mirror of
https://github.com/mysensors/MySensors.git
synced 2026-02-20 01:21:27 +01:00
142 lines
4.8 KiB
C++
142 lines
4.8 KiB
C++
/*
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2026 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* REVISION HISTORY
|
|
* Version 1.0 - Henrik Ekblad
|
|
* Contribution by a-lurker and Anticimex
|
|
* Contribution by Norbert Truchsess <norbert.truchsess@t-online.de>
|
|
* Contribution by Tomas Hozza <thozza@gmail.com>
|
|
*
|
|
*
|
|
* DESCRIPTION
|
|
* The EthernetGateway sends data received from sensors to the ethernet link.
|
|
* The gateway also accepts input on ethernet interface, which is then sent out to the radio network.
|
|
*
|
|
* The GW code is designed for Arduino 328p / 16MHz. ATmega168 does not have enough memory to run this program.
|
|
*
|
|
* LED purposes:
|
|
* - To use the feature, uncomment MY_DEFAULT_xxx_LED_PIN in the sketch below
|
|
* - RX (green) - blink fast on radio message received. In inclusion mode will blink fast only on presentation received
|
|
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
|
|
* - ERR (red) - fast blink on error during transmission error or receive crc error
|
|
*
|
|
* See http://www.mysensors.org/build/ethernet_gateway for wiring instructions.
|
|
*
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
// Enable and select radio type attached
|
|
#define MY_RADIO_RF24
|
|
//#define MY_RADIO_NRF5_ESB
|
|
//#define MY_RADIO_RFM69
|
|
//#define MY_RADIO_RFM95
|
|
//#define MY_PJON
|
|
|
|
// Enable gateway ethernet module type
|
|
#define MY_GATEWAY_W5100
|
|
|
|
// W5100 Ethernet module SPI enable (optional if using a shield/module that manages SPI_EN signal)
|
|
//#define MY_W5100_SPI_EN 4
|
|
|
|
// Enable Soft SPI for NRF radio (note different radio wiring is required)
|
|
// The W5100 ethernet module seems to have a hard time co-operate with
|
|
// radio on the same spi bus.
|
|
#if !defined(MY_W5100_SPI_EN) && !defined(ARDUINO_ARCH_SAMD)
|
|
#define MY_SOFTSPI
|
|
#define MY_SOFT_SPI_SCK_PIN 14
|
|
#define MY_SOFT_SPI_MISO_PIN 16
|
|
#define MY_SOFT_SPI_MOSI_PIN 15
|
|
#endif
|
|
|
|
// When W5100 is connected we have to move CE/CSN pins for NRF radio
|
|
#ifndef MY_RF24_CE_PIN
|
|
#define MY_RF24_CE_PIN 5
|
|
#endif
|
|
#ifndef MY_RF24_CS_PIN
|
|
#define MY_RF24_CS_PIN 6
|
|
#endif
|
|
|
|
// Enable UDP communication
|
|
//#define MY_USE_UDP // If using UDP you need to set MY_CONTROLLER_IP_ADDRESS or MY_CONTROLLER_URL_ADDRESS below
|
|
|
|
// Enable MY_IP_ADDRESS here if you want a static ip address (no DHCP)
|
|
#define MY_IP_ADDRESS 192,168,178,66
|
|
|
|
// If using static ip you can define Gateway and Subnet address as well
|
|
//#define MY_IP_GATEWAY_ADDRESS 192,168,178,1
|
|
//#define MY_IP_SUBNET_ADDRESS 255,255,255,0
|
|
|
|
// The port to keep open on node server mode / or port to contact in client mode
|
|
#define MY_PORT 5003
|
|
|
|
// Controller ip address. Enables client mode (default is "server" mode).
|
|
// Also enable this if MY_USE_UDP is used and you want sensor data sent somewhere.
|
|
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 254
|
|
//#define MY_CONTROLLER_URL_ADDRESS "my.controller.org"
|
|
|
|
// The MAC address can be anything you want but MUST be unique on your network.
|
|
// Newer boards have a MAC address printed on the underside of the PCB, which you can (optionally) use.
|
|
// Note that most of the Arduino examples use "DEAD BEEF FEED" for the MAC address
|
|
// so make sure you don't have multiple Arduinos using the same MAC address.
|
|
#define MY_MAC_ADDRESS 0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED
|
|
|
|
|
|
// Enable inclusion mode
|
|
#define MY_INCLUSION_MODE_FEATURE
|
|
// Enable Inclusion mode button on gateway
|
|
//#define MY_INCLUSION_BUTTON_FEATURE
|
|
// Set inclusion mode duration (in seconds)
|
|
#define MY_INCLUSION_MODE_DURATION 60
|
|
// Digital pin used for inclusion mode button
|
|
//#define MY_INCLUSION_MODE_BUTTON_PIN 3
|
|
|
|
// Set blinking period
|
|
#define MY_DEFAULT_LED_BLINK_PERIOD 300
|
|
|
|
// Flash leds on rx/tx/err
|
|
// Uncomment to override default HW configurations
|
|
//#define MY_DEFAULT_ERR_LED_PIN 7 // Error led pin
|
|
//#define MY_DEFAULT_RX_LED_PIN 8 // Receive led pin
|
|
//#define MY_DEFAULT_TX_LED_PIN 9 // Transmit led pin
|
|
|
|
#if defined(MY_USE_UDP)
|
|
#include <EthernetUdp.h>
|
|
#endif
|
|
#include <Ethernet.h>
|
|
#include <MySensors.h>
|
|
|
|
void setup()
|
|
{
|
|
// Setup locally attached sensors
|
|
}
|
|
|
|
void presentation()
|
|
{
|
|
// Present locally attached sensors here
|
|
}
|
|
|
|
void loop()
|
|
{
|
|
// Send locally attached sensors data here
|
|
}
|
|
|