
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
#if !defined(BT_RX) || !defined(BT_TX)
|
|
# ifdef ESP8266
|
|
# define BT_RX 13 //D7 ESP8266 RX connect HM-10 or 11 TX
|
|
# define BT_TX 12 //D6 ESP8266 TX connect HM-10 or 11 RX
|
|
# elif defined(ESP32)
|
|
# define BT_RX 18 // not tested
|
|
# define BT_TX 19 // not tested
|
|
# else
|
|
# define BT_RX 5 //arduino RX connect HM-10 or 11 TX
|
|
# define BT_TX 6 //arduino TX connect HM-10 or 11 RX
|
|
# endif
|
|
#endif
|
|
|
|
/*---------------INTERNAL USE: DO NOT MODIFY--------------*/
|
|
#ifdef ESP32
|
|
enum ble_val_type {
|
|
BLE_VAL_STRING = 0,
|
|
BLE_VAL_HEX,
|
|
BLE_VAL_INT,
|
|
BLE_VAL_FLOAT,
|
|
};
|
|
|
|
struct BLEAction {
|
|
NimBLEAttValue value;
|
|
NimBLEAddress addr;
|
|
NimBLEUUID service;
|
|
NimBLEUUID characteristic;
|
|
bool write;
|
|
bool complete;
|
|
uint8_t ttl;
|
|
ble_val_type value_type;
|
|
};
|
|
#endif
|
|
|
|
struct BLEdevice {
|
|
char macAdr[18];
|
|
char name[20];
|
|
int macType;
|
|
bool isDisc;
|
|
bool isWhtL;
|
|
bool isBlkL;
|
|
bool connect;
|
|
int sensorModel_id;
|
|
unsigned long lastUpdate;
|
|
};
|
|
|
|
class BLEconectable {
|
|
public:
|
|
enum id {
|
|
MIN = 1000,
|
|
LYWSD03MMC,
|
|
MHO_C401,
|
|
DT24_BLE,
|
|
XMWSDJ04MMC,
|
|
MAX,
|
|
};
|
|
};
|
|
|
|
#endif
|